What is the easiest way to configure a website to make sure that the menus remain on the side and people can scroll up and down and not lose the menus.. so they can easily navigate back without hitting the back button..?

Not sure if you just want to print a configuration or if you have an error code. To print a configuration page

1. Scroll to and touch the Administration button.

1. Open the following menus:

1. Reports
   

• Configuration/Status Pages
  

• Configuration Page
  

Touch the Print button to print the report, or touch the View button to view the report on the screen. The report consists of several pages.


I

There are three ways of configuring IP address on any HP Printer:
A.- Using the control panel
B.- Using the web server
C.- Using the Jet Admin Utility
We'll deal with the contro panel setup.
To access the contro panel menus
1. Press OK (Check Mark) button once to access MENUS.
2. Press Up Arrow or Down Arrow buttons to navigate the listings.
3. Press OK (Check Mark) button to select the appropriate option.
4. Press Return to return to the previous level.
5. Press OK (Check Mark) button to exit the menus
So to configure IP address:
Press Check Mark
Navigate to the CONFIGURE DEVICE Menu using Down Arrow (the menu scrolls, so you may use any combination of Up/Down arrows)
Navigate to the I/O Menu
Navigate to the EIO 1 menu
Navigate to TCP/IP
Navigate to BootP entry
Press Check to disable it (Off)
Press return
Navigate to IP Address, press Check
Use Up/Down buttons to change the address, check to move between octets.
When finished, press Return
In the same way, enter Mask and Default Gateway
Press Return until you are out of the Menus.
Done

enter setup and load default configuration and save change.
hope this help

Hi

error code #10 is shown when the device can not be properly addressed and started.

OK, here is what we are going to do. First, uninstall the device from
Device Manager (Start-Run-devmgmt.msc). Now, uninstall the D-Link
Software from Add/Remove Programs in the Control Panel. Now reboot,
then get the latest drivers from D-Link's website. I am linking you to
the drivers for the D-Link DWL-650 (not DWL-G650), but you need to make
sure you have the exact model and firmware version correct. If it is a
different version, go to <a style='text-decoration: underline;' href="http://support.dlink.com" target="_blank">http://support.dlink.com</a> and use the drop down
menus to pick it.

Once that is installed, we are going to disable the Wireless Zero
Configuration Service. Click Start-Run-Type services.msc and click OK.
Scroll down to the bottom, right click on Wireless Zero Configuration
and click Properties. Stop the service and set it to disabled. Click
OK and close that. Now open the D-Link Configuration Utility and
configure it from there.

this might be what you're experiencing.......
Park Tilt Mirrors
If the vehicle has the memory
package, the outside mirrors
have a park tilt feature. This feature
automatically tilts the outside
mirrors to a preselected position
when the vehicle is in R (Reverse).
This allows the driver to view the
curb for parallel parking.
The passenger and driver mirrors
return to their original position
when the vehicle is shifted out of
R (Reverse), or the ignition is turned
off or to OFF/LOCK.
This feature can be turned on or
off through the Driver Information
Center (DIC)

The audio system controls are used
to access the personalization
menus for customizing vehicle
features. (DIC)
CONFIG (Configuration):
Press
to access the Configuration
Settings Menu.
MENU / SELECT Knob:
Press the
center of this knob to enter the
menus and select menu items.
Turn the knob to scroll through the
menus.
0
BACK:
Press to exit or move
backwards in a menu.

Sure hope this helps!
Best to you.

Press Check mark (SELECT button) to open the menus.
2. Use (UP button) or (DOWN button) to scroll to CONFIGURE DEVICE menu, and then press
(SELECT button).
3. Use (UP button) or (DOWN button) to scroll to I/O submenu, and then press
(SELECT button).
4. Use (UP button) or (DOWN button) to scroll to EMBEDDED JETDIRECT MENU
5. Use (UP button) or (DOWN button) to scroll to TCP/IP
Then: Select whether the TCP/IP protocol
stack is enabled or disabled. You can set several
TCP/IP parameters.
Select the TCP/IP CONFIGURE METHOD to
configure the EIO card. For the MANUAL option,
set the values for IP ADDRESS , SUBNET
MASK , LOCAL GATEWAY, and DEFAULT
GATEWAY

Per HP's site:
Do one of the following depending on whether the cleaning kit has been replaced or not:

• If NEW CLEANING KIT appears on the control panel display, use Up button and Down button to scroll to YES or NO, and then press SELECT. The kit life count is then reset.
• If NEW CLEANING KIT does not appear, press SELECT to open the menus. Use Up button and Down button to scroll to CONFIGURE DEVICE, then RESETS, and then RESET SUPPLIES. Scroll to NEW CLEANING KIT, and then select YES to reset the count.

Hi Friend,
To resolve the smeaing issue:

1. Set the Fuser Mode for the Envelope to High 1 or High 2.
2. Press Select (check mark button), and scroll down to CONFIGURE DEVICE.
3. Press Select, and scroll down to PRINT QUALITY.
4. Press Select, and scroll down to FUSER MODES.
5. Press Select, and scroll down to ENVELOPE.
6. Press Select, and scroll down to HIGH 1 or HIGH 2.
7. Press the MENU button to return to exit the menu and return to the Ready state.

Also,

1. Print a few more pages to see if the problem corrects itself.
   
2. Try using a different type of paper.
   
3. Make sure that the environmental specifications for the printer are being met.
   
4. Clean the inside of the printer and run a cleaning page to clean the fuser.
   
5. The printer might be due for maintenance. Check this by printing a copy of the supplies status page. If maintenance is due, order and install the printer maintenance kit.
   
6. Replace the print cartridge.
   

Perform a cleaning operation:
To run the cleaning page manually

1. If a duplexer is installed, open the rear output bin.
   
2. Press Menu to open the menus.
   
3. Use Product illustration (Up button) or Product illustration (Down button) to scroll to CONFIGURE DEVICE , and then press Product illustration (Select button).
   
4. Use Product illustration (Up button) or Product illustration (Down button) to scroll to PRINT QUALITY , and then press Product illustration (Select button).
   
5. Use Product illustration (Up button) or Product illustration (Down button) to scroll to PROCESS CLEANING PAGE , and then press Product illustration (Select button).
   
6. If a duplexer is installed, close the rear output bin.
   

Let me know the output

Regards,
Nikhil

Hi,
This could be a couple of things, easiest thing to try first is to put a different toner cartridge in, something that has already been opened because it would save you from opening a new one. Another thing you can try is sending a cleaning page through the printer to clean off excess toner from the fuser unit. What happens is over time toner builds up on the lower pressure roller of the fuser unit and after being heated and cooled so much the toner starts to flake off on your print outs. Follow these steps to try to clean the lower pressure roller:

To run the cleaning page manually
1.If a duplexer is installed, open the rear output bin.

2.Press check mark(SELECT button) or the MENU button to open the menus.

3.Use (UP ARROW button) or (DOWN ARROW button) to scroll to CONFIGURE DEVICE, and then press

4.Use or to scroll to PRINT QUALITY, and then press the check button

5.Use (UP ARROW button) or (DOWN ARROW button) to scroll to CREATE CLEANING PAGE for the(LJ 4200/4300) or PROCESS CLEANING PAGE if you printer is a(LJ 4250/4350) then press the check mark

6.Follow the instructions on the cleaning page to complete the cleaning process (LJ 4200/4300
only).

7.If a duplexer is installed, close the rear output bin.

This should help clear some of the flaking toner, if not you might have to replace the fuser unit.

You may have checked this already, but make sure your printer driver is not set up to print two copies per print job if it is then that's the easiest place to change settings. Or you can print out your printer's menu by doing the following: To print a menu map 1. Press (SELECT button) to open the menus. 2. Use (UP button) or (DOWN button) to scroll to INFORMATION, and then press (SELECT button). 3. Use (UP button) or (DOWN button) to scroll to PRINT MENU MAP, and then press (SELECT button) Look for anything that says "copies" and usually that will let you know what is set on the printer. To change a control-panel setting 1. Press MENU to open the menus. 2. Use (UP button) or (DOWN button) to scroll to the menu that you want, and then press (SELECT button). 3. Some menus might have several submenus. Use (UP button) or (DOWN button) to scroll to the submenu item that you want, and then press (SELECT button). 4. Use (UP button) or (DOWN button) to scroll to the setting, and then press (SELECT button). Some settings change rapidly if (UP button) or (DOWN button) is held down. An asterisk (*) appears next to the selection on the display, indicating that it is now the default. 5. Press MENU to exit the menu Good Luck.