Question about HP Compaq dc5700 Microtower - Free Flat Panel until 113007 EW287AV-KIM PC Desktop

1 Answer

Turning off messages and savings pictures

I can't find my computer in your limited selection, so here is the computer information on my computer: it is a HP Pavilion Media Center M8100N TV PC, Product #GC673AA-ABA, S/N CXX20198P, Software Build # 73NAV3P4A1, Service # 112-007. Windows Vista, unfortunately, is my operating system. My Problems, so far, are two fold. One- I cannot get the messages disabled because my computer does not give me the option, after hitting PC Help and Tools, after HP Connections. Instead, I get a drop down of: Hardware diagnostic tools; HP Support Information; Recovery disc creation; and Recovery manager. Two- my other problem is that when I load pictures from my digital camera, a Canon Rebel EOS XTI, the pictures go to a program called "photo gallery" as well as to "My Pictures."
Once I am done with the pictures in "photo gallery," I can't delete them from there without deleting them from "My Pictures," also. The only way I can get the pictures to "My Pictures" is to go to the reclyce bin and restore each one individually. There are no instructions for retaining the pictures in "My Pictures, in the manual that came with the computer.

Barry E Mail: Vulture1972@tampabay.rr.com

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 749 Answers

First of all, a recovery disk would be helpful to make for future purposes. so if the backup program open, you might use it.

but if you get tired of the HP software opening--
1.click START-PROGRAMS-STARTUP--- delete any shortcuts here.
2.click start-run- type in "msconfig" when it opens , select the startup tab
uncheck all the boxes of programs you wish not to start when windows starts, click apply, then OK.
restart the computer. when it tells you "you have used the system configurator to change the way windows starts" check the box telling it not to tell you again and click OK.

this will NOT unistall any programs, just sets them to not open untill you manually open them which frees up system resources and make the computer run better.

Posted on Oct 08, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I can't upload photos from my mobile device


follow this steps and fix it. God bless you
· Connect your Cell phone to a computer using a USB cable. Drivers for the phone will be automatically installed when the phone is connected. A notification message should appear in the lower-right corner of your computer screen when the installation is completed.
· 2
Click "Start" and select "My Computer" from the menu. Double-click the Cell icon to open its folder on the computer.
· 3
Select and open a folder on your computer in which to save the picture.
· 4
Select a picture from your phone's open folder to transfer to your computer. Drag the picture to the folder where it is going to be saved. Continue to drag and drop pictures in the folder until the last picture is transferred.
· 5
Exit the phone's folder on the computer and disconnect the Cell phone from the computer.

Jul 31, 2013 | Facebook Social Network

1 Answer

Cant transfer pictures from my phone to the computer it says unable to charge


follow this steps and fix it. God bless you


Connect your Motorola phone to a computer using a USB cable. Drivers for the phone will be automatically installed when the phone is connected. A notification message should appear in the lower-right corner of your computer screen when the installation is completed.


  • 2 Click "Start" and select "My Computer" from the menu. Double-click the Samsung's icon to open its folder on the computer.




  • 3
    Select and open a folder on your computer in which to save the picture.

  • 4
    Select a picture from your phone's open folder to transfer to your computer. Drag the picture to the folder where it is going to be saved. Continue to drag and drop pictures in the folder until the last picture is transferred.

  • 5
    Exit the phone's folder on the computer and disconnect the Motorola phone from the computer.



  • Jul 30, 2013 | Motorola Mobility W375

    1 Answer

    I want to transfer my txt msgs from my phone memory of nokia n73 to sim


    Just select the the text messages and save ii into the saved message folder. But all the messages cannot be saved into your sim as it has limitation.

    May 23, 2011 | Nokia N73 Cellular Phone

    1 Answer

    How do I undo a reformat on an HP? My HP was reformatted and I need to return it to the previous state. Already tried system restore, but prompt said there is no point to restore to. Is there a way to...


    Troubleshooting
    Accessing Computer Setup
    The information and settings in Computer Setup are accessed
    from the File, Security, Tools, and Advanced menus.
    1. Open Computer Setup by turning on or restarting the
    computer. Press f10 while the F10 = Based Setup message is
    displayed in the lower-left corner of the screen.
    .
    To change the language, press f2.
    .
    To view navigation information, press f1.
    .
    To return to the Computer Setup menu, press esc.
    2. Select the File, Security, Tools, or Advanced menu.
    3. To exit Computer Setup, choose one of the following:
    .
    To exit without saving any changes, use the arrow keys to
    select File > Ignore changes and exit, and then follow
    the instructions on the screen.
    .
    To exit and save all the settings you have entered, use the
    arrow keys to select File > Save changes and exit, and
    then follow the instructions on the screen.
    Your preferences are set when you exit Computer Setup and take
    effect when the computer restarts.
    Computer Setup Defaults
    To return all settings in Computer Setup to the values that were
    set at the factory:
    1. Open Computer Setup by turning on or restarting the
    computer. Press f10 while the F10 = Based Setup message is
    displayed in the lower-left corner of the screen.
    .
    To change the language, press f2.
    .
    To view navigation information, press f1.
    2. Use the arrow keys to select File > Restore defaults.
    3. Select the Restore Defaults check box.
    2–2
    Maintenance and Service Guide

    Troubleshooting
    4. To confirm the restoration, press f10.
    5. Select File > Save changes and exit, and then follow the
    instructions on the screen.
    When the computer restarts, the factory settings are restored, and
    any identification information you have entered is saved.
    Selecting from the File Menu
    Table 2-1
    File Menu

    Select
    To Do This
    System Information ¦
    View identification information about the
    computer and any battery packs in the system.
    ¦
    View specification information about the
    processor, memory and cache size, video
    revision, keyboard controller version, and
    system ROM.
    Save to floppy Save system configuration settings to a diskette.
    Restore to floppy Restore system configuration settings from a
    diskette.
    Restore defaults Replace configuration settings in Computer Setup
    with factory default settings. (Identification
    information is retained.)
    Ignore changes and exit Cancel changes entered during the current
    session. Then exit and restart the computer.
    Save changes and exit Save changes entered during the current session.
    Then exit and restart the computer. The changes
    you save are in effect when the computer restarts.
    Maintenance and Service Guide
    2–3

    Troubleshooting
    Selecting from the Security Menu
    Table 2-2
    Security Menu
    Select To Do This
    Administrator password Enter, change, or delete an HP Administrator
    password.
    Power-on password Enter, change, or delete a power-on password.
    Password options ¦
    Enable/Disable stringent security.
    ¦
    Enable/Disable required password on restart.
    DriveLock passwords Enable/disable DriveLock; change a DriveLock
    user or master password.
    .
    DriveLock Settings are accessible only
    when you enter Computer Setup by turning
    on (not restarting) the computer.
    Smart Card Security Enable/disable power-on support for smart cards.
    .
    This feature is supported by select smart
    card readers only.
    Embedded Security ¦
    Enable/Disable the embedded security chip.
    ¦
    Restore embedded security chip to factory
    settings.
    ¦
    Enable/Disable power-on authentication
    support.
    ¦
    Enable/Disable automatic DriveLock.
    ¦
    Reset power-on authentication credential.
    .
    .
    Embedded Security settings are accessible
    only if the computer is equipped with an
    embedded security chip.
    Device security Enable/Disable devices in the system.
    Enable NIC for inclusion in MultiBoot.
    System IDs Enter user-defined identification values.
    2–4 Maintenance and Service Guide

    Troubleshooting
    Selecting from the Tools Menu
    Table 2-3
    Tools Menu
    Select To Do This
    HDD Self Test options Run a quick or comprehensive self-test on any
    hard drive in the system.
    Battery Information View information about any battery packs in the
    computer.

    Jan 01, 2010 | HP Pavilion dv4000 Notebook

    1 Answer

    Saving pictures to PC from memory card


    Please follow these instructions to save photos to your computer: (You may also download a copy of the manual for your printer from this site.)
    Saving Photos to Your Computer
    1. From the I Want To... menu on the display, scroll to Save to Computer, and then press the Select button on the operator panel.

    2. Press the left or right arrow on the navigation button to scroll through the photos on the media card or in the digital camera.

    3. Press the Select button to select a photo to save to your computer. You can select more than one photo at once.

    4. Press the Save to PC button on the operator panel. The Memory Card Manager automatically launches on your computer.

    5. In the Memory Card Manager, verify that the photos you want to save are selected, and then click Next.

    6. Browse to the folder in which you want to save your photos and make any changes to the Save/Launch Options, and then click Next.

    The photos are saved to your computer.

    I hope this information allows you to resolve this issue. If you need further assistance, please post back with a comment to this thread.
    If I've managed to answer your question or solve a problem, please take just a moment to rate this post....thanks!

    Jun 23, 2009 | Dell 942 All-In-One InkJet Printer

    2 Answers

    Saving text messages from v365


    You can save the text messages into the computer using the software from Motorola.
    Motorola Phone Tools allow you to transfer all the information between the cellphone and the computer.
    You can get it from store.motorola.com
    Also remmber that you are not gonna be able to save text messages or contacts information in a memory card.
    The memory card allow you to transfer just Multimedia stuff as music pictures or videos.
    Good luck

    Oct 24, 2008 | Motorola Mobility V365 Cellular Phone

    2 Answers

    When i try to ytyake a picture an error message appears memory card error


    Is that exact what it says? I need more information. What kind of camera is it? I'll try to help with the little information I have:

    I think your memory card is full and needs to be formatted. Select 'Menu' and look for the 'Format' option and select it. Before you select 'Yes' make sure you save any pictures that you might want to keep onto your computer. Because once the memory card is formatted you won't be able retrieve the pictures. It should ask you before formatting your memory card. While it's formatting make sure to keep the camera steady (if it's an older camera the slightest bump could disrupt the formatting process). This should take no more that a minute or two. When it's complete your memory card will be completely wiped clean. You'll now be able to take pictures. If the message appears again repeat the same process.

    Note: When you 'Delete' a picture it doesn't completely leave your memory card. It will continue to take up space until you format your card.

    I suggest formatting your memory card often (or you might miss out on a perfect photo opportunity and have to delete pictures you haven't put on your computer yet).

    I hope this helped,

    Owen

    Sep 22, 2008 | Cameras

    4 Answers

    My LG enV phone problem


    Wow. Some of you are retards, sorry, but you don't know how this phone works.
    A) Auto-Save if for SENT messages only. If it is on, it will save your sent message in the sent box. if set to off, then it will not show any sent messages. If set to prompt, then it will ask you after the message is successfully sent from your phone to the Verizon network.
    B) Auto-erase is for INBOX only. It will automatically erase the last message in your inbox when it reaches it's max capacity.
    C) The LG EnV can accept up to 4GB of memory. (hollowtech2, you are the ****** i mentioned above, don't pur information you have not confirmed. people will dissprove you, and you will be embarrassed.)
    D) i am still looking to solve the text messgae save limit problem. i will post it when i find out.

    Jan 21, 2008 | LG enV VX9900 Cellular Phone

    1 Answer

    "The device is not ready"


    This error message means that the preferences in EasyShare software are set to save pictures to the CD-ROM drive or some drive other than your hard drive. To correct this, follow these steps: Start EasyShare software. Select Tools > Preferences. Select the Transfer tab. Below "Select the location on your hard disk where you want to copy transferred pictures," select Browse. Browse to the desired location on the hard drive where you want to transfer your pictures. The default location is: For Windows 98/Me Operating Systems: c:/My Documents/My Pictures/Kodak Pictures For Windows 2000/XP Operating Systems: c:/Documents and Settings/user name/My Documents/My Pictures/Kodak Pictures Select OK to return to Preferences, then click Apply and OK to save and close the Preferences. Reconnect the camera, and transfer the pictures.

    Aug 29, 2005 | Kodak EasyShare CX7530 Digital Camera

    2 Answers

    Transferring pictures from my Kodak EasyShare digital camera to my computer


    This error message means that the preferences in EasyShare software are set to save pictures to the CD-ROM drive or some drive other than your hard drive. To correct this, follow these steps: Start EasyShare software. Select Tools > Preferences. Select the Transfer tab. Below "Select the location on your hard disk where you want to copy transferred pictures," select Browse. Browse to the desired location on the hard drive where you want to transfer your pictures. The default location is: For Windows 98/Me Operating Systems: c:/My Documents/My Pictures/Kodak Pictures For Windows 2000/XP Operating Systems: c:/Documents and Settings/user name/My Documents/My Pictures/Kodak Pictures Select OK to return to Preferences, then click Apply and OK to save and close the Preferences. Reconnect the camera, and transfer the pictures.

    Aug 29, 2005 | Kodak EasyShare One Digital Camera

    Not finding what you are looking for?
    HP Compaq dc5700 Microtower - Free Flat Panel until 113007 EW287AV-KIM PC Desktop Logo

    85 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top HP Computers & Internet Experts

    Brian Sullivan
    Brian Sullivan

    Level 3 Expert

    27725 Answers

    Les Dickinson
    Les Dickinson

    Level 3 Expert

    18381 Answers

    Tony

    Level 3 Expert

    2599 Answers

    Are you a HP Computer and Internet Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...