Question about Mitsubishi WS-48613 48" Rear Projection Television

2 Answers

Colors are offset

The colors on my tv are off by about 3 inches on the left and only about 1/2 inch on the right. I have tried to configure the colors in the menu but it doesn't seem to help. what is wrong. What parts do i need to fix this?

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

The colors on my mitsubishi 50in model number vs-5041 are foggy and halo-ed....the blues look gray and the reds and green are too bright and seem to bleed into the other colors. What is wrong with my tv and how do i fix it?

Posted on Sep 16, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Mitsubishi Master
  • 8,617 Answers

You will need to install new convergence ICs if you need more info on this please let me know. Its a fairly easy repair.

Posted on Apr 10, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Flash Focus does not correct convergence problem and i cannot manually adjust the red convergence to proper alignment. Red does not move laterally only vertically. Picture is offset to the right with red...


No,any colors lines mis alignments.The tv convergence board parts are dead.The 2 STK convergence ICS and some or all it resistors are dead.These parts must be replace on the tv convergence board.To solveved convergence problems.The shop,will cost u $300-350 for parts and labors.

Aug 10, 2010 | Sony KP-51HW40 51" Rear Projection...

2 Answers

My TV looks like it had permanent 3-D. Red Ghost


hello it sound like the convergance ic may be the problem these chips sit behind the tuner board connected to a metal frame called a heat sink they are soldered in. also you will have to check the resistor in front of the chips also check the 2 capacitors at either end it would be best to get a quote from and engineer good luck

regards
shaun

Jul 10, 2010 | Sony KP-51WS510 51" Rear Projection...

1 Answer

Im having a issue with my RCA 52 inch HD tv. It is like watching in 3D everything is in 3 colors


Bad fuse FL231 it does not look like a fuse But it is ! it will be on your deflection board first bottom board to the left on right side of FBT flyback transfomer thier is 3 in a roll small brown rectrangler looking caps but they are fuses it will be the one in the middle call Mats Electronics 1-800-628-1118 for fuse.

Nov 12, 2009 | RCA D52W20 52" Rear Projection HDTV-Ready...

1 Answer

The whole blue sceen is offset to the right?


1.) If it will not adjust and it is a PT-53wx42 made by Panasonic you need to replace both of the STK-392-110 Convergence chips and any of the protect resistors around them that are damaged.

2.) The reason this kind of problem happens is the two chips are about 2 1/2 inches wide X 1 1/2 inches tall(Black in color) and the back of each chip is metal---they are mounted side by side on metal heat sinks with fins(They will have the STK-392-110 printed on them in white letters)---when they are installed a white grease is applied to the back of each chip to transfer heat quickly and keep them cool---after several years the heat sink grease dries out and the chips overheat and fail.

3.) I have done hundreds of these sets and if you have the skill you can do the repair yourself--you can buy both chips on Ebay for about 12 dollars plus shipping. I also have step by step start to finish instructions for doing this repair on this set---

4.) If you are not able to do this repair shop around in your area as most TV shops try to charge 300-400 for this kind of repair--I do them here for 200-250 in the customer's home.

5.) If a shop says it has to go to the shop--keep looking as any good tech can do this repair right in your home in about 1 hour.

6.) Once the chips are replaced and the set adjusted it should not have this problem again for 5 - 8 years--this is about the only problem this kind of set has.

7.) If you think you can do it yourself---give me a vote here and your email and I will email instructions to you----I am here to help people--even if you cannot do it yourself if you find someone who can do it for a reasonable price it is much less than the cost of a new set--these sets are much more reliable then the LCD AND PLASMA sets.

I do this here for free, so if this information has helped you give me a vote here, and if you have any questions or need advice respond to this posting here.

Regards, SD TECH

Sep 20, 2009 | Panasonic PT-53WX42 53" Rear Projection...

1 Answer

Unable to align red crosshairs in horizontal range


No there are no quick fix options for this fault. The convergence amplifiers operate similar to a high power audio amplifier, so if there is an impairment anywhere in the system, it will result in distorted audio, or in the case of television convergence amplifiers, one or more colors won't align. The convergence power pacs need to be replaced and the out of tolerance precision resistors located near the power pacs need to be carefully checked and replaced as necessary. And the power supply fuse links to the power pacs checked and replaced as needed.

It is also possible that there are root faults that cause the amplifiers to go bad which include bad connections or a bad digital control module. This repair is possible for anyone having basic electronics knowledge and soldering skills. After the above repairs are performed it may be necessary to perform the static convergence realignment procedure using the outer cross hairs as you mentioned, and realigning them.

Apr 23, 2009 | Hitachi 53UDX10B 53" Rear Projection...

1 Answer

Colors are separated on the top from the left to right


Probably the color convergence is off. I had a similar problem. Have you tried the magic focus button yet? That is located at left in the small front control panel. Power on TV, wait 20 min (according to user guide), then press the magic focus. If that doesn't fix the problem, you could try the service mode alignment procedure. But that's a little trickier. I don't have a link handy for that procedure right now, but will look for it if magic focus doesn't re-align your color convergence.

Jan 02, 2009 | Hitachi 53UDX10B 53" Rear Projection...

4 Answers

I own a samsung ln46a530 and need to configure it for the best picture.....any recomendatios?


If you haven't already bought a nice set of HDMI cables, go ahead and do so (just dont fall for the "gold plated" cables as they are a gimmick). Unfortunately, while we all want that HD quality, there seems to be some problems with the ln46a530 when switching from RCA to HDMI. On the bright side, they have been resolved in this forum post.

Best audio settings:
Mode: Custom
SRS TruSurround XT: On
Auto Volume: On
TV Speaker: On

attachment.php?attachmentid=107143&d=1207804513

(# of clicks):
Balance: 0
100Hz: 8 clicks right
300Hz: 8 left
1kHz: 4 left
3kHz: 3 right
10kHz: 5 right


For best picture:

Most accurate settings
(This with the mode at movie)
Backlight = 6
Contrast = 85
Brightness = 49
Sharpness = 0
Color = 50
Tint = G50/R50

DETAILED SETTINGS

Black Adjust = Off
Dynamic Contrast = Off
Gamma = 0
Color Space = Custom
Red: R33 - G0 - B0
Green: R18 - G52 - B0
Blue: R11 - G0 - B51
Yellow: R49 - G53 - B0
Cyan: R22 - G46 - B56
Magenta: R37 - G0 - B43
Flesh Tone = 0
Edge Enhancement = Off
Xycc = Off

WHITE BALANCE

R-Offset = 26
G-Offset = 25
B-Offset = 22
R-Gain = 30
G-Gain = 25
B-Gain = 25

PICTURE OPTIONS

Color Tone = Warm 2
Digital N/R = Off
HDMI Black Level = Low (actually it's disabled when playing Blu-ray)<-- set this according to your source! If you use a PC, or aPS3/Xbox360 with expanded RGB levels, you might need to set this tonormal!
Film Mode = off (disabled)
Blue Mode = Off

Energy Saving = Medium
Entertainment modes = Off



Hope this helps!!

Dec 01, 2008 | Samsung Projection Televisions

1 Answer

Arching color wave on bottom left corner & also on top left corner(color changes)


Convergence amps are failing which is very common. Several hundred dollars for a repair.

Dec 26, 2007 | Philips Magnavox 51MP392H Rear Projection...

1 Answer

Red colored halo at bottom corners of screen


Movement of any TV can result in a problem caused by bad
solder connections.In your case, the red convergence IC......
Found on a circuit board,mounted on large heatsinks........
Part # STK392-040.....Change both for prevent maintenance.
Do not use generics - I use OEM or better = Sam,Pan,Hitachi.
After repair,recheck alignment................T.

Nov 20, 2007 | Samsung PCJ533R 53" Rear Projection...

2 Answers

C Color is way outta wack on my 56 inch pilips rear proj tv. HELP


http://home.earthlink.net/~oleg.filippov/ConvergenceFix.htm
http://cmpalmer.blogspot.com/2006/11/fixing-my-own-tv-part-ii.html

Oct 28, 2007 | Philips 60PP9352 60" Rear Projection...

Not finding what you are looking for?
Mitsubishi WS-48613 48" Rear Projection Television Logo

109 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Projection Televisions Experts

matt martin
matt martin

Level 3 Expert

1191 Answers

Jaime Hernandez

Level 3 Expert

2267 Answers

The Knight
The Knight

Level 3 Expert

68301 Answers

Are you a Mitsubishi Projection Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...