Function buttons just get a "off" response instead of temperature

Perhaps indicating the oven door is locked.
Look for an unlock button.
my Fridgaire oven has a led to indicate door lock

you neglected to mention the model this is , but most of the ovens made by them , when switched to bake , 1st show the temp you adjust then after thrirty seconds or so show the actual temp of oven (this number will change) the set temp function can be adjusted to anything in the ovens heat range 100-450) using the arrow keys anytime in the bake cycle , just touching a arrow key will change display to set temp screen , from actual temp display

Good Morning Friend,

I understand you want to know how to turn on the oven on your Frigidaire range, model# FGF337GUD. First, make sure you have set the clock. You will do this by pressing the "Clock Set" button and then press and hold down the up or down arrows, until the correct time shows. After you have set the clock, you are ready to turn your oven on.

To set the temperature for your oven, you will press the "Bake" button and three dashes will appear. Press the up and down arrows to change the temperature. Note: The temperature will begin at a default temperature of 350 degrees. Once you have released the up or down arrow, your oven will begin heating to the selected temperature. When your oven reaches the desired temperature, it will beep once.

To cancel the baking function, you will press the "Clear/Off" button.

If you wish to change the temperature after baking has begun, you will press the bake button again, and then change the temperature by pressing the up or down arrows to either increase or decrease the temperature.

I ask that you please follow up with a comment on the post, at your convenience, to advise if further troubleshooting is needed or if your air conditioner status has changed successfully. Hope this is helpful.

-Best Regards-
WP

Hello,

To do that;

1. Press BAKE
   
   
2. Select a temperature of 550 or highest temp on some models its 500
   
   
3. Quickly (within 5-seconds of setting 550) press and hold the BAKE button approximately 5-15 seconds until "00" or the previously entered temperature adjustment is displayed.
   
   Pressing longer could cause an F0, F1 or F7 error to be displayed.
   
   
4. Press the UP/DOWN arrow button or turn the set knob to change the oven temperature in 5° increments to a maximum of +/- 35°
   
   
5. Press the CLEAR or OFF button to return to normal operation.

Gene

Hello,
Your oven will continue to indicate that it is preheat mode until the thermostat senses the proper set temperature. If you are getting no heat then you will need to address that issue. This could be many things but the most notorious would be the heating element. Could be the control panel as well. Some ovens have a knob for preheat, bake and clean with a separate knob to adjust the temperature. Make sure both are set properly.
Regards, Tony

Are you getting any codes? Sounds like one of your touchpad buttons is stuck. CAUTION: Turn power off to oven at circuit breaker.  I would take the control panel off disconnect the ribbon from the touchpad and take a pencil eraser and clean the contacts. Reconnect ribbon connector back together. If this does not help write back..

I need to bake in my oven how can I find the button to set the temp to bak?

The red key sign is a lock against children. To cancel it you have to hold the two buttons at the same time for 5 seconds (you activate it the same way).

The STOP sign appears after the cooker switches of after a power cut. You just have to press the left button, and, using the right knob, set the time.

See my response to http://www.fixya.com/support/t502356-whirlpool_accubake_oven_problem

It's the same issue. I think.

The E1- F5 error is a door lock error.

The control (TIMER) has likely failed in this instance - BUT...

Sometimes when you disconnect power to a range and reconnect it the electronic range control gets confused.
You should disconnect power again for 15 seconds and reconnect and see if that helps.

If it doesn't cure the E1- F5 error hold the bake button in until E0- F2 appears in the display.
This is the error for a stuck button on the keypad and is the way to clear the memory of the electronic range control.

Sometimes these work, but if the control has failed it won't make any difference.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.!!!!!