Question about Maytag Performa PAV2200

1 Answer

Dishwasher not cleaning well

My Performa dishwasher does not seem to have enough water pressure to clean properly.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 868 Answers

How hot is the water ;120 is the minimum it should read at.If its below 120 than look for either a bad heater element or turn up the water heater.Rinse Aid needs to be added if its out.

Posted on May 23, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My dish washer wont fill with water


there is a float, usually at front left side inside dishwasher, that may be stuck..possibly an utility holding it up, or the fill valve is stuck. When dishwasher calls for water, it fills until this float rises to proper level and shuts the valve off at proper level. If it sticks, water will shut off at improper level.

May 01, 2014 | Zanussi FS1255S Front Load Washer

1 Answer

Spots are left on the dishes after washing. Dishes don't look clean


Hi

If you are noticing that the dishes are not clean, then there are a few things to check for. Check the soap powder if it's kept in a dry environment. Also try replacing the powder with something like a gel or liquid. Next thing to check for is the water pressure and fill valve. Check if the water is filling in and the spray arms are throwing the water with enough pressure. Try and listen to the sound if you hear a proper spraying action sound.

If it seems as a low water pressure then check the fill valve. Now, check if dishwasher is draining the water or not. While the dishwasher is working check whether the dishwasher is draining and there is not much left out water after the cycle is complete. Try cleaning the spray arm with a soft brush. The water temperature plays a major role in cleaning of dishes. The temp should be between 125 and 150 F for dishwasher to clean the dishes. Hope this helps...

Daniel

Nov 26, 2010 | Kenmore Washing Machines

1 Answer

My Maytag Performa washer loves to flood the house!!!!


sounds like pressure switch is bad or pressure hose is plugged or water valve is bad or drain overflowing

Apr 22, 2010 | Maytag Performa PAV2200

1 Answer

My maytag dishwasher does not have enough pressure to drive the water through the wands onto the dishes. I have cleaned the screen underneath the bottom wand but this has not increased the pressure enough....


I would check to see if you have enough water in the dishwasher. Let the dishwasher fill with water and set the spray arm in a positoin you will remember where it is.
Take a large pot of hot water and add it to the dishwasher and close the door. Start the dishwasher and observe to see if the spray arm moves.
If it moves you may have to change the water inlet valve. It may be restristing the water flow into the dishwasher.
The water inlet valve is located behind the lower kick panel.(4) screws, Remove the panel and see where the water pipe hooks into the water inlet valve. Remove two wires and two screws. Shut water off and remove the water line going into the valve and the small rubber hose coming out of the valve.
Replace valve and reinstall kick panel.
Hope this helps.

Dec 31, 2009 | Washing Machines

1 Answer

Our model GHW9100LW1 Duet Whirlpool Front Load Washer has an intermittent H-F code,beeps and stops. Seems like it's worse with winter coming...20's to 40's outside...input water too cold or not enough...


H and F code flashing alternately could be one or more of the following items not working properly or bad:

- Flowmeter.
- Water inlet valve
- Water pressure switch. (last thing to replace)

Make sure to unplug power cord before you replace the part and also make to clean drain tube and filter every year.

Nov 29, 2009 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

My Maytag Performa Dishwasher is leaking when doing the dishes...


Sounds like your fill valve is stuck in the filling position...see if you you have water standing in it a couple hrs after a drain cycle. if it does then the valve needs to be replaced or you can take it apart carefully,(there is a sping that might fly out and get lost) and clean it. Mine had some small trash in it from the city water line.. The left side has an over flow hole is where your water is coming from..

Nov 12, 2009 | Maytag Performa PAV2200

1 Answer

Maytag washer overfilling


Easy fix. Do this: Remove the rubber tube coming from the bottom of the tub up to the water level switch right there at the switch itself. Blow through it to remove the sediment in the bottom of the tub so that air pressure from tub to switch will be kosher. Put the hose back on the water level switch tight and pump out any water in the machine.
Retry

9ec91a6.jpg

Dec 19, 2008 | Maytag Performa PAV2200

1 Answer

I have a karcher 411 A jet washer, there doesn't seem to be enough pressure to do the job. I have bought a new wand but it doesn't seem to make any difference, any ideas, what am I doing wrong


Check to see if there's good water volume coming through the hoses attached to the washing machine. If there is, check to see if the screens inside the water-inlet valve are clean. (The water-inlet valve is the device on the washing machine that the fill hoses are attached to.) If they're clean, you probably have a defective water-inlet valve. If so, you should completely replace the valve.

Aug 31, 2008 | Washing Machines

1 Answer

Hotpoint WM64 doesnt seem to be taking in enough water


Close your faucet valve & unscrew your hoses to check screens on hoses & machine. Clean out well. Refit, check for leaks. Water shd be in good pressure. If this is not the problem change your inlet valve, it is easily done. Suggestion: use powders for front loaders.

May 08, 2008 | Hotpoint WMA32 Front Load Washer

2 Answers

Maytag performa dishwasher pdc3600awx


Home depot sells the faucet adaptor you need. It is called "Long Dishwasher Aerator" and states 55/64 " - 27 thread. The number on the top left which I suppose is the part number is 36094B. It also has a yellow stick with "2A" on it, which should help find it quickly. It is located in the section where they have all the kitchen faucet aerators etc. Found it easily. Cost was $3.77

Mar 30, 2008 | Maytag Performa PAV2200

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

152 people viewed this question

Ask a Question

Usually answered in minutes!

Top Maytag Washing Machines Experts

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Al Clark

Level 2 Expert

290 Answers

Todd Marr
Todd Marr

Level 2 Expert

77 Answers

Are you a Maytag Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...