Question about Siemens 24 in. SE25T250 Free-Standing Dishwasher

1 Answer

The machine keeps sticking at 1 minute and then cant start another cycle because it wont finish !!!!

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Siemens Master
  • 2,605 Answers

Hello Catherine, welcome to Fixya. The reason your dishwasher is displaying a "1" is the control has detected a heating error. The error code is displayed by the number "1". Here`s the most likely reason why it has detected the error... The most likely and most common issue with your Bosch dishwasher likely lye`s within`the electronic timer/control, specifically the heater relay solder joint. ( a faulty flow switch, ntc or heater can also cause this, but not very probable ). This is why it runs forever unless pressing the two buttons for "cancel". To repair your unit It will require the removal of the control from the unit and then remove the control from it`s plastic housing and look for a burnt solder contact on the printed circuit board. This will be one of the pins from the heater relay, hence the unit sit`s at "1" ( because it can`t heat to advance or until canceled ) trying to heat the water. **Further to this, if you or someone you know is proficient at soldering, a lot of times it can be remedied by simply repairing the solder...although Bosch recommend`s replacing the control and I don`t pretend to speak on there behalf nor do I profess to know better. This is just my experience (it work`s) and my opinion (why buy new if one can repair ?)** **Please disconnect the power before attempting any service to the dishwasher. If you do not feel comfortable attempting this service, call a local pro, preferably one familiar with Bosch/Thermador/Gaggenau, to service your machine.** Hope this answer`s your question's, let me know if I can assist you further. Thank`s for visiting "fixya" for your repair inquiries. Please take a moment and rate this solution to it's helpfulness to you and leave a testimony if you're satisfied. Good luck. macmarkus :)

Posted on Jun 05, 2010

  • Mark MacDonald
    Mark MacDonald Jun 05, 2010

    Hello again Catherine,

    I neglected to mention that your dishwasher, Siemens is manufactured by B/S/H/ ( as is thermador, bosch, gaggenau & siemens ) which is Bosch. Sorry if that may have caused any mis-undersranding. All the same info applies to your dishwasher.

    macmarkus :)

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Lights keep flashing and door locks without finishing cycle


Kenmore HE2 Plus Front Load Washer Keeps unlocking ...

www.fixya.com > ... > HE2 > Kenmore HE2 Plus Front Load Washer
flashing prewash and add garment lights My HE2 Plus will fill with water, but when ...Kenmore HE3 2plus wont finish cycle Washer wont finish the last1 minute of cycle. ...We ran a load twice and it still did not unlock. du is the code for cannot ... Why does the door keep unlocking and locking in between the drum rotating?

Admiral, Whirlpool, Maytag - Washer Repair - Not ... - YouTube

? 5:51
https://www.youtube.com/watch?v=oBihToN6dxs
Sep 6, 2013 - Uploaded by ApplianceVideo.com
Troubleshoot your Admiral Top Load Washer that has these following symptoms: Not Completing all Cycles ...

Washing machines - Ariston



Jan 05, 2016 | Washing Machines

1 Answer

Bosch dishwasher gets stuck at 1 minute


New and highly targeted viral marketing campaigns can instantly place your product, service or brand in front of potential customers. See the best examples of viral marketing videos and social media strategies. Viral Marketing Company Plan Strategies and Resources Viral Shot

Mar 11, 2014 | Bosch 24 in. SGS43C12 Classixx...

1 Answer

Start matsui washing machine


Check the washer drain hose for clogs.

Jun 19, 2017 | Washing Machines

1 Answer

Washing machine has 1 minute left on cycle stuck door wont open programme not finished


Try the following, may work:
Press the Start/Cancel button together until all the console Led's illuminate
  1. Press both Start/Cancel and On/Off buttons together until 'd off' appears
  2. Default screen should return. Switch off.
  3. Wait for 2 minutes to try the door. If helped click.

Apr 18, 2013 | Hotpoint Ultima WF860 Front Load Washer

1 Answer

Kenmore HE3 2plus wont finish cycle


I'm not saying you don't have a problem. But just to be clear. You do understand that the last minutes on these machines can vary. The machine senses certain conditions in clothing, water discharge, etc. So sometimes the "1 min left" indication can stretch into many minutes. In theory, at least, it's possible your machine just needs to be left alone until it finishes whatever it's doing. However, one would think that any issues not resolved in 10 - 20 min are an indication of a problem. So i guess that's my next question, did you wait long enough? Keep in mind i am not a kenmore expert.

Jan 06, 2013 | Kenmore HE2 Plus Front Load Washer

1 Answer

Wont finish a small load. Gets to 4 minutes and


With a small load, the machine will have a difficult, if not impossible job of balancing the load. A bigger load will help. Another thing you can do is to use a low spin speed. If you wish to spin it out faster, just turn the machine back on after it has finished a cycle on the low spin speed and just push the spin speed button without selecting a cycle. You can touch the spin speed button until it shows the next higher spin speed, then push the start button and the machine will not fill with any water, it will just pump and spin. (about 14 minutes) This generally works, because you have spun most of the water out at a lower spin speed, and now the washer is able to reach the next higher spin speed as the load is not as unbalanced as it was before the low speed spin.

Nov 17, 2009 | LG WM0642H Front Load

2 Answers

WASHING MACHINE DOOR WONT OPEN


Call the manufacture it will be under warranty if it's only 6 months old as the machine will have to be torn down to get to the defective switch, just the top will have to come off if your lucky.

Jun 17, 2009 | Haier Washing Machines

1 Answer

C1 keeps popping up on display during cycle and wont finish. what do i do?


C1 isn't the code, it is a warning that a problem has been detected with the ABS system.

Apr 26, 2009 | Washing Machines

2 Answers

Washing machine


bottom right corner behind the little door

Sep 27, 2008 | Whirlpool AWM5125/1 Front Load Washer

1 Answer

It does not open


turn the machine off at the mains, after two minutes the door should release from the auto lock, but your pcb (printed circuit board) is knackered start saving.

Oct 15, 2007 | Indesit W 123 Front Load Washer

Not finding what you are looking for?
Siemens 24 in. SE25T250 Free-Standing Dishwasher Logo

1,036 people viewed this question

Ask a Question

Usually answered in minutes!

Top Siemens Dishwashers Experts

Paul Bade

Level 3 Expert

1536 Answers

shaun taylor

Level 3 Expert

1525 Answers

Mike

Level 3 Expert

4336 Answers

Are you a Siemens Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...