Question about Dishwashers

1 Answer

Replaced the control board of my quiet partner

Replaced the control board of my 5 year old Quiet Partner II dishwaser. That did not fix the problem, and now it still won't complete a wash cycle. It stops after the wash, and the clean light flashes intermetently.

Posted by on

  • DOUBBLEJ34 Jun 02, 2010

    is it wp

  • keith100 Jun 03, 2010

    Yes, it's a Whirlpool, Quiet Partner II.



1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.


    An expert whose answer got voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 56 Answers

Clean light flashing is a power interuption between the heater and the control often its is actually the door switches from not closing the door evenly but a chance that the heater is bad.also if you replace the main ccu it should have a software update that buypasses the fault and a good start wouldd be to reverse the door switch and test your heater for ohm values you want it to ohm out

Posted on Jun 02, 2010

  • stephen hughes Jun 04, 2010

    also it is important for the water going into the unit to be 120 degrees if the water is to cold it will default out the water didnt get hot enough odds are it is in the door switches. there is two and one comonly doesnt make a contact if you reverse the two it sometimes takes care of the problem



1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Lock light stays on my whirlpool quiet partner II

If pushing and holding the lock button till the light goes out doesn't work, you likely have a problem on the circuit board.

May 24, 2014 | Dishwashers

1 Answer

Whirlpool quiet partner ii dishwasher has quit working. Power is getting to the dishwasher but it is not coming on at all. There is water standing in the bottom of it and a very foul smell is present.

This dishwasher has a thermal fuse that attaches to the main control board that may have failed, it can be tested with a meter for continuity if it does not have continuity then it is your problem.

Apr 21, 2012 | Whirlpool Dishwashers

3 Answers

I have a whirlpool quiet partner ii keeps stopping

DON'T REPLACE THE WHOLE BOARD!!! Are you kidding me? These other answers are a joke. I know exactly what is wrong because I had the same exact problem. I had the same problem with the same dishwasher. Get to the control board panel behind the keypad (from the inside of the door). Look at all the capacitors. If any of them have a top that is convex (bubbling out), then they need to be changed. I had two capacitors that were bad (right next to each other). i ordered the same ones on for $5. actually i got a 10 pack. unsoldered old ones. soldered new ones in. works perfectly. these models have a poor electronic board design or a poor overall design that blows these capacitors. Such an easy fix. I read so many internet threads where so many people with the same exact problem and replaced the whole board for $120 minimum if they did it themselves. silly. CHECK ALL THE CAPACITORS FIRST. 95% OF THE TIME when electronics go bad, its a bad capacitor, usually one that deals with the overall power. ~cheers

Jan 24, 2012 | Whirlpool Dishwashers

1 Answer

Whirlpool Quiet Partner II not washing or sensing.

I have a whirlpool quiet partner II and for some reason it does not drain the water out any more and I cannot figure out why....people say that it is the filter but that is unbelievably hard to get to and I cannot find any instructions online or paper work that tells how to break it down. If anyone has any insight please let me know

Nov 16, 2008 | Whirlpool GU2400XTP Built-in Dishwasher

1 Answer

Whirlpool Quiet Partner 980

Bad control board ,replace it.

May 26, 2008 | Dishwashers

26 Answers

Whirlpool Quiet Partner II

press back and forth between hi-tempwash and sani rinse several times to get all lights to come on if not then press sani rinse and heated dry back and forth several times. one of though combos will start the test mode. the test mode will stop the light from blinking and you can use the dishwasher again

Nov 26, 2007 | Whirlpool GU2400XTP Built-in Dishwasher

Not finding what you are looking for?
Dishwashers Logo

Related Topics:

229 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dishwashers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers


Level 3 Expert

76691 Answers

Brad Brown

Level 3 Expert

16043 Answers

Are you a Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides