Question about Dishwashers

Open Question

Asea Cylinda 1400 dishwasher leaking underneath. Found wash pump seal leaking. Have removed pump and motor but can't remove impeller to get to seal.

Posted by on

  • Anonymous May 14, 2009

    asea cylinda 700 leaks from the bottom part,everthing else is fine

×

1 Suggested Answer

jyackle5
  • 8197 Answers

SOURCE: manual for Asko ASEA 1400 dishwasher

You can get the manual on the link below. It is uper right corner next to the man under the pdf. You will have to click on the stars to download.

http://safemanuals.com/user-guide-instructions-owner-manual/ASKO/1400-_E

Good Luck and please rate 4 thumbs up for the freee answer

Posted on Apr 24, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Manual for Asko ASEA 1400 dishwasher


You can get the manual on the link below. It is uper right corner next to the man under the pdf. You will have to click on the stars to download.

http://safemanuals.com/user-guide-instructions-owner-manual/ASKO/1400-_E

Good Luck and please rate 4 thumbs up for the freee answer

Apr 24, 2010 | Dishwashers

1 Answer

Both drawers leak in the front


If your dishwasher leaks, check these:
Main tub seal Note… If the main motor of your dishwasher is mounted vertically, beneath the center bottom of the dishwasher, the following instructions probably apply to you. But if your motor is mounted horizontally, the pump isn't serviceable--you need to replace the entire pump and motor assembly. The main tub seal is beneath the drain impeller. It prevents the water in the dishwasher from leaking out near the shaft of the motor. To get to the seal, which is inside the dishwasher, remove the:
  • Lower rack
  • Spray arm
  • Spray arm support
  • Wash/drain impellers
Then pry the seal out of its housing and replace it.

Door gasket or seal Over time, door gaskets and seals harden and lose their ability to seal properly. You can't repair the seals. You need to replace them if they've begun to leak.

Water-inlet valve The water-inlet valve, itself, seldom leaks. But, the water-supply line from the house and the rubber tube leading from the valve to the inside of the dishwasher may leak. Tighten or repair/replace these as necessary. The water-inlet valve could mechanically stick open. When that happens, the water continues to flow into the dishwasher, which then floods your kitchen. Turn off the water supply to the dishwasher, and replace the valve.

Hoses Behind the lower access panel on your dishwasher are several rubber or plastic hoses. If the leak appears at a connection, try a new clamp. If that doesn't work, replace the hose.

Apr 01, 2010 | Dishwashers

1 Answer

Removing a built in Asea Skandia cylinda 1200


Its normal to have the water supply from under sink to dishwasher 3/8 soft copper. If there is a water stop under sink for dishwasher go ahead and shut it off. If not you will have to shut water off at main. Now you can unscrew supply at dishwasher, it's close to the front on left side. Its a 3/8 compression nut, you can use a small cresent wrench.

Sep 30, 2009 | Dishwashers

2 Answers

The dishwasher will not drain all the way it is a DU810SWLQO


HI. check the following areas for faults.

1. Air gap / Drain hoses
If there is an air gap (located in the sink, near the faucet), check to see if it is clogged. Unscrew the top cap and see if there is anything blocking inside. Note: If there is no air gap installed, the dishwasher might not drain properly.

If the drain hose is clogged, the dishwasher would not drain. If there is an air gap installed, it is very common that a hose going from the air gap into the garbage disposer is clogged. Remove and clean the hose. Make sure to reattach the hose before starting the dishwasher.

Note: If you recently had a garbage disposer installed, it is common to overlook removing the drain plug.

2. Broken belt
Some dishwasher models use a belt to drive the pump. Replace the belt if found broken.

Note: Sometimes the belt would just come off the pump. Even though it might not be broken, it is recommended that you replace the belt, because it is probably too stretched out.

3. Pump
Some models have two impellers inside the pump - one, wash impeller, takes care of the wash cycles, the other, drain impeller, drains the water out. If the drain impeller is broken (broken blades, shaft), the dishwasher would not drain. Replace any broken pump components.

4. Drain solenoid
Some models (for example most GE dishwashers) use a drain solenoid to drain water out. Sometimes the solenoid gets stuck, preventing the water from draining out. Try to free up the solenoid. If unsuccessful, you might have to replace the pump assembly.

5. Motor
If the motor is stuck, it is sometimes possible to free it up by manually spinning the motor.

Replace the motor if defective.

6. Timer
Replace if defective (note: uncommon problem).

Jul 27, 2009 | Dishwashers

1 Answer

Leaking dishwasher


If your dishwasher leaks, check these:Main tub seal
Door gasket or seal
Water-inlet valve
Hoses

Main tub seal
Note… If the main motor of your dishwasher is mounted vertically, beneath the center bottom of the dishwasher, the following instructions probably apply to you. But if your motor is mounted horizontally, the pump isn't serviceable--you need to replace the entire pump and motor assembly.

The main tub seal is beneath the drain impeller. It prevents the water in the dishwasher from leaking out near the shaft of the motor. To get to the seal, which is inside the dishwasher, remove the:

1. Lower rack
2. Spray arm
3. Spray arm support
4. Wash/drain impellers


Then pry the seal out of its housing and replace it.


Door gasket or seal
Over time, door gaskets and seals harden and lose their ability to seal properly. You can't repair the seals. You need to replace them if they've begun to leak. 


Water-inlet valve
The water-inlet valve, itself, seldom leaks. But, the water-supply line from the house and the rubber tube leading from the valve to the inside of the dishwasher may leak. Tighten or repair/replace these as necessary.

The water-inlet valve could mechanically stick open. When that happens, the water continues to flow into the dishwasher, which then floods your kitchen. Turn off the water supply to the dishwasher, and replace the valve.

Hoses
Behind the lower access panel on your dishwasher are several rubber or plastic hoses. If the leak appears at a connection, try a new clamp. If that doesn't work, replace the hose.
thanks for using FixYa

Feb 05, 2009 | Frigidaire 24 in. PLD2850 Built-in...

1 Answer

Danby DDW396: pump leaks when in use.


If your dishwasher leaks, check these:Main tub seal
Door gasket or seal
Water-inlet valve
Hoses

Main tub seal
Note… If the main motor of your dishwasher is mounted vertically, beneath the center bottom of the dishwasher, the following instructions probably apply to you. But if your motor is mounted horizontally, the pump isn't serviceable--you need to replace the entire pump and motor assembly.

The main tub seal is beneath the drain impeller. It prevents the water in the dishwasher from leaking out near the shaft of the motor. To get to the seal, which is inside the dishwasher, remove the:

1. Lower rack
2. Spray arm
3. Spray arm support
4. Wash/drain impellers


Then pry the seal out of its housing and replace it.


Door gasket or seal
Over time, door gaskets and seals harden and lose their ability to seal properly. You can't repair the seals. You need to replace them if they've begun to leak. 


Water-inlet valve
The water-inlet valve, itself, seldom leaks. But, the water-supply line from the house and the rubber tube leading from the valve to the inside of the dishwasher may leak. Tighten or repair/replace these as necessary.

The water-inlet valve could mechanically stick open. When that happens, the water continues to flow into the dishwasher, which then floods your kitchen. Turn off the water supply to the dishwasher, and replace the valve.

Hoses
Behind the lower access panel on your dishwasher are several rubber or plastic hoses. If the leak appears at a connection, try a new clamp. If that doesn't work, replace the hose.
thanks for using FixYa

Jan 11, 2009 | Danby 22 in. DDW396 Free-standing...

2 Answers

Leaking water from front of door


I replaced the seal part # 154576501. The notch is on the right facing the dishwasher. Just pull it out and insert the new one.
I've fought this problem for over a year, thinking it was an adjustment. I am now running it through the third cycle and I am positive it fixed my leak. Also, while you have the cover off, check and trim the tie-wrap around the wire loom. Mine was interfereing with the seal, but the seal was also slightly distorted allowing the splash to come underneath.
BnoGno

Nov 16, 2008 | Frigidaire 24 in. FDB1050REC Stainless...

1 Answer

Dishwasher Leaking


hi there,
dishwasher leaking might be due to either of these causes, check these:

Main tub seal
Note… If the main motor of your dishwasher is mounted vertically, beneath the center bottom
of the dishwasher, the following instructions probably apply to you.
But if your motor is mounted horizontally, the pump isn't serviceable--you need to replace the
entire pump and motor assembly.

The main tub seal is beneath the drain impeller. It prevents the water in the dishwasher from
leaking out near the shaft of the motor. To get to the seal, which is inside the dishwasher,
remove the:

* Lower rack
*Spray arm
* Spray arm support
* Wash/drain impellers

Then try the seal out of its housing and replace it.

Door gasket or seal
Over time, door gaskets and seals harden and lose their ability to seal properly.
You can't repair the seals. You need to replace them if they've begun to leak.

Water-inlet valve
The water-inlet valve, itself, seldom leaks. But, the water-supply line from the house and the
rubber tube leading from the valve to the inside of the dishwasher may leak. Tighten
or repair/replace these as necessary.

The water-inlet valve could mechanically stick open. When that happens, the water continues
to flow into the dishwasher, which then floods your kitchen. Turn off the water supply to the
dishwasher, and replace the valve.

Hoses
Behind the lower access panel on your dishwasher are several rubber or plastic hoses. If the
leak appears at a connection, try a new clamp. If that doesn't work, replace the hose.

Aug 27, 2008 | Kenmore 16602 / 16604 / 16609 Built-in...

1 Answer

Leaking water


hi there,
dishwasher leaking might be due to either of these causes, check these:

Main tub seal
Note… If the main motor of your dishwasher is mounted vertically, beneath the center bottom
of the dishwasher, the following instructions probably apply to you.
But if your motor is mounted horizontally, the pump isn't serviceable--you need to replace the
entire pump and motor assembly.

The main tub seal is beneath the drain impeller. It prevents the water in the dishwasher from
leaking out near the shaft of the motor. To get to the seal, which is inside the dishwasher,
remove the:

* Lower rack
*Spray arm
* Spray arm support
* Wash/drain impellers

Then try the seal out of its housing and replace it.

Door gasket or seal
Over time, door gaskets and seals harden and lose their ability to seal properly.
You can't repair the seals. You need to replace them if they've begun to leak.

Water-inlet valve
The water-inlet valve, itself, seldom leaks. But, the water-supply line from the house and the
rubber tube leading from the valve to the inside of the dishwasher may leak. Tighten
or repair/replace these as necessary.

The water-inlet valve could mechanically stick open. When that happens, the water continues
to flow into the dishwasher, which then floods your kitchen. Turn off the water supply to the
dishwasher, and replace the valve.

Hoses
Behind the lower access panel on your dishwasher are several rubber or plastic hoses. If the
leak appears at a connection, try a new clamp. If that doesn't work, replace the hose.

Jun 30, 2008 | GE GSD1180X Dishwasher

1 Answer

Leaking Dishwasher Help!


hi there,
dishwasher leaking might be due to either of these causes, check these:

Main tub seal
Note… If the main motor of your dishwasher is mounted vertically, beneath the center bottom
of the dishwasher, the following instructions probably apply to you.
But if your motor is mounted horizontally, the pump isn't serviceable--you need to replace the
entire pump and motor assembly.

The main tub seal is beneath the drain impeller. It prevents the water in the dishwasher from
leaking out near the shaft of the motor. To get to the seal, which is inside the dishwasher,
remove the:

* Lower rack
*Spray arm
* Spray arm support
* Wash/drain impellers

Then try the seal out of its housing and replace it.

Door gasket or seal
Over time, door gaskets and seals harden and lose their ability to seal properly.
You can't repair the seals. You need to replace them if they've begun to leak.

Water-inlet valve
The water-inlet valve, itself, seldom leaks. But, the water-supply line from the house and the
rubber tube leading from the valve to the inside of the dishwasher may leak. Tighten
or repair/replace these as necessary.

The water-inlet valve could mechanically stick open. When that happens, the water continues
to flow into the dishwasher, which then floods your kitchen. Turn off the water supply to the
dishwasher, and replace the valve.

Hoses
Behind the lower access panel on your dishwasher are several rubber or plastic hoses. If the
leak appears at a connection, try a new clamp. If that doesn't work, replace the hose.

Dec 12, 2006 | KitchenAid 24 in. KUDI02FRSS Stainless...

Not finding what you are looking for?
Dishwashers Logo

Related Topics:

472 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dishwashers Experts

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

yadayada
yadayada

Level 3 Expert

70374 Answers

Brad Brown

Level 3 Expert

15119 Answers

Are you a Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...