Question about Canon PIXMA MP600 all-In-One InkJet Printer

3 Answers

ERROR U130 I've a MP600. After charging the magenta tank, this message was shown "the remaining level of the followng ink cannot be correctly detected. replace the ink tank". The orange light on the printer is on and the tank flashing too.

Posted by on

  • 2 more comments 
  • bones3 Apr 11, 2008

    i have this error too u130 after replacing the magenta tank . have you replaced with a copy tank where you have too swap the chip over??

  • soerensen Apr 14, 2008

    I Have the same problem, can some one help me how to move.

  • elevator5 Jan 16, 2009

    same message.... although there is a full black #5 ink source.....it will not print and claims it cannot correctly detect the ink

  • Anonymous Mar 18, 2014

    i have replaced three ink tanks but an error message appears saying i have more than one tank of the same colour. this is not the case

×

3 Answers

  • Level 1:

    An expert who has achieved level 1.

    Governor:

    An expert whose answer got voted for 20 times.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

The remaining ink level cannot be correctly detected. Replace the ink tank and close the Scanning Unit (Printer Cover). Printing with an ink tank that was once empty may damage the machine. If you want to continue printing in this condition, you need to release the function for detecting the remaining ink level. Press and hold the Stop/Reset button for at least 5 seconds, and then release it. * With this operation, releasing the function for detecting the remaining ink level is memorized. Please be advised that Canon shall not be liable for any machine malfunction or damage caused by refilled ink tanks. See “Replacing an Ink Tank” on page 46.

Posted on May 11, 2008

  • Lawrence Fieman Dec 15, 2010

    Very helpful for we ReInkers. I have a chip-resetter, but the battery ran down. THis is a good interm fix.

×

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I have the same problem w/ error u130 on my Canon MX700. I bought the wrong ink even though they all say the same cartridge 8 blue. look at the model number in fine print. goto canon's website for your specific ink. i want to thank my brother for solving this error. Trust me, read the fine print!

Posted on Mar 13, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Yes the chip i swap over

Posted on Apr 14, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi, I refilled cartridge CLI-526M fromCanon Prixma MG5250 and I have the error U130. How can I resolve the error to reprint? Thanks.


FAQ: An Error Message Is Displayed on the LCD

Issue

If an error message is displayed on the LCD, take the corresponding action described below.

Cause
The following ink may have run out. Replacing the ink tank is recommended. U041 Print head is not installed.Install the print head.U051 / The type of print head is incorrect.Install the correct print head.U052 Some ink tanks are not installed in place. U072 / More than one ink tank of the following color is installed. U071 The remaining level of the following ink cannot be correctly detected. Replace the ink tank. U130 The following ink tank cannot be recognized. U043 U140 U150 The following ink has run out. Replace the ink tank. U163 There are no photos in memory card Contact the support center or service center for ink absorber replacement. Press OK to continue printing Ink absorber full. Service required Timeout error has occurred The device may be incompatible. Remove the device and check the manual supplied with the connected device An unsupported USB hub is connected. Remove the hub. B200Printer error has occurred. See the manual **** Printer error has occurred. Turn off power then back on again. If problem persists, see the manual

Jul 06, 2011 | Canon MG5250 Printer

1 Answer

U130 ink message on pixma mp620


Very simple solution: When the pixma mp620 screen shows error U130, Hold down the stop (red triangle) key for about 7 - 10 seconds. This overrides/turns off the ink monitoring function. The printer will begin "thinking" for a bit and then start printing. Note: you may have to do this seperately for each color. You'll also notice that when the lid is open and the cartridges are in position for changing, the cartridges that used to be "out" are no longer flashing red, nor a stead red. They are dark.

Feb 17, 2010 | Canon PIXMA MP620 All-In-One InkJet...

1 Answer

This is for iP4600


You either replace the magenta cartridge, the chip on the cartridge, or hold the resume button for 5 seconds or more.

Aug 27, 2009 | Cannon Canon i960 Photo Printer

2 Answers

MP500 ink tank cannot be recognized error U043


I had the same problem. My mp630 is also only 4 months old. I replaced all colour ink cartrdiges(inc black), but was only able to release the function for detecting the ink levels for magenta and cyan. Yellow and black then started giving error message U043, with them alternating between working, but never working at the same time. Getting them all clicked in with the lights glowing red does not solve the problem, as once the printer cover is closed, the same error message turns up. The only thing that worked for me is moving the chip slightly out of alignment, by pushing the sliding chip holder, and I only had to do this twice before they all started working and the printer was unlocked.

Jul 30, 2008 | Canon PIXMA MP600 all-In-One InkJet...

2 Answers

Ink cartridge


clean the contacts of the inkcartridge chip e.g. with spirit
or
Press the reset/stop-button for >10s to quit the error ... but be aware that the ink level will no longer shown correctly

May 15, 2008 | Canon PIXMA MP830 All-In-One InkJet...

1 Answer

Charging Ink Tank


same as azin i changed the black tank and the chip but it now prints everything except black

Apr 10, 2008 | Canon PIXMA MP600 all-In-One InkJet...

2 Answers

MP500 ink tank cannot be recognized error U043


Same problem - two solutions I found helped me work out mine. One said contacts needed to be cleaned and it worked to use a Q-tip and alcohol or just click it in position several times until it recognizes the cartridge - this may work. Another said that they got it to work by installing a brand new cartridge - cool, but I have one full of ink it won't recognize. So I pulled the little circuit board off a used cartridge (like you need to do with some refills) and put it on the cartridge that it wouldn't recogrnize - works great. Still haven't figured out how to get it to acknowledge ink levels though. Canon really should be more consumer friendly since these problems seem to be intended to compel the use of proprietary cartridges.

Dec 27, 2007 | Canon PIXMA MP600 all-In-One InkJet...

4 Answers

"ink cannot be correctly detected" error U130


Hold down the "Stop/Reset" button for 5 seconds and it dismissed the first message, but then there was another for a different cartridge, etc. Eventually I got it to work.

Jul 26, 2007 | Canon Pixma MP800 All-In-One InkJet...

3 Answers

Refilling Ink in Canon Pixma MP830


Hello, I found this in a repair manual for the MP830. summery is to press and hold the stop/reset button for 5 or more seconds. I copied the info from the manual too. The remaining ink amount unknown. [1683] (Applicable ink tank icon) The remaining level of the following ink cannot be correctly detected. An ink tank which has once been empty is installed. Replace the applicable ink tank with a new one. Printing with a once-empty or refilled ink tank can damage the print head. If printing is continued without replacing the refilled ink tank, press the Stop/Reset button for 5 sec. or longer to record the use of a refilled ink tank. Note: After the above operation, the function to detect the remaining ink amount is disabled.

Jul 17, 2007 | Canon PIXMA MP780 All-In-One InkJet...

Not finding what you are looking for?
Canon PIXMA MP600 all-In-One InkJet Printer Logo

4,115 people viewed this question

Ask a Question

Usually answered in minutes!

Top Canon Office Equipment & Supplies Experts

kakima

Level 3 Expert

98879 Answers

old marine
old marine

Level 3 Expert

1573 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Canon Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...