Question about Electric Chainsaw Sharpener

1 Answer

Chain saw oil

What oil do i use in a wen electric chain saw

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 4,088 Answers

Use regular bar/chain oil available from home centers, hardware stores, and saw dealers. Good luck!

Posted on Jun 12, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Chain for wen 14" chain saw cannot find. Other models fit? Thank you

My best advice is to find a lawn and garden shop that services chain saws. Take the chain you have and they can make one just like it.

Aug 30, 2013 | Remington Electric Chain Saw

2 Answers

16" Electric Chain Saw: what kind of oil is used for electric chain saw...

I assume you are asking about the oil for the chain. Any good quality "Bar and Chain Oil" will do fine. Do not use motor oil you use in your car engine as it will not properly lube the chain and will result in quicker dulling and early demise of the chain.

You can get the "Bar and Chain Oil" at most hardware stores or Farm Supply stores.

May 17, 2010 | Remington 16" Electric Chain Saw

2 Answers

How do I put chain back on the Wen 14'' chain saw

Remove the chain drive side plate and remove the bar. Clean the drive area and inspect the drive sprocket for excessive wear. Run the motor for a short time to make sure that oil is being pumped out to the bar--is should just ooze out. Clean the bar chain groove and clean the oil holes at the drive end of the bar--especially the two small holes that go from the large oil holes out to the chain groove. Back off the chain adjustment screw several turns, then fit the chain over the sprocket (teeth cut toward you on the bottom) and then insert the bar into the chain and push the bar out till the chain is fairly tight. Apply the side cover and make sure the adjustment tang drops into the large hole at the rear of the bar. Install the mounting nut(s) to hold the plate and bar together. When run-up finger tight, turn the adjustment screw CW until the chain becomes tight enough that it doesn't droop from the bar, yet can be be turned by hand. Tighten the side cover nut(s) and recheck tension. If ok, run the saw for a few moments with the bar tip near some cardboard--it should throw off a thin line of oil. Keep the chain properly sharpened to reduce the chance of this occurring again. Hope this helps!

Apr 29, 2010 | Garden

2 Answers

What lubricant oil is used on the blade of a Wen electric chain saw?

I have a Wen 2000 10" electric chainsaw and just ordered a new chain, , but does it need oil poured inside? I have no manual. what kind and how much? can it be over filled, there is a black screw off knob that appears to be for oil?????thanks Kim

Apr 02, 2010 | Electric Chainsaw Sharpener

2 Answers

Taking care of an electric chainsaw

Any motor oil will work to lubricate the chain.

Sep 16, 2009 | Poulan Pro 16-Inch 38 cc Anti-Vibration...

1 Answer

Where can I find a new chain bar adj screw for WEN 3818 gas saw?

Most older chainsaw adjustments are visible when the saw is viewed from the end of the bar back to the saw. More modern ones are near the bar nuts (side). Lou

Aug 26, 2009 | Electric Chainsaw Sharpener

1 Answer

Sae 20 motor oil?

not for crankcase means do not use it as an engine oil in lets say a lawnmower engine
yes it is ok to use only as bar and chain oil and if it is a automatic oiler be sure it is oiling.

Jun 10, 2009 | Heavy Machinery

4 Answers

Wen electric chain saw -is it doa?

Are you pressing the trigger lock with your thumb before you pull the trigger? That's a safety feature to prevent accidental sawing.

There's not a sensor for the oil, but you don't want to run the saw dry. It takes a special bar/chain oil which is thicker than motor oil.

FYI... if you look for a manual on the web, search for "Wagner chainsaw" because Wagner bought the chainsaw business from Wen.

Mar 10, 2009 | Electric Chainsaw Sharpener

Not finding what you are looking for?
Electric Chainsaw Sharpener Logo

Related Topics:

186 people viewed this question

Ask a Question

Usually answered in minutes!

Top Electric Garden Experts


Level 3 Expert

695 Answers

JohnPaul Robertson

Level 2 Expert

342 Answers


Level 3 Expert

666 Answers

Are you an Electric Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides