Question about Pride Mobility Products New Pride Mobility Jet 3 Ultra Power Wheel Chair

2 Answers

I have a quantum power chair that has the light bar blinking it powers on and off but it does not move.please help

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 4,234 Answers

Check the safetly's. There are "safety switches" that will prevent the unit from moving without anyone actually sitting in the chair. This is so that while getting either in or out, the chair will not move, even if the controls are touched. It is possible that the connections to these may be open. By default, the switch is open. Sitting will close the switch allowing current to flow.

Dan

Posted on Jun 05, 2010

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 3,866 Answers

The issue on these is ether the motor has burned out on you or the battery is not getting enough current to turn the motor or you got a bad relay from the control panel to the motor, There is no way to diagnose this without having someone to come out to your home. But I can tell you this much my dad had one of these and his motor was the issue and when you got a motor issue in these mobility devices you might want to concider ordering a new chair if possiable. Just the parts and labor alone is over $1,500 trust me been there done that. So the best thing I can tell you is run test on the chair and if you cannot do that you need someone to visit your home to do that for you the cost to visit is like $125 bucks minium as they got to charge for there gas and there labor when they arrive. I would call the scooter store for a tech i nyour area.



Hope my information helps tho please do click the accept button for my efforts.

Posted on Jun 05, 2010

  • khaled_ali_1 Jun 05, 2010

    the motors are good the mane board and the control arm is new the battery is fully charged and it is good .

  • Grand Canyon Tech
    Grand Canyon Tech Jun 05, 2010

    I would say its the relay not allowign the motor to run, I just do not know how you call everything good or what you done to do your testing?



    If everything was good then the chair would be ok. There is something that is not getting the signal to the motor.



    let us know

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My quantum 600 wheel chair won't work it says system lock


My quantum 600 wheel chair won't work it says system lock ...

www.fixya.com/.../t26033304-quantum_600_wheel_chair_work_says_s...
2 hours ago - My quantum 600 wheel chair won't work it says system lock -Wheelchairs question.

Pride Mobility Quantum Q6 Edge (Power Wheelchairs ...

www.usatechguide.org/itemreview.php?itemid=1626
Quantum 6000 or 600 Rehab Power Wheelchair - CareCure Communitysci.rutgers.edu/.../showthread.php?...Quantum-6000...Rutgers UniversityJul 4, 2008 - 10 posts - ‎9 authorsI had the QUANTUM 600e Rehab Power Wheelchair for six months. ... C-500 Hvy dutypower chair w/hi-speed motors, power seating system, .... I have a Q600 with tilt, recline, leg extension, Q-logic..pretty much the works. ... the thing shuts itself off andwon't move when I have anything under 90% charge?Quantum® 600 Power Chair Reviews - Pride Mobilityownersclub.pridemobility.com/reviews/item/1/20The Quantum® 600 Power Chair delivers the stability of patented Mid-Wheel 6® ... At that same time the 3rd motor set was changed my seating system was ... We were rescued by boat and my friends say the wheelchair was working ... Insurance won'tcover a power chair for me yet so I had to pay out of pocket for this one.

Jan 01, 2016 | Health & Beauty

1 Answer

Push power button wont go but all the adjustments legs back tilt works


quantum 600 wheelchair troubleshooting Questions ... - Fixya

www.fixya.com > Forum > Tags
quantum 600 wheelchair troubleshooting chair won't go all i get form joystick is a picture of a ... around in a square there should be a rest button on the rear of the chair ,push ... Question about 600 E Electric Wheelchair - Used Power Chair.

[PDF]Pride Quantum 600 Owners's Manual - Scootaround

www.scootaround.com/.../Pride%20Quantum%20600%20Owner's%20M...
Quantum 600 .... The symbols below are used on the power chair to identify warnings, mandatory actions ... Pride will not be held responsible for injuries and/or property ...complete stop by releasing the joystick, then push the joystick forward slightly to .....breaker button, turn on the controller, and continue normal operation.

[PDF]Quantum 600E Owners Manual - Scootaround

www.scootaround.com/.../Pride%20Quantum%20600E%20Owner's%20...
Quantum 600E .... The symbols below are used on the power chair to identify warnings, mandatory ... chair. Pride will not be held responsible for injuries and/or property ... complete stop by releasing the joystick, then push the joystick forward slightly to ..... breaker button, turn on the controller, and continue normal operation.

[PDF]Quantum 600 Series - Pride Mobility Products


Dec 30, 2015 | Quantum 600 E Electric Wheelchair - Used...

2 Answers

My mother has a pride jet3 electric wheel chair that doesn't move now. the power button bar shows full charge and the light below that just blinks. Did she lock it up some how?


You can visit this website to find answers on what the flashing trouble indicator lights mean: http://www.pgdt.com/scenter/diagnostics/diagvsi.html
Locate the page that has the controller used on your power chair/scooter and count how many lights are flashing to diagnose the trouble. If your insurance purchased the power chair for you, they may also cover the repairs; contact them for information.
Good luck!

Dec 29, 2010 | Electric Jazzy 1115 Power Wheelchair

1 Answer

Lights on chair keep blinking and won't move


The number of lights that are blinking indicate what the problem is. Visit this site to locate the type on controller on your power chair and you will be able to see that the blinking lights mean:
http://www.pgdt.com/scenter/diagnostics/diagvsi.html
Try to reset your manual brake release as this is a common problem.
If you continue to have a problem, contact your manufacturer or dealer for service. If your insurance purchased they power chair for you, they may also cover the cost of repairs.
Good luck!

Sep 13, 2010 | Jet 7 Portable Power Chair

1 Answer

Lights keep blinking and chair won't move


The number of lights that are blinking indicate what the problem is. Visit this site to locate the type on controller on your power chair and you will be able to see that the blinking lights mean:
http://www.pgdt.com/scenter/diagnostics/diagvsi.html
Try to reset your manual brake release as this is a common problem.
If you continue to have a problem, contact your manufacturer or dealer for service. If your insurance purchased they power chair for you, they may also cover the cost of repairs.
Good luck!

Sep 13, 2010 | Jet 7 Portable Power Chair

1 Answer

Yellow lights blink and chair does not move on Jet 3 power chair


The number of lights that are blinking indicate what the problem is. Visit this site to locate the type on controller on your power chair and you will be able to see that the blinking lights mean:
http://www.pgdt.com/scenter/diagnostics/diagvsi.html
Try to reset your manual brake release as this is a common problem.
If you continue to have a problem, contact your manufacturer or dealer for service. If your insurance purchased they power chair for you, they may also cover the cost of repairs.
Good luck!

Jun 15, 2010 | Jet 3 Ultra Power Chair

1 Answer

All the lights are blinking very fast


try pushing the chair. If the chair moves your motors are disengaged. to engage your motors look at the base of the chair there should be a lever possibly 2 push, pull or turn depending and try your chair again if you need additional help you can reach me at 404-966-3734 and i can walk you through it

Jun 06, 2009 | Jet 3 Ultra Power Chair

2 Answers

My Jazzy select wheelchair does not run


you move the joystick and can hear something quicking in the motors

May 17, 2009 | Heavyduty Jazzy 1121 Standard & Heavy Duty...

Not finding what you are looking for?
Pride Mobility Products New Pride Mobility Jet 3 Ultra Power Wheel Chair Logo

339 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pride Mobility Products Health & Beauty Experts

wcdoc1953
wcdoc1953

Level 2 Expert

278 Answers

Colin Taylor

Level 2 Expert

346 Answers

Robin Hill
Robin Hill

Level 3 Expert

1263 Answers

Are you a Pride Mobility Products Health and Beauty Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...