Question about Hunter Ceiling Fan Light Remote Control

1 Answer

I have 4 fans all on same code how do i change

I have 4 fans all on same code how do i change them

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

You need to change the dip switches to different codes. Most likely it's a 1-4 small switches. Factory default is usually all on. Just change each fan to different positions and make sure you do the same with the matching remotes. The remotes must match the corresponding fans.

Posted on Jun 09, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Cant change remote code


Don't forget you have to change the codes in BOTH the receiver & transmitter.

Nov 30, 2013 | Hunter Ceiling Fan Light Remote Control

1 Answer

Reiker ceiling fan - does not turn on - theres is power to unit - maybe remmote is bad? how do i change code


Before trying to change the code, have you tried changing the batteries? Both in the hand held remote and the one in fan housing? If so, and that didn't help, make sure the batteries are turned in the right direction and fitting tightly.

Will the fan operate without using the remote control?

Feb 19, 2011 | Reiker Room Conditioner Heater

1 Answer

The remote for the master bedroom is controlling two rooms at once, how do I change the code on the fan.


You need to remove the faceplate that covers the remote sensor on the fan - this is likely to be at the very top, closest to the ceiling. You should find a small 'box' that will probably have two or three switches that can be placed in one of two positions. For example 000, 100, 010, 011 etc. Just change one of the switches to another position and that will then be a different code to the one set on your remote.

If you want to operate the fan that you have just change you will need another remote wit the same code that you have just set.

Jan 22, 2011 | Hunter (25417) Ceiling Fan

1 Answer

I have two fans in separate rooms but the remote works both fans at the same time.


There should be a set of very small switches that will change the code for each fan. Seems they must both be set to the same code. Re-set one controller and fan for one code and leave the other alone. Very small switches.

Aug 29, 2010 | Hampton Bay 24002 Ceiling Fan

2 Answers

Sometimes my hampton bay ceiling fan goes on by itself . It has a remote control switch only. It is a model 08060


you probably have a neighbor with the same remote .. each fan has a set of code switches on its receiver .. what ever code is selected by the little switches on the receiver (box in the fan) also must be set into the remote control (code switches in the battery compartment of the remote) .. either you or your neighbor will have to change their code ..different codes wont interfere with each other ... if the fan came with the remote control then the switches might be available on the top of the motor housing .. remotes that have been added on require that the lamp section be removed to get access to the receiver .. some older fans dont have a code selection .. the code is stamped on the receiver .. in that case then maybe your neighbor could change his code ...

once in a while a strong or local transmitter will interfere and set the fan on .. if you are near a radio transmitter, CB or ham radio ..

May 25, 2010 | Hampton Bay 24002 Ceiling Fan

1 Answer

Ceiling fan and light with remote turns on and off by itself


Both the remote and reciever in the fan base have the ability to have the codes changed. What is happening is you are getting radio interference that is causing the problem. Change the codes by either switching the switches in different positions or adding more dip clips that came with the fan. In any case change the codes in both the reciever and remote to the same code and you should no longer have a problem. Usually the place to change the code in the remote is in the battery area and are small switches (usually 5 or 6 of them) and unfortunately you will have to take the fan down to do the one there.

Oct 12, 2009 | Hunter 52" Ceiling Fan With Light And...

1 Answer

Two fans with the same remote code.


There are dip-switches in both the remote and the fan. You need to change the switches on one of your fans.

Jul 14, 2009 | Universal Remote Control Hampton Bay...

1 Answer

Ceiling fan with light fixture remote won't turn it off - help!


Think we've figured out that a neighbor has the same remote code as we do and we will have to change our code. (This fan is out on our screened porch and the homes are close together here.)

Oct 15, 2008 | Hampton Bay 54 In. 5-Blade Fan, Chestnut,...

1 Answer

Hampton Bay 46056 fan


I have three Hampton Bay Ceiling fans with remotes for eight years. I doesn't help when a neighbor buys the same make and model. So, I had to come up with a different code for mine. I had to change the code for the remote and match it with the code in the fan. To change the code in the fan, that depends on the type of fan you have, some you would need to look on top of the fan and use a skinny stick to change the code, other's you would need to take the light fixture down to get to the controller box to change the code. I have both types, this is how know. PS. if ever, which will happen, if the fan doesn't respond to the remote then you would need to replace the controller inside the fan. Here's the warrenty no. 800.749.3267 for replacement.

Dec 24, 2007 | Hampton Bay 46056 Callaway II Ceiling Fan

Not finding what you are looking for?
Dryers Logo

Related Topics:

175 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hunter Dryers Experts

Paul Bade

Level 3 Expert

1536 Answers

yadayada
yadayada

Level 3 Expert

75822 Answers

Brandon Berry
Brandon Berry

Level 2 Expert

407 Answers

Are you a Hunter Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...