Question about Bosch 24 in. SHU43 Built-in Dishwasher

1 Answer

Does not complete its cycle. It hangs on "1" minute.

The dishwasher does not complete its cycle. It hangs with "1" on the display and continues to run. It does not complete rinsing the dishes or dry them.I get a diagnostic code of E1 which is a heating error.

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 523 Answers

Have the board and heater changed

Posted on Jun 02, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How can I reset our dishwasher

Open the dishwasher door sufficiently to see the control buttons, then hold the two buttons with labels "Cancel Drain" and press for 3 seconds.
Close the door. Wait nearly 1 minute for the dishwasher to complete the cycle.
Open the door and hold the "ON/OFF" toggle.

Reset Bosch Ascenta Dishwashers
Shut off the child lock if needed by pressing and holding "Open the door far enough to see the keys, then hold the "START RESET" toggle until the "ACTIVE" LED become extinguished. On the SHE5AM model of Bosch Dishwashers, hold the "START RESET" key until the display clock shows "0:01".
Close the door and rest about 60 seconds. On the SHE5AM, wait until the display clock displays "0:00".
Open the door and hold the "ON/OFF" toggle.

Apr 06, 2016 | Bosch SHE4AP06UC Dishwasher

1 Answer

Reset button maytag dishwasher

  • 1 Open and close the dooricon1.png of your Maytag dishwasher.
  • 2 Locate the "Rinse" button on the dishwasher control panel. Press and release the button five times in quickicon1.png succession.
  • 3 Press and release the adjacent "Drain/Off" button on the control panel two times; this will deactivate the dishwasher's demo mode and reset your dishwasher.
  • If you need to restart your dishwasher or forgot some dishes and want to open it during a cycle and restart it

  • 1 Press the "Cancel Drain" button on the display. Allow about 2 minutes for the dishwasher to completely drain.
  • 2 Choose a cycle under "Cycles" on the panel.
  • 3 Select an option or options under "Options" on the panel.
  • 4 Push the "Start Resume" button.
  • Oct 24, 2013 | Dishwashers

    1 Answer

    My gaggenau dishwasher GM 954-110 is not working. when i switch it on the display panel shows 2H.

    Hello, welcome to FixYa.

    The dishwasher you're speaking of (provided it is indeed a Gaggenau GM954) is built by Bosch as you may or may not know.

    To address your concern regarding the 2H in the display actually needs to be done in two parts. I'll start with the basic info associated with the 2H displayed.

    This can be simply indicating the previous cycle exceeded a 2 hour wash cycle, not necessarily an error and can be attributed with too cold water entering the dishwasher (below the recommended 120F), a longer than normal drain time (due to partial blockages, kink etc. hence longer time needed to complete the cycle) or inproper water circulation during the cycle.

    Aside from these issues, it (2H) can also mean the unit has a heating error and if left long enough will show another error of "1" in the display, extremely long wash times, etc.

    **The first thing I'd suggest before attempting any repair is running an additional cycle while making sure the water inlet is hot (120F optimum) and the unit does indeed drain fine.

    **A fair indication of proper draining is to start a cycle and once washing begins (2-3 minutes) activate the "cancel" and the unit should adequately drain in the 2 minute time allowance.

    **To identify proper water circulation, place an empty cup in the upright position in the top rack, start a cycle and inspect the cup after 2-3 minutes and it should be full of water.

    After trying and posting the results of these thing's we can move forward with potential heating errors, the cause, and how to remedy them. Let me know what you find and I'll continue to assist you in any manner possible going forward. Good luck.


    Macmarkus :)

    Jun 30, 2011 | Dishwashers

    2 Answers

    How do you disable the cycle completion signal/beep on the Bosch SHU9915UC dishwasher?


    Welcome to FixYa.

    I think can answer your question..."How do you disable the cycle completion signal/beep on the Bosch SHU9915UC dishwasher?"

    Follow these steps...

    **How to Operate the Cycle Completion Signal**

    1. Open door, hold down program button (see
    Beeper Table below) and simultaneously turn the unit "ON".

    MODEL Program BUTTON

    SHU 9950 Delay Start Hours
    **SHU 9910-9920 Delicate/Econo** should be yours
    SHU 8800/8810 Quick Wash

    SHV 6800 Delay Start Hours
    SHV 4800 Delicate/Econo
    SHV 4300 Delicate/Econo

    2. Release program button.
    a. For SHV 6803 and SHU9950 models:
    The display will blink with a code of "0", "1" or
    "2". You are in program mode.

    • If the display blinks with a "0", you will hear
    no signal (indicates OFF).

    • If the display blinks with a "1", you will hear a
    LOW volume signal.

    • If the display blinks with a "2", you will hear a
    HIGHER volume signal.

    b. For all other models with the beeper

    • If the machine beeps, then the Cycle
    Completion Signal has been enabled.

    • When you push the button again and it does
    not beep, it means that the Cycle Completion
    Signal has been disabled.

    3. To change the program, press the program
    button until the desired setting is selected.

    4. Turn the Dishwasher off to take it out of
    program mode.

    * At the end of a wash cycle, the beeper will sound
    off two times, and again every 15 minutes until the
    dishwasher is turned off.

    Hope this answers your question and provides you with what you needed.

    Thank you for choosing FixYa and good luck.

    Please take a moment to rate the solution provided and a short testimony if you feel it's warranted, but also let me know if you require further assistance.


    Macmarkus :)

    Oct 07, 2010 | Bosch SHU9915UC Dishwasher

    1 Answer

    Dishwasher will not run through its cycle


    If the cycle doesn't complete, check these:

    Water-heating cycle Many dishwashers heat the wash and/or rinse water to a higher temperature, as the cycle calls for it. In these cycles, the dishwasher pauses after it has filled with water, waiting for the water to reach the pre-set temperature. What happens next, depends, as follows:

    • On some units, the pause is timed and the unit continues after the allotted time.

    • On others, the cycle can't continue until the water reaches the higher temperature. If you have this type of dishwasher and the water isn't being heated (say, because of a problem with the heating element or thermostat), after the unit stops at the heating cycle, it never continues. When you repair the heating-system problem, the "cycle problem" is fixed too.

    Timer Timers don't often fail. But if every other part of the dishwasher seems to be working properly and the timer knob seems to be stuck in one place--doing one function continuously--the timer may be at fault. Dishwasher timers can't be repaired. If yours is defective, replace it.

    Please revert for further assistance and Do rate the solution as "FixYa" if found useful.


    Mar 26, 2009 | Dishwashers

    1 Answer

    Whirlpool gold dishwasher gets stuck at 53 minutes left for an hour

    Try "resetting" the control board by running the diagnostic cycle. The cycle completes in 15 minutes. 
    The details are in the service manual. The manual can be found hidden behind the tow plate (at the very bottom front of the washer).
    The diagnostic cycle may tell you the problem. It also helps clear up some of the software gltiches. 
    It is easy to run the diagnostic cycle.
    Just the buttons in the following sequence. The sequence should be complete within 6 sec. 
    heated dry -> Normal -> heated dry -> Normal
    This will trigger diagnostic cycle of 19 intervals. Pay special attention to the intervals 18, 17, 9, 6, 4.
    Interval 18 - displays your controller module number (should be letter 'd' followed by number 0 or 1 or 2 or something. Note that down for future reference.
    Interval 17 displays 'software generation number' Note that down for future reference.
    Then wait until you reach interval 9.  --- clean LED turns on - then an open or shorted thermister is detected.
    -- Sanitized LED turns on - then the washer detected greater than 100 deg F temperature
    Interval 7
    -- Soaking/sensing LED should NOT come on (unless food soil is present).
    Interval 4 -- Soaking/sensing LED should come on

    Let the cycle complete and then try running the normal wash. Hopefully the possible glitches are cleared by now and you should have no problem. 
    If this doesn't work, time to call the expert tech. 

    Nov 08, 2008 | Whirlpool Gold 24 in. Built-In Dishwasher...

    1 Answer

    Error code 2H

    The control panel needs to be replaced (indicated by the "2H" error code displayed at the start of the cycle).
    BTW - The number 1 displayed at the end of the cycle indicates the cycle has timed out (i.e., it doesn't mean 1 minute remaining). Hence the continued running of the unit. Until you replace the control panel, you'll have to manually cancel the cycle at this point.

    Oct 08, 2008 | Bosch 24 in. SHU53 Built-in Dishwasher

    1 Answer

    Kenmore model 665 dishwasher

    the timer is bad.the 42 min cycle and the 6 min cycle share the same timeline.try for the part number and price.installing the timer isnt that difficult.

    Jan 05, 2008 | Kenmore 24 in. 16304 Built-in Dishwasher

    4 Answers

    Whirlpool GU2400

    Yes I have a similar problem... GU2455XTSQ3 whirlpool gold. Hangs up at 52 minutes accompanied by a loud humming that lasts for 1/2 hour to 45 minutes? Then for whatever reson the cycle will continue and complete! This just started 6 months after purchase. Any ideas?

    Mar 11, 2007 | Whirlpool GU2400XTP Built-in Dishwasher

    Not finding what you are looking for?
    Bosch 24 in. SHU43 Built-in Dishwasher Logo

    979 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Bosch Dishwashers Experts

    Donald DCruz
    Donald DCruz

    Level 3 Expert

    17130 Answers

    Gerry Harvey
    Gerry Harvey

    Level 3 Expert

    1467 Answers

    Les Dickinson
    Les Dickinson

    Level 3 Expert

    18408 Answers

    Are you a Bosch Dishwasher Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides