Question about JVC AV-56WP30 56" Rear Projection Television

1 Answer

TV won't turn on

I woke up this morning and the power switch blinks on and off and when I turn on the direct tv box is makes a clicking noise? Any suggestions?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 472 Answers

Sounds like you have had a powersurge during the night.
The power supplies on both units will have to be inspected and repaired. The expense for this type of thing can grow rapidly depending on how much damage has been done.

Check your other appliances and see if they are all OK like the washing machine other tv's etc.

If there was any kind of storm activity during the night it could have also been a lightning strike to the antenna.

Hope that helps.

Posted on Apr 11, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My HL-P5063W won't power on. I replaced the Digital Video Board and the lamp. When I power up the the TV, there are several clicks and never a picture. The lamp does not appear to getting any...


Did u ever replace the Ballast board for this tv?No?,that ur tv problems.The Ballast board only job are to ignite the tv projection lamp to make it work.U hearing multiple clicks,lamp never ignite up the Ballast board.

Jul 29, 2011 | Samsung HL-P5063W 50" Rear Projection HDTV

1 Answer

TV will not turn on-- clicking noise in the back


The power pack the the power cord goes into has gone bad and needs replaced, see manufacturer for service or parts.

Nov 15, 2007 | Panasonic PT-50LC13 50" Rear Projection...

1 Answer

My Sony KDS-60A2000 is 41/2 years old. About 2 weeks ago I could not get the tv to power up. the green stand by light just kept blinking. I powered off, then powered up again and the tv started and and...


Hi,
TV needs lamp replacement as existing lamp got weak or has been reached to end of its working life, please note that lamp is not dead or broken so that is why lamp lit is not lit at tv front.
Hope these info will help you.
Thanks.

Nov 03, 2010 | Sony KDS-60A2000 60" HDTV

1 Answer

Tv will not turn on


its a clicking of switching relay. cannot power on due to power supply failure.

May 30, 2009 | Sony KP-48S70 48" Rear Projection...

2 Answers

Continued from no picture no sound just clicking


The TV is on protect mode. The clicking sound is the protection switch that keep turning the TV off to prevent further damage, this happens when a fault had been detected.

Try first leaving the TV power cord unplugged for some times, let say one hour or so.

Also ensure that the fault is not coming from a faulty receiver box sending bad signal, check if you get same problem with no receiver box or dvd connected.

If that does not work, and you keep having a flashing led on front of the TV, and tv turning off by itself after a while, that indicates a fault condition.

The flashing light indicates a diagnostic state called protection.
When the TV goes on protection there are only two possible reasons.

1The internal circuits are jammed because of electrostatic charges accumulating on capacitors, or because of a wrong voltage read by the main chip on your monitor controller board. this started the protection circuit.

2 The protection circuit detected a wrong voltage or abroken contact, identified an internal fault and kicked in , startingthe flashing light.


If you are in situation one, then theTV will reset just unplugging power cord for one or two hours,sometimes even minutes.

If you are in situation 2 , then there is an internal fault.

Common faults that can occur are a blown capacitor on power board, a convergence IC has blown, or a fault on Digital board.

Check also the video cable or any external connection cable, if the cable is shorting, or the connector is bad, you can get same flashing state because of the video cable.


If under warranty contact the manufacturer ringing the number on the user manual

If you want to repair at your own expenses, just locate any good qualified repairer.

If you want to DIY you find parts here,

Appliance parts, electronics parts & more from PartStore.com

Encompass Parts Distribution

Electronic Replacement Parts: Plasma & LCD TVs, Appliances |

May 15, 2009 | Hitachi 53UDX10B 53" Rear Projection...

1 Answer

Sony grand wega KF60DX100 Won't Power on


THE RED LIGHT THAT BLINKS IS IT THE LAMP BOX THAT THE RED LIGHT BLINKS IN OR THE STAND BY LIGHT THAT BLINKS ? IF ITS THE LAMP BOX THAT BLINKS THEN YOUR LAMP HAS BLOWN AND NEEDS REPLACED YOU CAN FIND THE PART # FOR YOUR T.V. FOR A NEW OR REFURBISHED LIGHT IN YOUR OPERATING MANUAL AND WITH THE PART # BUY A NEW ONE OFF EBAY,ALSO YOUR OWNERS MANUAL WILL GIVE YOU STEP BY STEP INSTRUCTIONS ON HOW TO REPLACE IT AS THIS IS A COMMON PROBLEM WITH PROJECTION T.V.'S IF ITS THE STAND BY LIGHT THAT BLINKS I NEED TO KNOW HOW MANY TIMES IT BLINKS AS THAT'S A SELF DIAGNOSTICS CODE THAT YOUR T.V. IS GIVING FOR THE PROBLEM AND FOR SONY THERESE NO CODE FOR 1 BLINK OF THE STAND BY LIGHT.

Mar 16, 2009 | Sony Grand WEGA KF60DX100 60" Rear...

1 Answer

Need code to program remote to work with Direct TV brand box.


I have the codes you need to set direct handunit for your TV.11145-10145-11960-11904-11445-11345-11045-10797-10583-10577-10413-10409-10279-10227-10173-10151-10097-10095-10056 10038-10032-10016-10105 Switch slide mode to TV make sure tv is on now press and hol MUTE&Select together untill it flashes green now enter code then press power if set turns off that will be your code if not repeat steps untill TV powers OFF.

Jan 10, 2009 | Hitachi 51UWX20B 51" Rear Projection...

1 Answer

No power to the television


Dont know if this will help, try leaving it unplugged over night, thaught I saw that solution in a blog somewhere a while ago.

Dec 23, 2007 | Akai PT5598HD 55" Rear Projection...

Not finding what you are looking for?
JVC AV-56WP30 56" Rear Projection Television Logo

Related Topics:

67 people viewed this question

Ask a Question

Usually answered in minutes!

Top JVC Televison & Video Experts

The Knight
The Knight

Level 3 Expert

69845 Answers

easy alberta
easy alberta

Level 2 Expert

132 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a JVC Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...