Question about Troy-Bilt Pony Garden Tiller
I have a troy bilt tiller 5 hp briggs engine need manuals.
would like to know how low speed and high works
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
SOURCE: tilller will not run
Get the model # and serial # off of the sticker. Got to the Troy Bilt site and use the owners manual link. Need to leave off the last 3 numbers of the model #.
If that site does not have the manual, I've found them on the MTD site. I enter only the first 2 numbers of the model # and then hunt for my manual from the list.
If all else fails, you can call Troy Bilt at their # provided on the site.
Hope this helps.
Posted on May 20, 2009
SOURCE: troy bilt jr tiller
If you try to till too deep, this is what will happen. You have to start shallow and and gradually lower the depth on subsequent passes. That will even happen on my 'Horse' model if I try to go too deep too fast.
Posted on May 25, 2009
From what I read you need a new rewind clutch and the spring and cord go into the housing. Briggs is easy to fix. contact me at email@example.com and I can send you what you need or you can send it to me and I will repair it very cheap!! Parts are available at almost any small engine parts place.
Posted on Jul 18, 2009
It's definitely do-it-yourself in that no special tools or skills are required, but it can be a little tricky. You can see that the the recoil starter is in an assembly which is spot welded onto a metal cover. You have to remove the entire metal cover that includes the recoil starter. There may be 6 to 10 screws to remove to do that. When you get it off you will see a plastic spool that holds the cord. This spool is probably held in place by a couple of metal tabs that are bent down. Bend those tabs up with pliers. Underneath the spool is a spiral spring that provides the recoil. Take careful note of how this all goes together. Buy a new cord (available by the foot at a hardware store) and wrap it around the plastic spool. Use a piece of tape to hold the end of the new cord above the spool so you can thread it through the hole in the metal housing later. Put the spring and the spool in place, then wind the spool to put tension on the spring - about 5 turns in the direction that would push the string out through the hole. Once you have the spring "wound up" remove the tape and thread the end of the cord through the hole. Now bend those metal tabs back down. Put the handle on the cord end (or tie a knot) to keep the spring from pulling the end of the cord back through the hole. Reassemble the rest and you are in business.
Posted on Jun 15, 2010
Tips for a great answer:
Oct 20, 2010 | Troy-Bilt Chipper Shredder
Jun 27, 2010 | Troy-Bilt Garden
May 13, 2010 | Troy-Bilt Pony Garden Tiller
Apr 10, 2010 | Troy-Bilt Pony Garden Tiller
May 19, 2009 | Garden
Apr 29, 2009 | Troy-Bilt Pony Garden Tiller
Apr 25, 2009 | Troy Bilt, Tuffy, Rear - Tine Tiller, 4.0...
Mar 21, 2009 | Troy Bilt, Tuffy, Rear - Tine Tiller, 4.0...
Feb 21, 2009 | Troy Bilt, Tuffy, Rear - Tine Tiller, 4.0...
Jul 01, 2014 | Troy-Bilt Pony Garden Tiller
43 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: