Question about HP TouchSmart IQ770 PC Desktop

3 Answers

HP IQ770, won't boot, only displays HP Logo screen

HP IQ770, on startup the screen displays the HP logo, and the Boot Menu, Setup, and Recovery options. Keyboard locks up with the Num Lock when any key is pressed. Touch screen beeps when contact is made.

Symptoms remain with a 2nd known good keyboard as well as after clearing the CMOS.

Posted by on

Ad

3 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 13 Answers

Hi, this is the best solution ever- i was surfing all the possible forums- found THE SOLUTION for my HP TouchSmart IQ770 not booting up, freezing on hp logo with blue screen and non functional keyboard.... the problem is in... you wouldn't believe this- card reader!!! disconnect cable from reader board, NOT from motherboard side and power up! Here is link for detailed explanation- scroll down to johnnyzero comment - HE IS THE REAL HERO!!! http://www.tomshardware.com/forum/256184-28-pavillion-start-bios-info-start

Posted on Feb 08, 2012

  • CrazeeRay
    CrazeeRay Feb 08, 2012

    Read this - scroll down to johnnyzero comment on http://www.tomshardware.com/forum/256184...

×

Ad
  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 15 Answers

You need to run a BOOT CD Here is a link for a great Boot CD Diagnostic Software that you can make. If You are not able to9 use your PC Just have one of your friends make this Boot CD for you then look at whats really going on with your system. Here is the link for the CD Home Page:
http://www.hiren.info/pages/bootcd

Posted on Jun 03, 2010

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Guru:

    An expert who has written 7 tips or uploaded 3 video tips

  • Expert
  • 285 Answers

Upgrade ur bios

Posted on Jun 03, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Dont startup


1 Turn on the computer.
2 As the computer starts, press <F8> on the keyboard until the Advanced Boot Options menu appears on the screen.
new_note.jpg Note: You must press <F8> before the Windows logo appears on the screen. If you press <F8> after the Windows logo appears on the screen, the Advanced Boot Options menu will not appear on the screen. If you do not see the Advanced Boot Options menu, restart the computer, and then repeat this step until you see the menu on the screen.

Dec 14, 2013 | Dell Inspiron 1501 Notebook

1 Answer

How do i get to recovery mode for ubuntu?


  1. Switch on your computer.
  2. Wait until the BIOS has finished loading, or has almost finished. (During this time you will probably see a logo of your computer manufacturer.)
  3. Quickly press and hold the Shift key, which will bring up the GNU GRUB menu. (If you see the Ubuntu logo, you've missed the point where you can enter the GRUB menu.)
  4. Select the line which starts with "Advanced options".
  5. Select the line ending with "(recovery mode)", probably the second line, something like: Ubuntu GNU/Linux, with Linux 3.8.0-26-generic (recovery mode)
  6. Press Return and your machine will begin the boot process.
  7. After a few moments, your workstation should display a menu with a number of options. One of the options (you may need to scroll down to the bottom of the list) will be "Drop to root shell prompt". Press Return with this option highlighted.
  8. The root partition is mounted read-only. To mount it read/write, enter the command
    mount -o remount,rw /
  9. If you have /home, /boot, /tmp, or any other mount point on a separate partition, you can mount them with the command
    mount --all (This must be done following step 8 so that /etc/mtab is writable.) Alternatively, you could try selecting "Enable networking" in step 7, though this has been found to cause the system to hang (see https://bugs.launchpad.net/ubuntu/+source/friendly-recovery/+bug/981792).
NOTE 1: If you have Ubuntu Quantal (12.10) or earlier, omit step 4 (the recovery mode menu items are displayed on the top-level menu).
NOTE 2: If you reboot, there is no need to hold the Shift key in step 3. The GNU GRUB menu will continue to be displayed automatically on each boot until a normal startup of Ubuntu completes. To configure GRUB so the menu is always displayed, even after a normal startup, see https://help.ubuntu.com/community/Grub2/Setup.

Oct 16, 2013 | Compaq Computers & Internet

1 Answer

Compaq Presario pops up a system boot menu everytime at startup.


This comes up mostly when it requires a BIOS save. Try that. If that does not help, sometimes setting the default settings and saving will help.

Dec 04, 2012 | Computers & Internet

1 Answer

I need to press a key on my keyboard to start factory recovery


Hi and welcome to Fixya!

In order to revert the machine back to its factory setting, you need to have the recovery disk (if you don't have it, call the warranty support line of e-machines so they can provide it to you).

To restore Windows from your recovery discs, you will need to
insert the first backup disc and enable the F12 Boot Menu via the BIOS Setup
Utility.
1 Turn on your computer and insert the first system recovery disc into the
optical disc drive. Restart your computer.
2 During startup when the eMachines logo shows, press the F2 key to enter
BIOS Setup, where you can set system parameters.
3 Use the left and right arrow keys to select the Main submenu.
4 Use the up and down arrow keys to select F12 Boot Menu.
5 Use the F5 or F6 key to change F12 Boot Menu to Enabled.
6 Press the ESC key to enter the Exit submenu, press the ENTER key to Exit
Saving Changes. Press the ENTER key again to select Yes. The system will
reboot.
7 After rebooting, when the eMachines logo shows, press the F12 key to
open the Boot Menu. Here you can select which device to boot from.
8 Use the arrow keys to select the IDE1*, then press the ENTER key. Windows
will be installed from the recovery disc.
9 Insert the second recovery disc when prompted, then follow the onscreen
prompts to complete the restore.
10 Remove the recovery disc from the optical drive once the restore is
complete. Do this before rebooting your computer.

Hope this helps!

Takasashi

Jul 25, 2011 | eMachines E620-5885 Notebook

1 Answer

Pavilion does not boot. Lights on strip below screen flash on and off. HDD drive does not come on


-If you are not able to boot in Windows but still able to get error codes like from windows you can just reinstall the Operating system using your recovery discs
-If there's no display at all even the HP logo upon startup its a motherboard issue
- if you are able to get the hp logo in startup but not able to go to windows its a RAM issue

Dec 29, 2010 | HP Computers & Internet

1 Answer

HP Pavilion ze2308wm won't boot up


Have you tried an external keyboard, either PS2 or USB depending on what ports are available?

Mar 14, 2010 | HP Pavilion ze2000 Notebook

1 Answer

Will not boot up. Screen displays Window XP


Use your original Windows XP CD and run the recovery console when starting up the pc. Thats should repair any files which are hanging the pc at the XP logo

Oct 13, 2009 | HP vs17

1 Answer

Windows not loading


Sounds like you have a nasty virus that has corrupted your harddrive

so that means that the recovery portion is corrupted as well

you need the operating system and reinstall everything

Mar 12, 2009 | HP PAVILION M1072N MEDIA CENTER - P4 530...

1 Answer

Reformatting my computer


  • Using System Recovery CDs
  • Change the boot order in the BIOS:-
  • Turn off the computer:
  • Disconnect devices that are connected to USB, Fire wire, parallel and serial ports, except the keyboard, the mouse anb Internet Connection.
  • Turn on the computer.
  • When the color screen with the logo appears, press the F1 key on the keyboard until Entering SETUP is displayed. (You only have a few seconds to press the F1 key before the normal startup process continues.)
  • Wait until the BIOS setup program opens.
  • Press the right arrow key to select Boot.
  • Press the down arrow key to select Boot Device Priority, and then press Enter on the keyboard.
  • Change the first boot device to CD-ROM using one of these methods:
  • Press the down arrow key to select the CD-ROM item. Press the + (plus) key to move the CD-ROM item up until it is the first item in the list.
  • Press the down arrow key to highlight the First Boot Device selection. Press the + (plus) key until CD-ROM is the selection.
  • Start the recovery:-
  • Press the Eject button on the top CD-ROM drive, and wait for the tray to open. Insert the System Recovery CD #1 and close the tray.
  • Press the F10 key to save the changes and exit BIOS.
  • With Yes selected, press Enter.
  • The recovery window automatically starts; wait for the onscreen instructions to display, and then follow the instructions:-
  • Press R, and then press the F key again.
  • Click yes to perform the full system recovery.
  • Insert the remaining CDs when directed.
  • When the recovery program finishes, click Restart to restart the computer.
  • Before the computer restarts, the CD tray ejects. Remove the CD
  • Return the BIOS to the previous setting
  • When the color screen with the logo appears, press the F1 key on the keyboard until Entering SETUP is displayed. (You only have a few seconds to press the F1 key before the normal startup process continues.) Wait until the BIOS setup program opens.
  • Press F5 Key to Set Default Settings in BIOS.
  • Press the F10 key to save the changes and exit BIOS.
  • Select yes and press Enter.
  • Complete the recovery
  • After the computer restarts, a series of startup screens appear. Complete Microsoft Windows setup as follows:
  • Complete the registration process, and then reconnect the devices that were disconnected earlier.
  • Reinstall software that did not originally come with the computer.
  • Write data files that were previously saved on the backup CD or diskette you made from the hard disk.

Jul 04, 2008 | Computers & Internet

Not finding what you are looking for?
HP TouchSmart IQ770 PC Desktop Logo

658 people viewed this question

Ask a Question

Usually answered in minutes!

Top HP Computers & Internet Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18394 Answers

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Tony

Level 3 Expert

2600 Answers

Are you a HP Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...