Question about Pioneer Audio Players & Recorders

Open Question

The 6 amp, 500 volt fuse blew on my Pioneer SX-1010 receiver. I replaced it with a 250 volt fuse of the same length, but I still get no power at all. What to do? Where can I purchase a 500 volt fuse of the correct size? Thanks, Stuart. The fuse is 1 1/4'' long.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: Pioneer SX-203

Try taking the receiver apart and checking the fuses.

Posted on Mar 23, 2008

Ad
  • 2 Answers

SOURCE: car amp blows 12 volt wire fuse

the wire from your battery is blowing fuses? and you are using 20-30 A fuses? mine has a 100A fuse..look into getting new wire plus my wire is 4 gauge.., 1600 watts is too powerful for a 12 g wire and a 30 A fuse

Posted on Nov 18, 2008

  • 1 Answer

SOURCE: Pioneer receiver sx-315

With persistence, I was able to program the Universal Remote Control provided with the cable box to control my new used Pioneer SX-315 receiver. I now can control the tv volume, cable box, auxiliary stereo receiver with speaker system with one remote. Thank goodness I did not have to resort to buying a Pioneer remote control.

I was able to program another previously unused universal remote which I purchased several years ago. However, since the other remote control did not list the Vizio TV. That brand is too new for the remote.

Posted on Dec 07, 2008

  • 1 Answer

SOURCE: TEAC DIGITAL HOME RECEIVER AGD 8900 AV

I changed the diodos from power supply.
I thought that help you offered
was free,but I forget that nothing here is free.
Thank you anyway









Posted on Dec 15, 2008

  • 16 Answers

SOURCE: I need to replace the external fuse on a marantz Model 32 amp.

Well, take good look at the Fuse itself on metal area.
If it says AGC, then fast acting.
If it says MDL, then Slow Acting.

If you cannot figure it out, then just use Fast Acting since it is more commonly used in smaller Receivers and Amplifiers and Fast Acting will cutoff faster (compair to Slow Acting) if there is any unknown Prblem with Chassis.

Posted on Jan 31, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My pioneer stereo receiver model SX-240 blew fuse I unhooked all external wires but blows fuse turning it on what do I do?


Without seeing the unit in question, one really cannot say what the problem might be. I'd recommend you take it to an electronics repair shop.

Mar 21, 2015 | Pioneer Audio Players & Recorders

1 Answer

Put to big of a fuse in my pioneer sx-203 and burt out a cucit


Using a higher voltage fuse is not a problem, but if the fuse you used amps are to high, that is a problem. Sounds like a resister burnt. You have a short somewhere in that particular circuit, which is what took out your original fuse. . .your fuse did it's job by blowing and saving the circuit. If you can get your hands on a schematic, you can trace the circuit and find the short.

Jul 12, 2012 | Pioneer SX-205 Receiver

1 Answer

Hi I have a str-dh520 reciever that has a 8 amp 125 volt fuse that blew and I could only find a 8amp 250 volt fuse and when I installed it it blew right away. What do I do now? Dose it have to be a 125...


No! the fuse you replaced was fine, the power transformer may be shorted, or the audio ouput semiconductors are shorted, check the speaker wires for shorts, if okay! I recommend a pro with a estimate.

Mar 19, 2012 | Sony Audio Players & Recorders

1 Answer

Blown Fuse / SX - 205 / Pioneer reciever


Check the area where the fuse was...it's usually marked on the board or next to the fuse holder. Check the size also, 2 types 5x20mm or 1/4x1 1/4 in. Usually slow blow.

Mar 30, 2010 | Pioneer SX-205 Receiver

1 Answer

I have a Pioneer VSX-454 reciever, both 1.25 Amp fuses blown


blue two legged varacter on power supply board needs to be replaced

Jul 12, 2009 | Pioneer VSX-454 Receiver

2 Answers

Distorted sound coming out of SW channel only


try turnind down the sub from the amp itself it might be putting out more volts than the subs input can handle check your standing wave feature to make sure the trim is not up too high

Jan 13, 2008 | Pioneer SX-315

4 Answers

Pioneer SX-203


a little bit foolish thing: see if you have both the speaker channels (A and B) down. if you have both down it doesn't work - didn't for me.. and obviously make sure you have the right letter down - same outpout as your boxes

Dec 06, 2007 | Pioneer SX-205 Receiver

1 Answer

Years of good service...now it keeps blowing fuse


The voltage of the fuse is not the issue. It sounds like you may have some blown internal transistors (probably in the output area). Time for a trip to the repair shop I'm afraid.

May 18, 2007 | Sony STR-DE525

Not finding what you are looking for?
Audio Players & Recorders Logo

Related Topics:

85 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pioneer Audio Players & Recorders Experts

 Grubhead
Grubhead

Level 3 Expert

5151 Answers

John
John

Level 2 Expert

509 Answers

T-Comtech Repairs
T-Comtech Repairs

Level 2 Expert

417 Answers

Are you a Pioneer Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...