Question about Asko T780 Dryer

1 Answer

RESET BUTTON TRIPS

AFTER IT HEATS UP THE RESET BUTTON TRIPS
I HAVE TAKEN IT ALL APART AND CLEANED EVERWHERE
STILL DOES IUTR
HELP
CAN,T FIND A NEW RESET BUTTON OF WHICH I THINK IT IS
THANKS
JOHN

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

If i read everything there is another reset button in the center of the back of this model that needs to be reset.There are also 2 areas lint can build up. front lint trap and somewhere else. Good luck

Posted on Jul 01, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Whirlpool dryer heats and tumbles but doesn't dry


Sounds like it is still clogged up. Is the blower running?

Feb 23, 2014 | Whirlpool Dryers

1 Answer

My dryer won't start, when you press the start button it just clicks ? Help


what's the brand name and model number?if the dryer hasn't been cleaned out most likely you have a bad thermal fuse or high limit thermostat.if the dryer is clogged with lint and it should be pulled apart and cleaned out at least once a year the air isn't moving the dryer heats up and pops the t-stat or thermal fuse as a safety.send model number and we'll see what we can do.if you don't have a volt meter most likely you'll need to call someone in to look at it for you.

Oct 07, 2013 | Dryers

1 Answer

Aeq6700fso dryer dryness button won't change the


E68 is a stuck button on th control panel

Nov 06, 2012 | Dryers

1 Answer

The unit just stopped heating and drying the clothes.The burner on my LP Kenmore dryer won't light, otherwise everything else works just fine. I've have taken everything apart and cleaned out all...


Generally, with a gas dryer, there is an ignition device that heats to a specific temperature and this causes the gas to ignite. When this electric ignition fails to work, the gas will not ignite and there will be no heat. I had this happen and had to call a professional. It was a simple matter of installing a new ignition device and it worked perfectly for years. I hope this helps! If it is a new dryer, check to see if this part might be covered under warranty

Jul 28, 2011 | Kenmore Dryers

2 Answers

No heat....cleaned filter, vacuum etc....read about a 'reset' buttom, took off back panel, but do no see one......Is there a 'red' reset buttom? thanks


Hello, Welcome to FixYa.

There is indeed a reset or hi-limit as it is sometimes referred to on the element/heater box at the back and it should have a red button in the center you can physically push with Bosch...at least the "nexxt" series.

To start...


**Unplug the dryer before attempting any repair tips suggested here please...safety first**

If you`ve already taken the back of the dryer off to gain access you should have no problem. If you never have, it`ll take some time.

For resetting the hi-limit cut out, you can see through the back vent opening when the vent is removed and then by pushing the red button in...shown below

i.e.

923283f.jpg
Keep me posted how you make out or if anything is not clear.

Thanks for choosing FixYa and good luck. Please take a moment to rate the assistance provided here for you and a brief testimony on your experience here at FixYa is appreciated as well.

Regards,

Macmarkus :)

Jun 11, 2011 | Bosch Nexxt 500 Dryer

1 Answer

Whirlpool gas dryer WGD5540SQ it is getting power, drum does not turn, just hums when I push start button. I checked for blown circuit breaker, i' ve cleaned lint tray and checked vent to outside. I've...


there is a reset button on the motor more then likely it tripped, there are actually two one resets the other trips, but here is a website it will help with the dissemblance of the dryer, Tim:

http://www.partselect.com/dryer+dryer-wont-tumble+repair.htm

Oct 19, 2010 | Whirlpool WED5520SQ Gas Dryer

1 Answer

Dryer runs and heats about 8 min in it trips the breaker


This sounds like there is a partial clog in the air vent causing the element to get hot and sag, and/or warp the housing causing a short. The vent needs cleaned and the element probably replaced.

Jan 16, 2010 | Kenmore Dryers

1 Answer

Dryer not tumbling


A broken belt is very common. If you hear the motor running, that's probably it. The dryer must be taken all apart to replace the belt. Hopefully instructions will come with the new belt. Routing the belt over the motor shaft and around the tensioner is always a challenge.

Apr 22, 2009 | Candy CDV262 Dryer

1 Answer

Not heating


The reset button needs to be replaced.  Once it has tripped, it loses it's setting and will trip at a much lower temperature.  This is a standard procedure that LG is telling all their techs to do.

Mar 24, 2008 | LG DLE2532W Electric Dryer

Not finding what you are looking for?
Dryers Logo

Related Topics:

1,796 people viewed this question

Ask a Question

Usually answered in minutes!

Top Asko Dryers Experts

Tim Whalen

Level 3 Expert

3056 Answers

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

yadayada
yadayada

Level 3 Expert

61037 Answers

Are you an Asko Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...