Question about Proview PL576Ws 15.4" Widescreen LCD Display

1 Answer

Black out the screen blacks out every couple of minutes...the green/yellow power button is still lit though.....in order to get the picture back, we have to turn the monitor off and then turn it back on.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 558 Answers

Blown capacitors on the inverter board inside it is fixable if you can solder

Posted on Apr 28, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

My flatron L1710S flat screen will not come out of power saving mode. When I turn on the monitor the power button/light is green for a few seconds, the screen indicated "power saving mode", then...


I switch on my PC, ensuring that all cables, leads and power supplies are connected properly. The tower powers up no problems at all. I switch the screen on, the green led lights up, the screen is completely black. A blue box appears centrally on the screen with the text 'power saving mode'. The green led light turns amber and then the screen just goes black.

Please don't suggest going to control panel, as I can't get that far.

PLEASE PLEASE CAN ANYONE SUGGEST ANYTHING give me

Mar 08, 2011 | LG Flatron L1710S 17" LCD Monitor

1 Answer

When i turn the monitor power button on monitor come on for about 3 seconds then screen goes black but power button is still lit. tryed old monitor and it works fine


Hello,

The picture board on your monitor is bad, since it goes black after three seconds, it means the picture board of your monitor has developed fault.

The best thing for you to do now is to take the monitor to a local repairer within your vicinity or any service center to help with the replacement of the picture board because the fault is not something you can fix yourself, in order not to complicate issues.

Take care.

Apr 22, 2010 | LG W2252TQ Monitor

1 Answer

M1991 screen stays black, little light is yellow


The fault is a back-light problem and the fault could be a faulty inverter board or a faulty CCFL lamp.
For service, parts and DIY info check out LCD Parts WEB site, please click on this link :-
www.lcdparts.net

Mar 15, 2010 | Dell Computer Monitors

1 Answer

Philips Brilliance 200w6cs Backlight off Green LED ONN


Check to see at one of the pin on the inverter board has 12vdc feeding it. No bad capacitors? Pictures?

Nov 29, 2009 | Philips Brilliance 200WP7ES - Flat panel...

2 Answers

The screen is black even though the green light is on


try with another cable, pc if nothing. need to get service.

May 30, 2009 | ViewSonic VA1912wb 19" LCD Monitor

1 Answer

Screen goes black,power light stays green. display only stays on a couple of seconds


This happened to me and I was able to fix it. I cracked it opened and found a bad capacitor, bought a replacement at Radio Shack and I'm back in business. Actually using it right now to post this.
-Jon

May 27, 2009 | ViewSonic Optiquest Q19wb LCD Monitor

1 Answer

My aopen f2925 monitor has a green tint.


The solution: hidden menu within the main menu itself. Hold the Menu button down while pressing Power to power on, and release power button only when the screen comes up, still holding the menu button. The menu will appear and there will now be a hidden selection, "Auto Color", printed in a red-on-black font at the bottom of the menu. Use the +/- buttons to access it, and press Menu. My green/yellow tint went away! Now my picture works great, and the setting lasts through Auto-Adjusts and Resets!

Apr 08, 2009 | AOpen F70PS 17" Flat Panel LCD Monitor

3 Answers

Lcd monitor power light flashing with no img. seems 2 be frozen


The display is in safe mode and you will need to reset the display to get the display out of the safe mode. There are 2 different model revisions. Please choose the method that will match your revision. Depending on the revision of the monitor, one of the following 2 methods should reset it to a normal state. This reset generally requires both hands and it is sometimes easier with another person.

If the serial number begins with an A and/or your power button on the far right (5th button from left):
Method #1
1. Unplug the VGA cable.
2. Remove the power cable from the back of the monitor.
3. Counting the buttons on the front of the panel from left to right as 1 – 5, hold the buttons 2 and 3 down at the same time (see picture above) and while continuing to hold the buttons, plug the power cable back in.
4. Keep holding the buttons for 5 seconds after the power has been plugged in and then let go. The green light should be steady when you release the buttons.
5. If the procedure worked, the green light will go to amber and you should see a "No Signal" message on the screen for a few seconds.
Method #2
1. Unplug the VGA cable.
2. Remove the power cable from the back of the monitor.
3. Counting the buttons on the front of the panel from left to right as 1 – 5, hold the buttons 2 and 3 down at the same time (see picture above) and while continuing to hold the buttons, plug the power cable back in.
4. Keep holding the buttons until the 4th green LED blink; then, let go. The green light should be steady when you release the buttons.
5. If the procedure worked, the green light will go to amber and you should see a "No Signal" message on the screen for a few seconds.


If the serial number begins with a B and/or your power button is in the middle (3rd button from left):
Method #1
1. Unplug the VGA cable.
2. Remove the power cable from the back of the monitor.
3. Counting the buttons on the front of the panel from left to right as 1 – 5, hold the buttons 2 and 4 down at the same time (see attached picture) and while continuing to hold the buttons, plug the power cable back in.4. Keep holding the buttons for 5 seconds after the power has been plugged in and then let go. The green light should be steady when you release the buttons.
5. If the procedure worked, the green light will go to amber and you should see a "No Signal" message on the screen for a few seconds.

Method #2
1. Unplug the VGA cable.
2. Remove the power cable from the back of the monitor.
3. Counting the buttons on the front of the panel from left to right as 1 – 5, hold the buttons 2 and 4 down at the same time (see picture above) and while continuing to hold the buttons, plug the power cable back in.
4. Keep holding the buttons until the 4th green LED blink; then, let go. The green light should be steady when you release the buttons.
5. If the procedure worked, the green light will go to amber and you should see a "No Signal" message on the screen for a few seconds.

If you have tried the reset a few times and it does not solve your issue, please Ask a Question to submit a request through the system or call 1-866-752-6271 Option 1 to contact technical support.

Mar 02, 2009 | Planar PL1910M (Black) 19 in. Flat Panel...

2 Answers

Sampo Flat Screen Black unless unplug and plug back in


i had the same problem now my monitor wont even turn on if i do that the power light just keeps blinking maybe its a sign of a dying monitor

Jan 16, 2009 | Sampo PD-70 15" Flat Panel LCD Monitor

1 Answer

Screen not appearing straight away


It could be your LCD backlight giving you problems till it warms up. Turn you computer on and while the monitor is displaying black and the power LED is green shine a flashlight in the lower left hand corner of your screen. Look for the ?Start? button, if your backlight is not working you?ll see a faint ?start? button if you look closely. A 15" LCD monitor is probably not an economically repairable problem unless you have access to really cheap parts and have the skills and tools to do the repair yourself.

Jul 29, 2007 | AOpen F55PS (Black, Silver) 15 in. Flat...

Not finding what you are looking for?
Proview PL576Ws 15.4" Widescreen LCD Display Logo

Related Topics:

106 people viewed this question

Ask a Question

Usually answered in minutes!

Top Proview Computer Monitors Experts

Diego Zenizo
Diego Zenizo

Level 1 Expert

22 Answers

Brad Brown

Level 3 Expert

13531 Answers

Terry Allen
Terry Allen

Level 3 Expert

680 Answers

Are you a Proview Computer Monitor Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...