Question about Maytag MAT13MN Top Load Washer

Open Question

I have a maytag legacy mod# sav515deww and the drum is starting to tilt and when it spins it sounds as if the drum is banging againt something.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
KOakaKO
  • 135 Answers

SOURCE: Maytag Washer Noise While Spinning

Most washer models have snap-clips holding the front of the top panel down, with hinge-like clips at the back. Carefully pry up the top panel on the front of the machine using a tool that won't scratch the finish, such as a plastic or wooden wedge. If it does not pop loose fairly easily, then carefully examine the back of the machine to see if this is a rare model that has screws holding down the top panel. (But really, it _should_ just pop loose.) Once the top panel is tilted up to expose the inside, you should be able to see everything you need to see inside the body to evaluate a spinning drum problem.

Posted on Aug 04, 2007

Ad
  • 1 Answer

SOURCE: My washer will not spin off the water

Just looked at mine the belt is broken.
You have to remove the motor and take the pump off to replace it.
28 1/4" x 1/2" Belt

Posted on Nov 12, 2008

SolutionGuy
  • 331 Answers

SOURCE: I have a Maytag Legacy gas dryer that won't heat

OK, Crispy... the con census is that the coils have failed. The coil kit you'll need is part number 279834 and can be either purchased on line or at your local appliance parts retailer.

{{{UNPLUG THE DRYER BEFORE PROCEEDING!}}}

The repair is easy, remove the lower service access panel by removing the two screws located on either side at the very bottom. Then rotate the panel toward you and pull it out.

At the bottom right, you'll see the gas valve. There are 2 round, black coils mounted to it. One of these has 3 wires going to it and the other has 2 wires. You'll also see that they are held down by a brass colored bracket. Remove the wires from the coils and then remove the brass colored bracket with a stubby (short) Phillips screwdriver. NOTE THE POSITION OF THE COILS AND NOTE WHERE THE WIRES GO!

Install the new coils and bracket them down. Install the wires to the coils. Now rebuild the unit.

Easy breezy. Even if you've never done this, you're looking at MAYBE an hour... maybe.

Hope this helps,
SG

Posted on Mar 25, 2009

  • 100 Answers

SOURCE: maytag legacy series is making a squeeking (sp?)

check idler pully

Posted on Aug 09, 2009

  • 1 Answer

SOURCE: Maytag Performa Washer spins out of balance

There was a recall on the washer base, which caused the unbalanced problem. Find Technical Buletin TDL-0050B-B issued by Matag.

Posted on Oct 09, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Maytag legacy series washer


The drive motor which spins the drum is connected to the drum by a rubber belt. Sounds like the belt is burned through. Make sure you can spin the inside tub by hand to verify that the tub can turn freely before you replace the belt. The hum is from the drive motor just spinning freely.

Sep 02, 2016 | Maytag Legacy Series Top Load Washer

1 Answer

During wash cycle of my Maytag Legacy SAV515DEWW, tub moves freely and after spin cycle, tub keeps spinning for a while.


Maytag has a drum brake located on the bottom of yor machine. You need to remove the brake and clean it up or perhaps replace the device.
Google Maytag washer drum brake for several "how to"sites

Nov 30, 2014 | Maytag Washing Machines

1 Answer

Clothes still wet


Usually due to blockage in filter or hose or pump, but may be motor brushes not spinning drum to proper speed

May 09, 2012 | Maytag Washing Machines

1 Answer

Drum bangs when spinning


How old is it? The dryer drum has plastic or teflon bushings that serve as bearings to keep the drum in place. After time they wear down, and the drum will wobble as it spins banging againt the cabinet. If you have the drum out to replace them, also a good time to replace the drive belt and the heating element if it's more than a few years old.

Jan 14, 2012 | Hotpoint Washing Machines

1 Answer

My Maytag washer model #:sav515deww is leaking underneath during the spin cycle. I took off the 2 front panels. I saw the water leaking from a large metal part that spins around. Its behind the motor and...


My Maytag washer model #:sav515deww is leaking underneath during the spin cycle. I took off the 2 front panels. I have been told taht it is a bearing and a seal that are out. Replacement parts cost approx $90.00. Unit is 5 years old. Is it hard to fix? Thanks

Dec 10, 2009 | Maytag SAV515DE Top Load Washer

1 Answer

NOISY DURING SPIN CYCLE


If this sound starts slow and gets faster till its helicopter sounding you probly have a verry worn spot on the drive belt when that spot goes around the pully it will thump the faster ti spins the more frequent the sound If you tilt the washer back you should be able to see the belt to examine it if this the problem
replace the belt
Hope this helps
please leave feedback

Nov 27, 2009 | Maytag Legacy Series Top Load Washer

1 Answer

My Maytag Legacy SAV515DEWW does not drain and spills over..


Well, turn the water off, install the old brakes (or wait for the new), and run the unit through a cycle (without clothes) to pump all the water out.

With the new brakes installed, and the drum empty of water, turn the water back on, run the unit through a cycle to confirm all works properly. If not, make the additional needed repairs before proceeding. If it works fine, then your good to go and start washing clothes again.

Jan 24, 2009 | Maytag Legacy Series Top Load Washer

1 Answer

The grinding (bearing) noise on "spin", now leaking rusty water under machine... 3 1/2 years old "Legacy" ??? NOT !


maytag has rear rollers and front drum glides when goes out sound like sand paper scratching, also inspect belt idler same noise

Aug 14, 2008 | Maytag Legacy Series Top Load Washer

2 Answers

Banging noise


You may have had a foreign object slip under a loose drum baffle. Manually rotate the drum to locate wwhich baffle it is in.

Apr 06, 2008 | Maytag Atlantis MDE7400AY Electric Dryer

3 Answers

Maytag Washer Noise While Spinning


Most washer models have snap-clips holding the front of the top panel down, with hinge-like clips at the back. Carefully pry up the top panel on the front of the machine using a tool that won't scratch the finish, such as a plastic or wooden wedge. If it does not pop loose fairly easily, then carefully examine the back of the machine to see if this is a rare model that has screws holding down the top panel. (But really, it _should_ just pop loose.) Once the top panel is tilted up to expose the inside, you should be able to see everything you need to see inside the body to evaluate a spinning drum problem.

Aug 04, 2007 | Maytag MAT13MN Top Load Washer

Not finding what you are looking for?
Maytag MAT13MN Top Load Washer Logo

Related Topics:

58 people viewed this question

Ask a Question

Usually answered in minutes!

Top Maytag Washing Machines Experts

Bill Long

Level 3 Expert

587 Answers

John Tripp
John Tripp

Level 3 Expert

4654 Answers

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Are you a Maytag Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...