Gradually some the phones in our office have begun to beep when the handset is lifted. It started with one and now it is three. We can't figure out what has happened to create this issue. It doesn't seem to affect the other functions, it's just incredibly annoying. Any suggestions?
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need. goodluck!
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
Disconnect AC power adapter from the back/bottom of base unit, then connect it again properly.
OR, to resolve this issue, you have to re-register the handset.
To do this on a non-expandable cordless phone: Press and hold the LOCATOR/INTERCOM button on the Base until a beep sounds. Press and hold the FLASH/CALL WAIT button on the Handset until a beep is heard. When registration is complete, a beep sounds from the handset. Wait for 20 seconds after registration is complete to allow the handset to establish communications with the base. If this fails to help: Remove the AC Adapter from the phone base or wall outlet for a few seconds and reconnect. It may also be necessary to remove the battery from the handset for a brief moment.
To do this on a expandable cordless phone system: Press and hold the LOCATOR/INTERCOM button for the extension that is displaying "No Link To Base" on the Base until a beep sounds. Press and hold the FLASH/CALL WAIT button on the Handset that is displaying "No Link To Base" until a beep is heard. When registration is complete, a beep sounds from the handset. Wait for 20 seconds after registration is complete to allow the handset to establish communications with the base. If this fails to help: Remove the AC Adapter from the base or wall outlet for a few seconds and reconnect. It may also be necessary to remove the battery from the handset for a brief moment.
Another user (thank yoiu but I'm sorry I forgot his/her name) had the answer. It was ihe instructions but I missed it. Needed to set the 2nd handset into the main base for 20 seconds so that it could align itself.
1) Call to the first party and hold the line. 2) To add new party, press CONF + 2nd party phone no, after this talk and ask the 2nd party to hold the line. 3) Press CONF again and after a beep tone, then can talk with multiple parties. 4) To leave the conference, press CONF and after beep tone, lift down the handset.
wow good question. and no change on settings. why? well this phones are fully contain system and are not a key or pbx system like the bigger office equipment. but over all it will work well and for the price I think you can bare with the beep.
Remote ring detection provides a low tone * triple beep in your
wireless headset when you receive an incoming call. This feature
requires a handset lifter accessory, such as the Plantronics HL1 or HL10. If you do have a handset lifter but do not hear the remote ring detection, please check the following:
Check the placement of the lifter. - Make sure the handset lifter positioned directly over the phone's speaker.
Try adjusting the phone's ringer volume. If the phone's ringer is too
quiet, it may not trigger the ring detection built into the lifter. Try
turning up the ringer volume of your phone.
ring tone of the phone. - If your phone's ring tone provides short
beeps or plays music, the lifter's microphone may not detect it. Try
switching your ring tone to a traditional ring or long beep.
Does the phone have different rings? - For example internal calls vs
external calls vs transferred calls. Does the phone ring the same for
each type of these calls. If so try changing so all calls use the same
Attach the optional "external ring detector"
cable. This cable plugs into the lifter and provides a small, black
microphone. It is included in the plastic bag of lifter accessories.
Mount the microphone near your telephone's speaker. Click here for more
There are 2 versions of the Lifter accessory
- HL10 and HL1. The HL1 is a larger older version of the liter with a
more sensitive rind detector. Some phones will require the older
version of the lifter.
Please view the On Line Compatibility Guide to see if the older version (HL1) will be required for your phone.
*Please note the volume of notification beep in the headset cannot be altered, it will always be a low tone triple beep .
My handset does not connect to the base station. It flashes momentarily, but does not find the base. The base station has a humming noise when the phone line is disconnected and the talk button is depressed. Hum is also present when the phone line is reconnected. The problem was resolved by replacing the 9VDC power supply. The hum disappeared and the handset immediately connected to the base.
If you have more than one phone line which I assume that you do -if one party has not completely hung up the handset after putting someone on hold when you pick it up on your end you will hear that beeping noise that you are talking about. Have them pick back up the line while you are on it and replace the handset again on thier phone to disconnect completely.
1. make sure phone is charged 2. hold down the "mute/program button on the phone 10 seconds. 3. you should see a message on the screen that says you need to push the "pager button" on the handset. 4. Push the pager button