Question about Briel Apollo ES-41BPG Espresso Machine

5 Answers

Need spare parts for Briel Apollo ES41PG

Where can I purchase . . .

1. Water exit valve, spring, Oring support and its respective parts.

2. Filter holder for ground coffee.

3. Cremaker filter for l or 2 cups

Posted by on

  • 7 more comments 
  • oliveadshead Oct 15, 2010

    DO YOU KNOW WHERE I CAN BUY A REPLACEMENT WATER EXIT VALVE, SPRING AND O RING AND RESPECIVE PARTS ?

  • oliveadshead Oct 16, 2010

    A good contact but they do not have the part I need. Many thanks.

  • oliveadshead Oct 16, 2010

    No solution as yet. Still searching for this part.

  • oliveadshead Oct 16, 2010

    Thank you, I will try this link.

  • oliveadshead Oct 16, 2010

    They do not stock Briel parts. Worth a try.

  • oliveadshead Oct 16, 2010

    Still searching. I hate to throw away the machine for the sake of one very small part.

  • oliveadshead Oct 16, 2010

    Still searching and hoping there is one of these valves out there somewhere

  • oliveadshead Oct 16, 2010

    A good site but they do not stock the part I need. Thank you for trying.

  • oliveadshead Oct 16, 2010

    Not yet ready to give up

×

5 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Expert
  • 2,973 Answers

Please follow the link below and after registering you can pose your problem to them for necessary info on your needs.
https://www.amazon.com/gp/help/contact-us/general-questions.html?ie=UTF8&browse_node_id=518316
All the best.

Posted on Oct 17, 2010

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Briel Master
  • 75,822 Answers

We have no parts resources, we are a tech support for troubleshooting only

Posted on Oct 16, 2010

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Guru:

    An expert who has written 7 tips or uploaded 3 video tips

  • Master
  • 468 Answers

Hi,

You can visit the link mentioned below:

http://www.cafeparts.com/dynamicIndex.asp

Thanks and regards,

Anil.B.R

Posted on Oct 16, 2010

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Briel Master
  • 1,711 Answers

Briel espresso machines are not so popular to sell spare parts online.

However you have one very good option, we have here below their link which they have some online parts store. However for all other additional parts you can contact them and they are more than happy to help you .

http://www.mcssl.com/store/electra-craft/catalog/category/5059886

Try them .

Posted on Oct 16, 2010

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,478 Answers

Hello,

I will advice you check ebay.com or amazon.com for the items needed.

Take care.

Posted on Oct 15, 2010

  • Jimoh Adeleke Muyideen Oct 16, 2010

    Hello,

    Check ereplacementparts.com for the parts needed.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is phone number of customer service Briel spare parts


How Do You Get Service?
If repairs become necessary or spare parts are needed, please contact via telephone at (1-800-763-6699) or via email info@electra-craft.com, or please write to:

BRIEL Service Center
250 Halsey Street
Newark, NJ. 07102Website: Service Center
What if you have questions about your machine?
You can contact our BRIEL offices via telephone at (770-509-3006) or via email brielcustsvc@smithagy.net, or write to:

BRIEL/ The Smith Agency
P.O. Box 669307
Marietta, GA. 30066-0106 Briel Limited Warranry

Nov 17, 2016 | Briel Coffee Makers & Espresso Machines

1 Answer

Shower head keeps dripping water does not stop when turned off


I would look into possible failure of the solenoid valve assembly or the valve top assembly, which are parts 8 and 7 respectively, on the linked page. This site also has all the spare parts for sale.
You are viewing shower spares for Galaxy Aqua 2000 Aqua 2000

Aug 16, 2014 | Galaxy Aqua 2000

1 Answer

Lg washer parts water pump filter


try e spares on the internet just tell them make and model

Jan 04, 2014 | Washing Machines

1 Answer

Head valve seems to stick during firing of the tool All new part in tool I have 5 tools with same problem mcn150


#1 If the gun only releases air from the trigger and does not fire, suspect orings on Headvalve leaking. Easy to check, remove head and Headvalve and examine the surface in head where oring makes contact with metal surface. If the metal surface looks worn / fine scratches, air is leaking past and gun will not fire. Remove fine scratches with 400 grit paper. Headvalve oring must seal or gun will not fire. If the Headvalve does not make tight seal with new oring, remove new oring and wrap some teflon tape into groove and reinstall oring. The teflon tape will make the oring fit tight against metal surface (try 1 1/2 loops of tape).
#2 If the gun fires however the headvalve gets stuck in the head after some use, Headvalve spring could be weak. Replace the spring or remove the spring and add spacer below spring to give more pressure (I use oring with same diameter as spring under the spring ).
Use silicone paste lube on all orings and surface where orings make contact. This paste is sold at Lowes in the plumbing department and swimming pool supplies. When you connect air to the gun, listen carefully for leaks out the nose or head. Slight leaks will affect how the gun works. Repair as needed. Good luck with your repair.

May 23, 2011 | Stanley Bostitch Mcn150 Strapshot Metal...

2 Answers

Duofast ms 7664c staple gun still blowing air out


This series of nailers are the most difficult to repair. Your nailer has twice as many orings as the norm. Many have said that this nailer is over-engineered. There are three areas that could cause trigger area leak. To make it simple, lets do one area at a time. Use soapy water around the trigger area to find actual leak. If air is leaking from actual trigger valve (ms719-2) and its counterpart, the cartridge (ms719-1) then these two parts need to be removed. Check for scratches in the metal of the valve. If scratched try to remove with fine paper or replace as necessary. Most leaks are due to faulty trigger valve. If air is not leaking from actual trigger valve then remove the dump valve (mn120-5) at the back of the head of gun. There should be two small allen screws then metal lid, then spring and oring. Pull out dump valve and make sure all the orings are in order. This valve should be able to move, not too tight. Use silicone paste lube on all orings (available at Lowes in plumbing department, Danco brand used for faucet orings). Reinstall dump valve and related parts and check for leaks. If air seems to be leaking from bottom of gun neer trigger, most likely problem is cycle valve (mm419-1) and related vinyl seat. These two parts are in the valve housing under the trigger. This valve also moves within its housing and seats on a vinyl oring. This part could be clear vinyl or black rubber. New seats are clear. Inspect these parts for scratches/cuts and lube with silicone paste. Hopefully you would have solved the problem with trigger valve. Good luck with your repair and do not dispare, this is one of the most difficult guns.

Jun 18, 2010 | Duo Fast Air Tools & Compressors

1 Answer

My 1/4 ratchet operates with air applied, without moving the pin. The pin and spring are there and free. This ratchet has sat in my tool box for 10+ years. Was there a plastic "ball" that used to be in...


Most CP ratchets have an oring that seals the trigger valve. You can remove the screw on the top of the trigger and then remove the spring and valve pin. There should be an oring around the bell of this pin. You can probably get away with using any oring that is the same size, and not having to get the exact oring from the manufacturer.

Aug 09, 2009 | Chicago Pneumatic 1/4" Air Ratchet

1 Answer

Need new reservoir


You can contact Briel direct they will supply spares but only from Portugal (I am in UK no one held spares) Email customer service Remember post costs could be high so consider replacing the Briel locally as it is obsolete and although a good entry level grinder, far better ones can be obtained and after all grind consistency is everything. If it is just the return spring see my FixYa. Address below Anabela Maia de SousaAfter Sales ServicesBriel - Industria de Electrodomesticos, S.A.Rua Sidonio Pais, 390 - Lugar do Rio4475-498 Nogueira da Maia - Portugalanabela@briel.ptwww.briel.ptTel: +351 22 961 9430Fax: +351 22 961 9435

Jul 27, 2009 | Briel CG5B Electric Burr Grinder

1 Answer

Change from natural gas to propane


1.You will need to change the pilot orifice and the burner orifices
2. You may need to change the gas control valve. Some gas control valves are made for natural gas and some are made for LP. They have regulators built-in, that deliver the correct pressure respectively. Natural gas is 3.5 inches of water column, LP is 10 inches of water column.
Some manufacturers sell kits to change the spring in the regulator from Nat to LP
You would need a parts breakdown on the specific model number of your fryer to find the parts you need. Hope this helps.

Apr 07, 2009 | Imperial IFS40 Deep Fryer

1 Answer

Briel Apollo no water when making espresso


Check that the water tank is seated properly. When you lower it in place just give it a little nudge down to make sure its slotted into the catch.

Nov 24, 2008 | Briel Domus Due Espresso Machine & Coffee...

1 Answer

Briel filter


You can get any Briel part you need at:
Electra-Craft
41 Woodbine St
Bergenfield NJ 07621
phone 201-439-1700
fax 201-439-1701
info@electra-craft.com
www.electra-craft.com

Jun 29, 2008 | Briel Chamonix ES-35 Espresso Machine

Not finding what you are looking for?
Briel Apollo ES-41BPG Espresso Machine Logo

Related Topics:

243 people viewed this question

Ask a Question

Usually answered in minutes!

Top Briel Coffee Makers & Espresso Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Henry  Thomas
Henry Thomas

Level 3 Expert

1074 Answers

yadayada
yadayada

Level 3 Expert

75822 Answers

Are you a Briel Coffee Maker and Espresso Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...