How do you enter a pnone number on the phone directory

Pnones are different. Procedure might be different from make and model so you should fin the proper user's manual for your UNSPECIFIED make and model.
Do a Google search for terms

MMANUAL, MAKE AND MODEL OF YOU PHONE.

It will dial whatever you have entered --- if a 1 is needed
at the keypad, a 1 is needed to be stored in the directory
listing of the number.

I use the "10-10-987" service and have entered those
numbers into the directory entries, 'works fine.

Good luck!

Try adding your voice mail access number into the directory of the KX TG2770. You will need to enter the number separately for the base and the handset or copy it from the base to the handset. On the base, press Conf/Edit. Then navigate (up/down arrows) to Save Directory. Once in this submenu, you'll be able to add a name and phone number.

Then to call the access number, go to the directory list and locate the name/number and call it.

Panasonic has the manual for your phone here: http://service.us.panasonic.com/OPERMANPDF/KXTG2770S.PDF . See page 33 and the following pages.

I hope this helps.

Cindy Wells
(Other phones have a voice mail waiting icon and let you program that number outside of the directory. These also check if you have voice mail waiting for the line that they are connected to. This phone doesn't seem to have that ability.)

The system directory sits in system program 001. It's access from the control phone, usually the first one in the system (101) and from there you press PROG **1234 and dial 001 ENTER If you keep pressing ENTER it will step through the numbers from 001 to 999, or between the first and second ENTER you can dial a 3-digit number. EXIT a few times or pick up the handset and drop it back down exits programming.


Carl

Enter the model of your VTech phone into the search box at
http://www.vtechphones.com/vtechphones/index.cfm/support/general/manuals/
to get the manual.

Using the Call Log or Directories
You can make a call with the call log or directories as follows:
Outgoing Call Log
Incoming Call Log
Extension Number Directory
System Speed Dialing Directory
Personal Speed Dialing Directory
Calling with a call log or directory
While on-hook
>Press Left or Right
until desired log/
directory appears.
>Press ENTER.
>Press Up or Down until
desired item appears.
>Off-hook
To cancel or exit, press cancel or exit.
Clearing the log information
>While confirming the log information
>Press Up or Down until
desired item appears.
>Press "CLEAR".
Storing the caller's information for the Personal Speed Dialing Directory
>While confirming the log information
>Press Up or
Down until
desired item
appears.
>Press STORE or
ENTER.
>Press STORE or
ENTER.
>Press "EXIT" or
PAUSE.
To enter characters, refer to "Entering Characters".

to program the directory on a 12 button handse;

Press the TSFR key

Enter 200

Enter code 1234

=/- key to enable

Speaker key

Your next command will be the MMC required.

To program the system speed dial directory

Enter 705 - Speed dial 12th Button down to toggle between

Enter 706 - Speed Name the 2 MMC

If it is the factory set pin, most likely it will be 0000. Could also be 1234 if you have tried the first. Tesco really needs to take the responsibility here and get your phone unlocked for you. Its not something the average person can do. I would ask for the manager and tell him what is going on. If that doesn't work call the corporate office. They can give you the #.

To program the personal directory Its diferent to program the system directory. the personal has 8 number capaciti and the system has 999 number. To program the System directory
1.- Enter to PBX program mode from your station 101
2.- Choose program 001 to enter the quick dial numbers
3.- Choose program 002 to enter (Or change ) the Labels

I assume you have the manual. I found it very difficult to follow, very poor. While "on hook" enter the number you want to call. Press "store" or "enter". Enter the name referring to the graphics chart on pages 7 & 8. It is set up for Alpha characters and it depends on which software is installed on your phone. Example: If you want the letter "A" you press the number 2 one time. If you want the number "2", you have press "2" seven times to display the number 2. Use the toggle key to move to the next letter or number you want to enter. When you have finished press "Store". It may take awhile but that's how its done. Not a very good system for the average consumer in my opinion. But that's how its done. I was unable to upload the manual. Here's the link if you don't have it: http://www2.panasonic.com/consumer-electronics/support/Phones-Fax/Business-Home-Systems/System-Phones/Digital-Hybrid-IP-PBX-Phones/model.KX-T7630