Question about Harley Davidson Harley-Davidson Motorcycle Desktop Telephone

Open Question

How do I put my 2008 Rocker C in service mode to remove the battery without the alarm going off when the battery is disconnected.

Posted by on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
OneRide
  • 379 Answers

SOURCE: how to put the alarm into service mode on xl883l

Unfortunately, the Harley alarm is VERY complicated to set up. It covers 10 pages in the owner' manual. Try and borrow or buy an owner's manual from the dealer. If you just need to turn it on or off, one long click (on the remote button) turns it on and 2 clicks turn it off.

Posted on Oct 10, 2009

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

I replaced the battery in my 2008 Chevrolet Colorado and the factory alarm aka my horn won't stop going off. How do I reset my alarm?


pull the horn relay till its sorted
factory alarm may need a diagnostic scanner
might be a faulty module

Apr 16, 2017 | Chevrolet Cars & Trucks

1 Answer

How to disconnect viper car alarm


Find your alarm module, it is a black, rectangular box with an antenna wire on one end. Remove any ties or fasteners holding the alarm in place and take it out from under the dash.
All you need to do is simply remove the two connected wires to the ignition switch, and connect it with the car side of the two together. This enables the ignition switch and that enhances the control over the starter again, without hindrance.
For further help and assistance contact Eurobahn BMW MINI Mercedes-Benz Audi of Greensboro.

Jun 10, 2017 | Viper Vehicle Parts & Accessories

1 Answer

Left lights on ,and ran down battery. When i try to jump start, alarm goes off,key fob wont work till battery charges tried putting key in ignition and turning key, tried locking and unlocking door. what...


Find the alarm and disconnect it, or locate the fuse to the alarm and remove it. Then you can charge the battery without all the noise. Once the battery is charged, hook the alarm up and disarm it with the remote.

Dec 28, 2010 | Kia Spectra5 Cars & Trucks

1 Answer

I disconnected the battery on my 2008 jeep liberty sport to install a radio and when I reconnected it I got an "error" message on the odometer that won't go away. I did install a pac to adapt for...


its because the radio was disconnected from the computer as the alarm system is run through the radio so it doesnt need a code putting in every time the battery is disconnected ,so as far as iam aware its back to the dealer to re programme the computer to remove it from the memory or the computer

Sep 19, 2010 | 2007 Jeep Liberty Sport

1 Answer

How to put bike into service mode to carry out work.


Hi Lincolnboy, for more information about your question please visit the websites below. Good luck and have nice day.
Set Change Override Transport Harley Security Alarm PIN Code No Key Fob...

Apr 23, 2010 | 2005 Harley Davidson FLSTC - FLSTCI...

1 Answer

Removal of battery


Hi .... On your fob you have a few options, you have to press the fob to place it in service mode.
1.Disarm
2.Turn ignition on
3.press and hold the smaller of the two buttons on the fob until you hear a beep.

This is service mode but you still get a beep every few seconds which will drive you nuts! It must have a backup battery built in because it continues even without the battery.

You can take it out of service mode by pressing the arm/disarm button.

Jan 04, 2009 | 1998 Yamaha TRX 850

1 Answer

Trying to remove my battery for a yahama trx 850 but my alarm keeps going of when i disconnect battery help


1.Disarm
2.Turn ignition on
3.press and hold the smaller of the two buttons on the fob until you hear a beep.

This is service mode but you still get a beep every few seconds which will drive you nuts! It must have a backup battery built in because it continues even without the battery.

You can take it out of service mode by pressing the arm/disarm button

Jan 04, 2009 | 1998 Yamaha TRX 850

1 Answer

1993 Toyota Pickup Alarm


Glad to be of service. The graciousness of a FIxYa rating would be most appreciated.

Dec 10, 2008 | 1993 Toyota Pickup

2 Answers

Factory Alarm won't stop once battery is replaced


put your key in the door and turn the key to either direction!!

Dec 07, 2008 | 2002 Chevrolet Cavalier Coupe

Not finding what you are looking for?
Lands Phones Logo

Related Topics:

99 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Lands Phones Experts

kakima

Level 3 Expert

102366 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6918 Answers

ted dux

Level 2 Expert

135 Answers

Are you a Harley Davidson Lands Phone Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...