Question about Kenmore 22422 Top Load Washer

1 Answer

Help! thanks for helping me with my washer. unfortunately i could not get the back panel off. is there any way we can discuss this over the phone ? because i really have no idea what to do and i dont want to pay $179  for sears to come fix it if i can jus do it myself.  thanks again

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 184 Answers

TOP LOAD KENMORE WASHERS ARE NOT ACCESSED FROM THE BACK.
1. FIND TWO SCREWS IN THE CORNER OF THE CONSOLE.
THEY MAY BE VISIBLE FROM THE FRONT OR THE BACK.
THEY ARE DOWN LOW TO SECURE THE CONSOLE TO THE CABINET. THEY MAY ALSO BE BEHIND THE TRIM ON EACH SIDE OF THE CONSOLE ON SOME MODELS
2. ONCE THE SCREWS ARE REMOVED, THE CONSOLE WILL FLIP UP AND BACK OUT OF THE WAY. IT IS HINGED ON THE BACK. DISCONNECT THE LID SWITCH CONNECTOR.
3. REMOVE TWO CLIPS HOLDING THE CABINET TO THE BACK PANEL. PLACE A SCREWDRIVER IN THE FRONT HOLE OF THE CABINET THAT THE CLIPS GO INTO. PRY UP AND BACK ON THE CLIP TO RELEASE IT.
4. TIP THE CABINET TOWARD YOU AND LIFT OFF OF THE BASE. EVERYTHING IS ACCESSIBLE TO YOU AT THIS POINT.

Posted on Apr 15, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

How to remove back of washer


Hello, Thank You for using FixYa. I will be helping you today.If its a front loader just remove all the 1/4 inch screws from the back cover. If its a top load remove the control panel back corner screws flip up control remove two clips unplug lid switch and remove the whole cabinet.The back does not come off the top load whirlpool.
Thank You and please rate my answer if it was helpful..

Jun 11, 2011 | Whirlpool Washing Machines

1 Answer

Is there an easier way to access the water pump than turning the machine upside down? we havn't found any of the panels that are easily removed. thank you. rvclay


Hi,

No, unfortunately that is pretty much how you get to it. If you can tilt the unit back about 45 degrees and block it up so it wont tip on you, its not too bad to get at while laying on the floor. just try to get it back far enough that the remaining water is below the pump.

Hope that helps
good luck

May 11, 2011 | Fisher and Paykel GWL11 Top Load Washer

1 Answer

Fav6800aww machine wont stay balanced move the clothes around it starts back up for about one minute then stops code comes up dc thanks earl


Google this; Neptune TL Washer FAV6800AWW

This is a DIY Appliance repair forum and you can get the Service Manual and repair support at that site..

In the Sticky: Neptune TL Washer FAV6800AWW 5 post down you will find a link to the Service Manual. You absolutely need the Service Manual to DIY issues with the machine. It's not the best SM but will get you started. I also have repair post in that sticky to help with the most common issues that I have helped owners with. I'm an owner of a FAV6800AWW top load machine.

In that Sticky I discuss what is the cause of DC or UC unbalance errors and the fix.

Apr 14, 2011 | Maytag Neptune FAV6800AW Top Load Washer

2 Answers

My Kenmore Elite drum will not turn for the wash cycle or the spin cycle and now my door is locked and pressing the cancle button dosnt work or unplugging the washer


Hi

Most probably you'll need to replace the door latch assembly however before doing that you can leave the washer unplugged for 30minutes so that it resets itself. In the meantime when it's unplugged just inspect the door latch wiring to ensure all the connector plugs are intact and not loose or broken. You can access the door latch wiring harness by removing the top panel of the washer. To remove the top panel just removes the three screws that hold the panel in place in the rear of the washer. With the screws removed, the panel will slide back, and then lift off.Also after removing the top panel push all the connectors, as they might become loose. However locate the door latch assembly behind the front panel on the right hand side. Trace all the connectors from the door latch to the Central Control Unit (CCU) and make sure they are properly seated at both ends. If after doing this still the issue is not resolved then unfortunately you have to get the door latch replaced.

Please get back to us if you have further query else please accept the suggestion.

Thank you for contacting fixya.com

Jan 07, 2011 | Washing Machines

1 Answer

Machine won't do anything and showing error 23


Sorry to read about your problem, I hope this helps you out.

An E23 error code on your Frigidaire washer indicates a failure of the drain pump relay.


Depending upon the model, your washer may be under warranty for up to 25 years, so check your warranty's status before attempting any repairs yourself.

    Try to Clear the Code
  1. A power outage can cause error codes to display on the screen, even if there's no problem. Hold down the "Cancel" button for three seconds, or unplug the machine briefly to see if the code goes away. If it returns, the problem is real.
  2. Check the Pump
  3. Unplug the machine and remove the service panel. Locate the pump on the floor of the machine, to the left of the tub, towards the front. Inspect the wiring for burns, breaks or loose connections, and replace as necessary. Use only appliance-grade wire.
  4. Replace the Control Panel
  5. If the wiring is fine, the problem is a severed relay on the control panel. Unfortunately, this cannot be repaired and must be replaced. Remove the control panel from the upper portion of the back of the machine, and replace with an identical part from Frigidaire.

I tried to help you. Please help me and Rate/Vote on my response. We take the time to answer your question. take the time to rate us.Thanks and good luck

4 Thumbs - Very Helpful
3 Thumbs - Helpful

Dec 30, 2010 | Frigidaire ATF6000ES Front Load Washer

1 Answer

Hi there, I have a Kenmore Elite H3t and wanted to do a load of laundry today and it keeps blinking in Red DL and then F. I looked through my manual in the troubleshooting area and of course that...


Hi

Thanks for using FixYa. Error "dlf" means a door latch failure. This means that you'll need to replace the door latch assembly however before doing that you can leave the washer unplugged for 30minutes so that it resets itself. In the meantime when it's unplugged just inspect the door latch wiring to ensure all the connector plugs are intact and not loose or broken. You can access the door latch wiring harness by removing the top panel of the washer. To remove the top panel just remove the three screws that hold the panel in place in the rear of the washer. With the screws removed, the panel will slide back, and then lift off. Locate the door latch assembly behind the front panel on the right hand side. Trace all the connectors from the door latch to the Central Control Unit (CCU) and make sure they are properly seated at both ends. If after doing this still the issue is not resolved then unfortunately you have to get the door latch replaced. Please rate the solution if the issue is resolved or else revert for further assistance.

Thanks
Rylee

Oct 08, 2010 | Kenmore Elite 45986 Front Load Washer

1 Answer

Thanks I thought it might be the inlet valve, but to get access to it behind the top panel, Is there a trick to removing the panel? I have removed the three screws behind the detergent drawer but the panel...


Hi, you will need to unstack the dryer unfortunately, then remove the three screws at the back of the top washer panel and it will slide back about 2 or 3cm and up away from the unit. Then you will see how to remove the valve. Hope that answers your question. Thanks for visiting "fixya". Let me know if you require any further assistance and good luck. Macmarkus :)

Jun 17, 2010 | Asko W6021 Front Load Washer

1 Answer

Dl F signal on kenmore elite front loading washer


Hi



Thanks for using FixYa. Error “dlf” means a door latch failure. This means that you’ll need to replace the door latch assembly however before doing that you can leave the washer unplugged for 30minutes so that it resets itself. In the meantime when it’s unplugged just inspect the door latch wiring to ensure all the connector plugs are intact and not loose or broken. You can access the door latch wiring harness by removing the top panel of the washer. To remove the top panel just remove the three screws that hold the panel in place in the rear of the washer. With the screws removed, the panel will slide back, and then lift off. Locate the door latch assembly behind the front panel on the right hand side. Trace all the connectors from the door latch to the Central Control Unit (CCU) and make sure they are properly seated at both ends. If after doing this still the issue is not resolved then unfortunately you have to get the door latch replaced. Please do rate the solution if the issue is resolved or else revert for further assistance.



Thanks
Rylee

Jun 14, 2010 | Kenmore Elite 45986 Front Load Washer

8 Answers

Kenmore Elite Frontload washer


Dea, F02 is the code for long drain. Your filter on your pump is probably clogged with lint and stuff. You have to remove the bottom front panel, 3 screws. The panel will drop and come off. The filter cover is right in front. Get yourself a bunch of towels and unscrew the filter cover and twist the filter out. Clean out all the stuff and put it back in. See if the washer comes back to life...Catriver..post back

Apr 28, 2007 | Kenmore Elite 45986 Front Load Washer

Not finding what you are looking for?
Kenmore 22422 Top Load Washer Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Washing Machines Experts

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Archaeology
Archaeology

Level 3 Expert

662 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Kenmore Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...