Question about Furuno 000 144 601 Display Adaptor Cable

Open Question

I have an 8 pin airmar c32 transducer cable wired in my boat i think it is for a furuno what can i get that would plug into that

Posted by on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
TechnoMarine
  • 132 Answers

SOURCE: My new furuno LS6100 powers up but nothing happens except a quick

probably a bad ducer, very common. try a new ducer dangling over the side to confirm diagnosis before rigging!

Posted on Jan 16, 2010

Ad
TechnoMarine
  • 132 Answers

SOURCE: i have a furuno fcv 585 and have an airmar 1kw

no, the ducer should have the diplexer built in to it.

the matching box is for bare wire ducers.

Posted on Aug 04, 2010

TechnoMarine
  • 132 Answers

SOURCE: I have a furuno FCV295

If you reset it and while in the Initial Settings" Menu, you press menu, it should take you to the transducer setup screen. These menus allow for "Transducer Type" to be changed to your exact transducer. See the "Installation Manual", which is different than the "Operators Manual". Section 3 page 9 and 10. You may have to enter your units of measure (Knots vs MPH, etc), and then it will allow you to choose the transducer type. Hope this helps. John Barry, 847-746-0100, technicalmarine.com.

Posted on Jun 23, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

4 Answers

Furuno radar


Your antenna seems to be mis alighned. Its ZERO point must be readjusted.

Aug 30, 2008 | Furuno Navnet 1834C/NT vx2 Radar C Map Nt

1 Answer

WHAT TRANSDUCE GOES WITH THE DS600X COLOR ..WHERE CAN I BUY ?


Hi
Airmar makes almost all of the transducers for Raymarine. From the Airmar FAQ section, your unit is listed. See the link below. Pretty much any marine chandler or Raymarine dealer should be able to order it for you.

Hope this helps
-Steve
Airmar FAQ What Airmar transducers are compatible with the Raymarine...

Feb 26, 2015 | Raymarine Ds600x Digital Fishfinder With...

1 Answer

I have a furuno FCV295 and when I was doing the initial installation set up of the transducer (airmar r299) I accidently chose the wrong settings. How do I re-do the transducer settings? The factory reset...


If you reset it and while in the Initial Settings" Menu, you press menu, it should take you to the transducer setup screen. These menus allow for "Transducer Type" to be changed to your exact transducer. See the "Installation Manual", which is different than the "Operators Manual". Section 3 page 9 and 10. You may have to enter your units of measure (Knots vs MPH, etc), and then it will allow you to choose the transducer type. Hope this helps. John Barry, 847-746-0100, technicalmarine.com.

Jun 19, 2011 | Furuno FCV 295 104" Fish Finder

1 Answer

Does this transducer mount in the floor of the boat,or on the bottom of the hull?


Hi!

This transducer requires a hole to be drilled in the bottom of the hull and the unit installed from the outside, using a caulk/adhesive such as 3M 4200 or 5200. Nice choice. Furuno is a good manufacturer!

Hope this helps!

Dec 24, 2010 | Furuno 520 5psd Plastic Thru Hull...

2 Answers

GP700F Airmar P66 to TM260


you must run 50KHz for deep water, so you will have to solve the interference problem to benefit from the power

Oct 12, 2009 | Furuno GP7000F/NT GPS Receiver

1 Answer

I have a furuno fcv 585 echo sounder with a FURUNO CA50/200-12M -c13298 BRONZE THRU HULL HIGH PERFORMANCE TRANSDUCER. The transducer has 4 wires and it looks from the schematic that it attaches via a...


you need an MB1100 matching box has the 10 pin pigtail for your sounder and accepts bare wire input from your ducer
this will also ensure that all power from sonar get to ducer, but it from me if you like 847-746-0100

Jul 09, 2008 | Furuno FCV-582L GPS Receiver

1 Answer

Installation furuno GP7000F/NT


This unit has built in sonar, so no DFF1 is required. The 1KW transom mount is in stock here, with the proper Furuno 10 pin connector. That is all you need, the display, the power cord, the GPS antenna, the transducer and THE BOOK! We are a Furuno dealer in the Great Lakes

Mar 03, 2008 | Furuno GP7000F/NT GPS Receiver

Not finding what you are looking for?
Furuno 000 144 601 Display Adaptor Cable Logo

Related Topics:

282 people viewed this question

Ask a Question

Usually answered in minutes!

Top Furuno Boating Experts

Daniel Dollive
Daniel Dollive

Level 3 Expert

311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Shehu Pro
Shehu Pro

Level 3 Expert

1284 Answers

Are you a Furuno Boating Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...