Question about Heating & Cooling

Open Question

Does anyone know where I can find a schematic for a ruud horizontal furnace. Model No. UGUF-075A-ER

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 182 Answers

SOURCE: Ruud Furnace Door

measure it and have any sheetmetal shop make ya one up.much cheaper than a new furnace

Posted on Nov 03, 2008

Ad
machtcl1
  • 61 Answers

SOURCE: Ruud Furnace needs replacement

What part of the country?
How many square feet in the house?
Insulation?
Single pane glass?
Many factors should be considered by a professional.
However if the old unit worked OK, a new 80% 70,000 unit will most likeley replace a 24 year old 60-70% 75,000 unit.

Posted on Dec 16, 2008

  • 1033 Answers

SOURCE: My RUUD furnace, model ugld-06nc-er

If the blower motor runs continousley and the thermostat is not set to fan then the intergrated control board is malfunctioning and must be replaced. Usually because the relay that energized the motor is bad. If you are refering to the inducer motor running all the time then the pressure switch is open and must checked for a restriction in the flue pipe or blockage in the vent.

Posted on Jan 17, 2011

Testimonial: "Thank you so much, very helpful"

TheMobilian
  • 8220 Answers

SOURCE: I need the wiring schematic

Rich tips for hvac knowledge seekers

Whats going on with the unit. Can't nobody find schematics online for HVAC.

If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

Posted on Mar 28, 2011

  • 127 Answers

SOURCE: what is the efficiency rating of a ruud ugra

80 percent furnace

Posted on Oct 21, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a Ruud Achiever 90 Plus Gas Furnace with Air Conditioner. I have a new Nest Thermostat. What is the correct wiring connections on the Furnace?


A Ruud Achiever gas furnace I believe came in a two stage model for heating. What this means is that you will have a high and a low setting. Your furnace should have two wires that control the heating cycle a W1 and W2. This should correspond with the terminals on the nest thermostat. You may run into issues if you do not have enough thermostat wires to control the furnace. If you are ever in the need for Ruud And Rheem Gas Furnaces we offer a great selection online. Shop Natural Gas Furnace. We also have a chat line which can provide technical support.

Dec 26, 2017 | Ruud Heating & Cooling

2 Answers

Are the filters for my Ruud 80 plus furnace supposed to be installed vertically or horizontally?


Hello Donna Haslam

What ever EFECTIVELY BLOCKS all air
BEFORE it enters your heater...

Check out your air intake...

If this is the DESIGN EXERCISE it feels like...
Consider buying an INTAKE HOUSING
that takes a STANARD SIZE air filter.

FILTER...
AT THE INTAKE is a superior location
because it prevent dust & "stuff" from
EVER ENTERING your DUCT work.

Carnac
Carnac the Magnificent

Mar 19, 2017 | Ruud Heating & Cooling

1 Answer

Ruud furnace Model# UGDA-075A-CR. I would like to repair the heat Exchanger Group. Are parts available to purchase?


Im sure they are but if not done by a qualified technician you could come across some very difficult paths

Jan 05, 2017 | Ruud Heating & Cooling

1 Answer

Ugda-075a-cr this the correct model number for ruud furnance i have


Now how would anyone here know if that is the correct number .contact Rudd and ask them

Dec 02, 2015 | Ruud Heating & Cooling

1 Answer

I need a manual for a 1985 ruud furnace model # ugla-100c-er


Good luck. The most common failure in those is the gas valve and draft motor.

Mar 01, 2015 | Ruud Heating & Cooling

1 Answer

What is the blink code for Ruud 2 stage ac/furnace


on the board itself or on the schematic there is a legend that will tell you what the blinks mean. start there. its just a diagram that gives you the fault according to the number of blinks

Sep 29, 2012 | Ruud Heating & Cooling

1 Answer

Ruud Furnace needs replacement


What part of the country?
How many square feet in the house?
Insulation?
Single pane glass?
Many factors should be considered by a professional.
However if the old unit worked OK, a new 80% 70,000 unit will most likeley replace a 24 year old 60-70% 75,000 unit.

Dec 14, 2008 | Carrier 38CKC042 Air Conditioner

Not finding what you are looking for?
Heating & Cooling Logo

Related Topics:

89 people viewed this question

Ask a Question

Usually answered in minutes!

Top Heating & Cooling Experts

Paul Carew

Level 3 Expert

3309 Answers

Tim Whalen

Level 3 Expert

3074 Answers

yadayada
yadayada

Level 3 Expert

80339 Answers

Are you a Heating and Cooling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...