Question about Canon (18x50) IS Binocular

Open Question

Problem with image stabilizer

I have canon IS 18x50 binoculars. I am having problem with its image stabilizer. when i try to put it on the green light blinks few times and turns off. Some time after trying few times stabilizer comes on, but it turns off after few mins. I have changed new batteries also but it worked for few mins and again started same problem. pLease help me in fixing this problem.

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 159 Answers

SOURCE: 12x36 only one eyepiece focus

Assuming you have already tried replacing the battery, contact Canon Service Dept.

Posted on Mar 22, 2008

SOURCE: Canon i560 printer

I have similar problem. I found this solution that may help you. My problem insists tho.

>>> 5 flashes indicates a faulty printhead or possibly a problem with the p/head contacts. Try removing the head which is easier if you take the cartridges out first(no tools required) and re-seat it having checked the contacts for dirt.

If that doesn't work it may be that the waste ink tank is full. Try this ...
Canon S9000, S300, S400, i550, i560, i850, i860, i865, i9100, i9950, PIXMA iP3000 above,
1. Turn off printer
2. Hold down Resume button and press Power button.
3. Keep holding down Power button and let Resume button go.
4. Press Resume button 2 times then let BOTH buttons go.
5. Green lights will flash and then stop blinking.
6. When green lights are solid, press the Resume button 4 times.
7. Press the Power button and the printer should turn off, if not, press the Power button once more.
8. Your printer should respond as normal.

Posted on Aug 12, 2008

  • 112 Answers

SOURCE: Our group has 2 pairs of Canon Image Stabilizer

when salt water gets in ..if its not cleaned soon then its probably to late...the cost of repair wuld be more than a new one...sorry...larry@reichinstruments.com

Posted on Aug 06, 2009

cene765
  • 787 Answers

SOURCE: Canon 1560 error - orange light blinking 5 times

It's mean "Print head not installed/Defective print head".First open cover and remove the ink cartridges.Then open holder and remove the print head.Clean the contacts on printer and print head using piece of cotton and some alcohol.Then put back all again.If the problem persist you need to replace the print head.It's part number now is QY6-0064, because the old QY6-0042 is discontinued.

Posted on Oct 30, 2009

  • 2 Answers

SOURCE: Canon 5D won't turn on

my 5D have same problem 2......how much$ if i sent my 5D to canon and replace the power supply unit?
thx

Posted on Jan 05, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need repair of Canon 15x45 IS binoculars


That is bad and I am surprised. Canon Canada is just down the street from me!

There are lots of binocular repairers here.


binoculars Google Search

Mar 06, 2017 | Zeiss Optics

1 Answer

My 18x50 IS binoculars are broken; the right eye piece won't focus and I hear a clunk inside when I turn it over; the left focuses just fine. What can I do and where; here in las vegas?


Sounds like you've dislodged one of the prisms inside. A service center can look it over for you, but from personal experience, it's cheaper to replace them than pay to ship them to/from the service folks plus the estimation fee just to find out that they'll have to be replaced, anyway. Sorry.

Jul 24, 2012 | Canon (18x50) IS Binocular

1 Answer

Techno stabil 14x40 . yellow light comes on. Green light wont follow. Pwr button will not turn off pwr . of course if gr does not come on no IS


Hi.

The binocular is behavior is the same as when the electronic control module is defective. First try resetting the electronics by pulling out and putting back the AA batteries. The power reset in some occasion may unlock a jammed control module. If you have an external power adapter also test the binocular using the power adapter.

If that does not help the control board must be replaced. Disassembling of optical units is quite delicate and require experience. In that case I suggest contacting Fuji to get support. You can also get a quote on repair from a third party service. Here the online form: Repair Form.

Here some contacts. You will find your local Fujinon contact on the user manual provided with the binocular:

FUJINON INC.
10 HIGH POINT DRIVE, WAYNE, NJ 07470 U.S.A.
TEL:973-633-5600 FAX: 973-694-8299

FUJINON (EUROPE) GmbH
2 HALSKESTRASSE 4, 47877 WILLIcH, GERMANY
TEL: 2159-528545 FAX: 21 59-51 315

See also : Technical Service

Regards.

Ginko

Aug 28, 2011 | Fujinon Techno-Stabi Binocular

1 Answer

Hello i have a zeiss 20X60 image stabilizer binocular, needs repair, are you zeiss dealer?


FixYa is an online advice site largely staffed by volunteers. They are not dealers in cameras or other items.

Nov 22, 2010 | Zeiss Optics

1 Answer

My Canon 10x30IS Image stabilized binoculars show a double image. Both sides focus and stabilize. Can I do something to fix it or should I send them in for repair?


Like I said before, one of the prisms has shifted and the binoculars have lost collimation. This is not something you can fix yourself.

Nov 18, 2010 | Canon IS (10x30)

1 Answer

WhenI turn on the camera, the green lights


The camera sounds like it needs repair.
Make sure that the battery is either full charged or has new batteries installed.
If the camera still cannot start, then call Canon Repair. Go to the 800j number, give them the model you have. If it is still under warranty, it may be fixed for free. repair

Oct 07, 2009 | Canon Powershot A1000IS 10MP Digital...

1 Answer

Image stabilizer stopped working on Canon 70-300mm lens


Taken that you made sure that the IS switch was on, on the lens, yes you have to find a camera repair shop to get it fixed.
The best shops are authorized Canon repair shops. You can call Canon support, and they should be able to give you advice on what shop to send the lens to.
I hope this helped!
/Chris

Oct 31, 2008 | Canon Cameras

1 Answer

12x36 only one eyepiece focus


Assuming you have already tried replacing the battery, contact Canon Service Dept.

Nov 18, 2007 | Canon (12x36) IS II Binocular

Not finding what you are looking for?
Canon (18x50) IS Binocular Logo

Related Topics:

85 people viewed this question

Ask a Question

Usually answered in minutes!

Top Canon Optics Experts

kakima

Level 3 Expert

102366 Answers

old marine
old marine

Level 3 Expert

1973 Answers

TC CAMERA REPAIR.Com...

Level 2 Expert

169 Answers

Are you a Canon Optic Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...