Question about Peavey Valveking Head

1 Answer

No sound i have just bought the valve king 100 head and the cabnet. i have pluged a stero plug into the head and connected it into the cab. i have plugged the power cable into the head and a working power outlet. when i turn on the amp a big flash of light came from the head and i have yet to figure out how to get any sound. the red power light lights up but my guitar has not played a single note

Posted by on

  • Anonymous Mar 29, 2014

    New valve king 100 head and 4x12 cabinet. Need to know how to connect the two. No cables included with product other than power cord for head.

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Peavey Master
  • 5,603 Answers

You would NOT use a stereo cable to plug in your guitar.

The stereo cable would carry the battery voltage back to the amp and MAYBE cause the fuse to blow.

You use a MONO instrument cable for your guitar.

The ring connection is use to complete the circuit to turn on the battery in most guitars.

Replace the fuse ONCE and get the proper instrument cable (NOT consumer audio cable) for your guitar.

If fuse blows again, take amp to shop for service.

Posted on May 30, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

There is no sound coming out of my Marshall 100 watt tube amp head?


make sure the standby switch is operating correctly.Sounds like the power tube.

Dec 18, 2013 | Marshall Amplification Marshall JCM800...

1 Answer

Can i connect 2 (2x12) cabs rated @ 4ohms each to my avt50 head?


No, the ATV50 head is rated for 4 ohms total. Using both 4 ohm cabinets at once will fry your amp.

Feb 12, 2013 | Marshall Amplification Music

1 Answer

Can i connect 2 (2x12) cabs rated @ 4ohms each to my avt50 head?


No, the ATV50 head is rated for 4 ohms total. Using both 4 ohm cabinets at once will fry your amp. Your only option would be to rewire your cabs internally to 16 ohms each by connecting the speakers in parallel, but that would cut your amp's power in half.

Feb 12, 2013 | Marshall Amplification Music

1 Answer

HOW TO REPLACE BLOWN FUSE PEAVEY VAVALE KING 100 HEAD


Contact Peavey toll free at 877-732-8391 or by email at customerservice@peavey.com,

Jan 26, 2013 | Peavey Valveking Vk100 Guitar Head

1 Answer

I have a MG100HDFX head, with the cabinet that came with it and the other I plugged in, the amp sounded fine for about 5mins while i was warming up. Then it started to fade in and out with a very fuzzy...


I would first suspect the head... try driving a different speaker to isolate which is at fault.

If unit starts working when cooled down, it may be going into thermal protection due to any of several causes including a defect or overdriving it.

Nov 15, 2010 | Marshall MG100HDFX 100-Watt Amplifier Head

1 Answer

Pluged in but no sound comes out whats up?


Could be that the male plug isn't connecting in its recepticle, or perhaps an internal wire or other connection is broken. If nervous about looking inside and perhaps resolving the problem, take the guitar to a qualified repair shop

Jul 26, 2010 | Fender Frontman 212R 100W 2x12 Guitar...

2 Answers

Marshall Lead 100 Mosfet head, no sound.


are you popping fuses??? check the effects, preamp, and power amp jacks to make sure they (even if not in use) are Normally Closed. Sometimes they loose their contact to ground on the Tip of the jack, which opens the circuit and interrupts the normal function. then check the input jack for good contact to the pcb and solder joints, as well as all pots (especially the volume). if all this checks out, and it still is having issues, i would then move on to the grounding resistors (solder welds can heat up and break as these resistors get hot) and resolder them to the board. still no output, then diodes / rectifier / filter caps.

May 01, 2010 | Marshall Amplification Marshall MG250DFX...

2 Answers

Behringer djx700 pro 5 channel mixer


Always check your cables and connectors on them to make sure the cable is good and the connectors are not loose. This sounds like a bad cable or connection between the line output of your mixer and input to your stereo.

Apr 23, 2009 | Behringer DJx700 5-Channel Pro DJ Mixer...

Not finding what you are looking for?
Peavey Valveking Head Logo

240 people viewed this question

Ask a Question

Usually answered in minutes!

Top Peavey Music Experts

Michial Gueffroy

Level 3 Expert

1138 Answers

Ben Armstrong

Level 2 Expert

357 Answers

Vito Vacirca Jr.

Level 2 Expert

140 Answers

Are you a Peavey Music Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...