Question about Televison & Video

2 Answers

Have a euro vox satellite box,is not working says its searching for codes i,ve followed instructions as b4 and normally no problems but today,tried to reprogramme and u see as usual the stations being downloaded on screen then it go,s to wait data being saved,then it goes to ch 1 discovery and banner comes up like its always done please wait code being updated and there it stays,as my eurovox v been zapped by ntl

Posted by on

  • scandal Apr 09, 2008

    hi paul,my box came already chipped,however mt partner phoned lsat night and i bought her one for xmas and hers has gone off as well i,m wondering if ntl as done something in the is fine with channels but it cimes up please wait to save data and thats it,it stays like that


2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has answered 1,000 questions.

  • Master
  • 3,422 Answers


Click HERE for some usefull info.

I hope this helps.

Please don't forget to rate the solution.

Posted on Apr 08, 2008

  • Priya darshan Apr 08, 2008

    Exactly... the problem is with the signals.Please go to the link which i gave you for more info.


  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Master
  • 4,102 Answers

It sounds like your not getting enough signal have you checked all leads are secure in the back of box

Posted on Apr 08, 2008

  • 2 more comments 
  • paul proctor Apr 08, 2008

    Also do you have a card thats usually in the sat if so then turn if at power remove card and leave off for an hour or 2 then this should reset the sat box hopefully solving your problem.
    I know when i had problems with mine i had to wait 30min for it to come back on after i lost all my channels so have you left it this long and see what happens or does this make no differance

  • paul proctor Apr 09, 2008

    Hi yes this can be a problem with downtime in certain areas our area was out for about 3 days a couple of months ago but im with virgin media.
    Have you tried going onto their website then they should give you the areas that are having problems they do on virgin what country are you in and area and ill see what i ca find out for you ok

  • paul proctor Apr 09, 2008

    Also by chipped do you mean your getting the channels for free you know your with ntl is that telewest as im in uk and our was telewest then virgin media bought them out and and changed to virgin media then the chipped setups stopped working and had to get reprogrammed for virgin media setup ill see what i can find out for you ok but give me country and region as it make it easier for me

  • paul proctor Apr 09, 2008

    Menu/Installation/User Installation and press the red button to Update
    Channels. The screen will go blank for a couple of minutes but this is
    perfectly normal. When this completes go to Sly Sports 1 and the
    updating code message will be there for anything up to 10 mins.

    This should sort your prob but if not let me know


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers


In your packet there should be a set up sheet for the remote when you try to set it up follow the search guide for the remote to search and find the comcast box. Depending on how the search works on that remote it may take some time and you may find more than one setting that will work. Then you have to choose the best one that operates the comcast box the best. Good luck and be patient.

Oct 14, 2009 | Televison & Video

3 Answers

Channel search only picks 9 channels

it depends on the frequencies supported by the television

other channel supplier putset top box and antenna so they can get the frequency

so its normal

Oct 31, 2008 | Televison & Video

1 Answer

Need codes for euro vox for 16th march

try downloading from
new codes for eurovox max v. code valid after code roll 29/11/08

its a free torrant site easy to use.

Mar 16, 2009 | Apex Digital Televison & Video

1 Answer

HDMI interface issues

If you swapped directv receivers and the problem followed to a different tv then there is something wrong with the directv receiver. Need to run satellite setup again on this receiver to fix. repeat satellite setup is accessible through the setup submenu by pressing menu from the directv remote. look under satellite submenu once in setup

Dec 23, 2008 | JVC HD-52Z575 52" Rear Projection...

1 Answer

Eurovox searching for updates

press menu then yellow you then need to type in the following letters and numbers
press menu then the yellow button then type in the following
5a 01
98 b0 ba 52 d3 21 08 b4
d2 ea 29 b7 b5 52 e9 ad
then press ok then exit

Nov 30, 2008 | Televison & Video

1 Answer

I have an RCA universal remote and I need a code for a Bell ExpressVu satellite in order to use the remote for both my TV and Satellite.

004 was the only code I could find for Bell but i do not think it will work. Therefore, i recommend the following:
Programming a Device using Code Search:

  1. Manually turn ON your device (TV, VCR, Cable Box)
  2. Press and "HOLD" CODE SEARCH
  3. Press and release the device button you want to set up (TV, VCR, Cable Box) However, if you are using AUX for a device, press and release AUX first and then the device button for the type of device to be programmed (TV, VCR, or Cable). The selected device button will flash once.
  4. Release CODE SEARCH.
  5. Press OFF/ON repeatedly until the device turns off (you may have to press up to 100 times at a rate of once per second).
  6. Once the device turns off, press and release ENTER.
  7. With the device on, press any other button. If the device responds, no further programming is required. If the device does not respond, repeat steps 1-6.

Jun 26, 2008 | Televison & Video

1 Answer

Need set up instructions and codes for one for all remote urc-3220

If your device does not respond to the remote control after trying all codes
listed for your brand, or if your brand is not listed at all, try searching for
your code.
NOTE: Before performing a code search for a DVD player or a VCR, turn on the device and
insert the required media.
For example, to search for a code for your TV:
1. On the remote control, press TV once.
2. Press and hold SET until the LED (red light) blinks twice,
then release SET.
3. Enter 9 - 9 - 1.The LED will blink twice.
4. Aim the remote control at the TV and slowly alternate
between pressing POWER and TV. Stop when the TV turns off
(after pressing POWER). If the device does not have a Power
key, you can substitute another function, such as digits 0 ~ 9 ,
CH+, or PLAY).
NOTE: In the search mode, the remote control will send IR codes from
its library to the selected device, starting with the most popular code
5. To lock in the code, press and release SET.The LED will
blink twice.
6. To search for the codes of your other devices, repeat steps
1 through 5, but substitute the appropriate device key for
the device you are searching for.
If you have set up the remote control using the Searching For Your Code procedure
as above, you may need to find out which four-digit code is operating
your equipment. For example, to find out which code is operating your
1. On the remote control, press TV once.
2. Press and hold SET until the LED (red light) blinks twice,
then release SET.
3. Enter 9 - 9 - 0.The LED will blink twice.
4. To view the code for the first digit, press 1 once.Wait 3
seconds, count the LED blinks (e.g., three blinks = 3) and
write down the number in the leftmost box in the TV
code boxes on page 8.
NOTE: If a code digit is “0”, the LED will not blink.
5. Repeat step 4 (on the previous page) three more times for
remaining digits.Use 2 for the second digit, 3 for the third
digit, and 4 for the fourth digit.Write down the code digits
in the remaining TV code boxes on page 8.
6. To check for codes of other devices, repeat steps 1
through 5 (starting on the previous page), but substitute
the appropriate device key for each device you are checking.
Write down the device’s code digits in the appropriate
code boxes on page 8.
I could not find the codes but you can follow these instruction to program without codes

Jun 19, 2008 | Televison & Video

1 Answer

53sbx59b Hitachi 53 inch proj tv

Call the 800 number with the new remote. Sometimes they will have additional codes. Or with the instructions with the new remote you can manually get it to work. You must follow instructions carefully. Look for this section in the instruction booklet

Dec 29, 2007 | Hitachi 53SBX59B 53" Rear Projection...

Not finding what you are looking for?
Televison & Video Logo

Related Topics:

54 people viewed this question

Ask a Question

Usually answered in minutes!

Top Televison & Video Experts

The Knight
The Knight

Level 3 Expert

71006 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

6694 Answers


Level 3 Expert

66126 Answers

Are you a Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides