Kohler lawn mower engine, mod SV#6005, spec # SV 600-0003, ft lb of torque for head bolt, valvue lash.

Toyota 2c ...
USE NEW BOLTS...
Torque sequence:
You're driving a diesel single cylinder head engine. Engine head torque has to be done in specific order and stages if not can warp head or break bolts. Suggest you get torque sequence and torque specs from your Toyota dealer, they can give you correct answer. Don't trust answers on here, if you choose wrong specs. could end up messing up head.

Flywheel - Use a Sealer on bolt, Manual Transmission 88nm/65 ft lb... Auto Transmission 74nm/55 ft lb

Aug 06, 2014 | Cars & Trucks

1 Answer

Looking for cylinder head and connecting rod torque specs for a Kohler K582 engine

hi there

pauly 46 here

for your information required see the download of service manual from below

http://www.scribd.com/doc/3852484/K582-Service-manual

but i have the required settings for you in the mean time cyl hd bolts 35 ft /lbs

and con rod bolt torques 5/16 " use 200 in/lb torque

or if 3/8 bolts use 300 in/lb torques

service manual is 92 pages long but helpfull

cheers hope it hepls

pauly46

May 03, 2011 | Cub Cadet Garden

1 Answer

Need torque spec for head bolts on engine 10L902-0536-E2

150 in/lb or 12.5 ft / lb torque

other useful specs
oil is sae 30 0.6 litre or 600 mils
valve clearance is 0.005 thou and exhaust is 0.007"

cheers paul46

Sep 12, 2010 | Garden

1 Answer

NEED TORQUE SETTINGS FOR 18 HP MODEL 31H777-0297-E1. ROD BOLTS AND HEAD BOLTS. IS THERE A PATTERN TO TIGHTENING HEAD BOLDS

hi

con rod bolt torques are 150 in/lb or 12.4 ft/ lb

cyl head bolt torque is 220 in/lb or 18.5 ft/lb

here is website for parts and manual

http://www.briggsandstratton.com/maint_repair/manual_and_more/docsearch.aspx?enginelookfor=31h777-0297-e1

i would torque them in this sequence

start from bolt centre top , then bolt centre bottom, then bolt left upper , then bolt btm right, then bolt bottom left , then bolt upper right , then bolt centre left

should be 7 bolts 5/16 x unc

check out website its good so is www.partstree.com

cheers paul

Aug 16, 2010 | Briggs & Stratton Garden

1 Answer

We were wondering the torque on the head bolts on a Kohler motor for a lawn mower.

Hi and welcome to FixYa. I am Kelly. These torques are from the Kohler Service manual for the
CV11-16,
CV460-465,
CV490-495
engine.

There are 5 bolts.... as you look at the bolts there should be 3 on the left side

Bolt 1 is the center (offset bolt)
Bolt 2 is upper right
Bolt 3 bottom left
Bolt 4 upper left
Bolt 5 lower right.

Torque them in the sequence above... to 15 Ft lbs. or 180 inch lbs
reset your torque wrench and then torque them to 30 Ft lbs or 360 inch lbs.

Rocker arms center nuts (called mounting screws) are first torqued to 55 inch lbs then to 100 inch lbs.

Then to set the valve lash you back off the set screw lock nut torque and set the valve lash to .003 - .005 final set screw lock nut torque is 65 inch lbs. Engine must be at TDC i.e piston all the way to the top to make the correct adjustments.

Thanks for using FixYa.

Kelly

Jul 17, 2010 | John Deere Garden

2 Answers

Torque spec

Head bolt torque is 32 ft.-lb. (43 nm)
Head cover bolt torque is 7 ft.-lb. (10 nm)

Mar 25, 2010 | 2000 Yamaha Royal Star Venture

1 Answer

I have 4.9L6 need torque specs for cylinder head

for cylinder head the torque is : step 1 55 ft-lb, step 2 65 ft-lb, step 3 85 ft-lb. Rocker arm stud nut or bolt is 17 to 23 ft-lb. and valve cover bolt 72 to 108 in-lb.

Dec 05, 2009 | 1988 Ford F 150

2 Answers

Cylinder head torque specs

Cyl. Head Bolts torque

200in.lbs

16.5ft.lbs

22.5Nm

Mar 26, 2009 | Craftsman Garden

1 Answer

Head bolt torque specs needed for 96 tbird 3.8

Head bolts are torque to yeild so you MUST use new bolts.
Tighten cylinder head retaining bolts in numerical sequence in three steps as follows:

20 Nm (15 lb-ft).

40 Nm (30 lb-ft).

50 Nm (37 lb-ft)

Loosen retaining bolts one at a time two to three revolutions and retighten as follows:

Long bolts:

Tighten to 40-50 Nm (30-37 lb-ft).
Rotate an additional 175-185 degrees.
Go to next bolt in sequence.

Short Bolts:

Tighten to 20-30 Nm (15-22 lb-ft).
Rotate an additional 175-185 degrees.
Go to next bolt in sequence.

Here is a pic of the sequence
http://i253.photobucket.com/albums/hh43/chuck943/Headboltsequence38L.gif

Mar 19, 2009 | 1996 Ford Thunderbird LX

4 Answers

Torque specs for the cylinder head

2004 ENGINE
Engine Mechanical - 1.6L (L91) - Aveo
SPECIFICATIONS
FASTENER TIGHTENING SPECIFICATIONS
Fastener Tightening Specifications
Application
Specification
Metric English
A/C Compressor Mounting Bolts 27 N.m 20 lb ft
A/C Compressor Mounting Bracket Bolts 50 N.m 37 lb ft
Air Filter Housing Bolts 12 N.m 106 lb in
Alternator Adjusting Bolt 20 N.m 15 lb ft
Alternator Adjusting Bracket Retaining Bolt 20 N.m 15 lb ft
Auxiliary Catalytic Converter-to-Exhaust Manifold
Nuts and Bracket Bolts
40 N.m 30 lb ft
Camshaft Cap Bolts 16 N.m 12 lb ft
Camshaft Gear Bolt 67.5 N.m 49 lb ft
Camshaft Pressure Plate Bolts 10 N.m 89 lb in
Connecting Rod Bearing Cap Bolts 25 N.m+30°+15° 18 lb ft+30°+15°
Coolant Pump Retaining Bolts 10 N.m 89 lb in
Coolant Temperature Sensor 20 N.m 15 lb ft
Crankshaft Bearing Cap Bolts 50 N.m+45°+15° 37 lb ft+45°+15°
Crankshaft Position Sensor Retaining Bolt 10 N.m 89 lb in
Crankshaft Pulley Bolt 95 N.m+30°+15° 70 lb ft+30°+15°
Cylinder Head Bolts - Camshaft Support Housing
and Cylinder Head Mounting Bolts
25 N.m+60°+60°
+60°+15°
18 lb ft+60°+60°
+60°+10°
Electronic Ignition System Ignition Coil Mounting
Bolts
10 N.m 89 lb in
Electronic Ignition System Ignition Coil Mounting
Plate Bolts 10 N.m 89 lb in
Engine Mount Bracket Retaining Bolt 65 N.m 48 lb ft
Engine Mount Bracket-to-Engine Mount Retaining
Bolts
60 N.m 44 lb ft
Engine Mount Retaining Nuts 40 N.m 30 lb ft
Exhaust Flexible Pipe Bracket Bolts 40 N.m 30 lb ft
Exhaust Gas Recirculation Valve Adapter Bolts 25 N.m 18 lb ft
Exhaust Manifold Heat Shield Bolts 15 N.m 11 lb ft
Exhaust Manifold Nuts 25 N.m 18 lb ft
Flexible Plate Bolts 60 N.m 44 lb ft
Flexible Plate Inspection Cover Bolts 10 N.m 89 lb in
Flywheel Bolts 35 N.m+30°+15° 26 lb ft+30°+15°
Flywheel Inspection Cover Bolts 12 N.m 106 lb in
Front Muffler-to-Main Catalytic Converter Nuts 30 N.m 22 lb ft
Fuel Rail Retaining Bolts 25 N.m 18 lb ft
MITCHELL 1 ARTICLE - 2004 ENGINE Engine Mechanical - 1.6L (L91) - Aveo Page 1 of 330
http://www.eautorepair.net/app/PrintItems.asp?S0=2097152&S1=0&SG=%7BEEDCF... 3/30/2009
ENGINE MECHANICAL SPECIFICATIONS
Engine Mechanical Specifications
Intake Manifold Retaining Nuts 25 N.m 18 lb ft
Intake Manifold Support Bracket Lower Bolt-to-
Engine Block 40 N.m 30 lb ft
Intake Manifold Support Bracket Upper Bolts 25 N.m 18 lb ft
Lower Timing Belt Cover Bolts 10 N.m 89 lb in
Oil Pan Retaining Bolts 10 N.m 89 lb in
Oil Pressure Switch 40 N.m 30 lb ft
Oil Pump Retaining Bolts 10 N.m 89 lb in
Oil Pump/Pickup Tube and Support Bracket Bolts 10 N.m 89 lb in
Oil Pump Safety Relief Valve Bolt 36 N.m 22 lb ft
Oil Pump Rear Cover Bolts 6 N.m 53 lb in
Power Steering Pump Mounting Bolts 25 N.m 18 lb ft
Power Steering Pump Pulley Bolts 25 N.m 18 lb ft
Rear Timing Belt Cover Bolts 10 N.m 89 lb in
Spark Plug Cover Bolts 3 N.m 27 lb in
Spark Plugs 25 N.m 18 lb ft
Thermostat Housing Mounting Bolts 20 N.m 15 lb ft
Throttle Cable Bracket Bolts 8 N.m 71 lb in
Timing Belt Automatic Tensioner Bolt 25 N.m 18 lb ft
Timing Belt Idler Pulley Bolt 40 N.m 30 lb in
Transaxle Bell Housing Bolts 75 N.m 55 lb ft
Transaxle Brace Bolts 40 N.m 30 lb ft
Transaxle Torque Converter Bolts 65 N.m 48 lb ft
Upper Timing Belt Cover Bolts 10 N.m 89 lb in
Valve Cover Bolts 10 N.m 89 lb in
Application
Specification
Metric English
General Data
Engine Type 4 Cylinder - In-Line
Displacement 1598 cm3 97.51 in3
Bore Stroke 79.0x81.5 mm 3.1x3.21 in
Compression Ratio 9.5:1
Firing Order 1-3-4-2
Maximum Power - At 6200 RPM 77 kw/103.3 hp
Maximum Torque - At 3400 RPM 145 N.m 106.9 lb ft
Cylinder Bore
Diameter 79 mm 3.1 in
Out of Round - Maximum 0.0065 mm 0.00025 in
Taper - Maximum 0.0065 mm 0.00025 in
Piston
MITCHELL 1 ARTICLE - 2004 ENGINE Engine Mechanical - 1.6L (L91) - Aveo Page 2 of 330

Jan 07, 2009 | 2004 Chevrolet Aveo

Not finding what you are looking for?

View Most Popular

Pro Lawn Tractor 2006 and Newer Ground Drive Mower Belt

Garden

Toyota 2c. I need cylinder head and flywheel Torque settings

Cars & Trucks

Open Questions:

0 Answers

bent pushrods on 20hp v twin briggs lawn trator

May 22, 2014 | Poulan Pro Lawn Tractor 2006 and Newer...

0 Answers

replacing a carburetor on a lawn tractor

Jul 07, 2012 | Poulan Pro Lawn Tractor 2006 and Newer...

0 Answers

replace the Arm Assembly Pad Break part # 131845x900 on poulan lawn tractor mower deck

Jun 28, 2012 | Poulan Pro Lawn Tractor 2006 and Newer...

0 Answers

pxt 12530 manual looking for manual for poulan xt lawn tractor model pxt 12530

Jun 11, 2012 | Poulan Pro Lawn Tractor 2006 and Newer...

See all Poulan Pro Lawn Tractor 2006 and Newer Ground Questions

Ask a Question

Usually answered in minutes!

Top Poulan Garden Experts

Doctor PC

Level 3 Expert

7733 Answers

Roland W VanLue

Level 3 Expert

486 Answers

Phil Walker

Level 3 Expert

605 Answers

Are you a Poulan Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Have a manual for Poulan Pro Lawn Tractor 2006 and Newer Ground Drive Mower Belt? Or just drag it here!

6ya staff · Answer 1 · 1/2/2017 12:00:00 AM

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

shane shubert · Answer 2 · 8/11/2009 12:00:00 AM

On the trimmers when torqing head bolts down,I dont bother looking for torque specs (theres some people that will shoot me for saying this). I just snug them up and then give each one a one quarter turn tighten up. Its always worked for me.

Doctor PC · Answer 3 · 11/20/2010 12:00:00 AM

Doctor PC

7733 Answers

SOURCE: I had to put the 38cc engine into a new case and

Just tight enough as you feel it is .Theirs no torque specification.

If you need more help come back.Post / thumbs / testimonial are welcome!

Posted on Nov 20, 2010

Jim flowers · Answer 4 · 11/11/2016 12:00:00 AM

Jim flowers

821 Answers

SOURCE: why engine surges on poulan pro lawn mower 450e,961120130 mod.pr450n20s

usually has to do with the fuel system. (dirty carburetor). take the bowl off and see if there is water or dirt in there if so take off and apart and clean real good.

Posted on Nov 11, 2016

Kohler lawn mower engine, mod SV#6005, spec # SV 600-0003, ft lb of torque for head bolt, valvue lash.

4 Suggested Answers

6ya staff

shane shubert

Doctor PC

Jim flowers

Add Your Answer

Attachments: Added items

Related Questions:

Toyota 2c. I need cylinder head and flywheel Torque settings

Looking for cylinder head and connecting rod torque specs for a Kohler K582 engine

Need torque spec for head bolts on engine 10L902-0536-E2

NEED TORQUE SETTINGS FOR 18 HP MODEL 31H777-0297-E1. ROD BOLTS AND HEAD BOLTS. IS THERE A PATTERN TO TIGHTENING HEAD BOLDS

We were wondering the torque on the head bolts on a Kohler motor for a lawn mower.

Torque spec

I have 4.9L6 need torque specs for cylinder head

Cylinder head torque specs

Head bolt torque specs needed for 96 tbird 3.8

Torque specs for the cylinder head

Not finding what you are looking for?

Pro Lawn Tractor 2006 and Newer Ground Drive Mower Belt

Toyota 2c. I need cylinder head and flywheel Torque settings

Open Questions:

bent pushrods on 20hp v twin briggs lawn trator

replacing a carburetor on a lawn tractor

replace the Arm Assembly Pad Break part # 131845x900 on poulan lawn tractor mower deck

pxt 12530 manual looking for manual for poulan xt lawn tractor model pxt 12530

Related Topics:

Ask a Question

Top Poulan Garden Experts

Doctor PC

Roland W VanLue

Phil Walker

Are you a Poulan Garden Expert? Answer questions, earn points and help others

Manuals & User Guides

Kohler lawn mower engine, mod SV#6005, spec # SV 600-0003, ft lb of torque for head bolt, valvue lash.

4 Suggested Answers

6ya staff

shane shubert

Doctor PC

Jim flowers

Add Your Answer

Attachments: Added items

Related Questions:

Toyota 2c. I need cylinder head and flywheel Torque settings

Looking for cylinder head and connecting rod torque specs for a Kohler K582 engine

Need torque spec for head bolts on engine 10L902-0536-E2

NEED TORQUE SETTINGS FOR 18 HP MODEL 31H777-0297-E1. ROD BOLTS AND HEAD BOLTS. IS THERE A PATTERN TO TIGHTENING HEAD BOLDS

We were wondering the torque on the head bolts on a Kohler motor for a lawn mower.

Torque spec

I have 4.9L6 need torque specs for cylinder head

Cylinder head torque specs

Head bolt torque specs needed for 96 tbird 3.8

Torque specs for the cylinder head

Not finding what you are looking for?

Pro Lawn Tractor 2006 and Newer Ground Drive Mower Belt

Toyota 2c. I need cylinder head and flywheel Torque settings

Open Questions:

bent pushrods on 20hp v twin briggs lawn trator

replacing a carburetor on a lawn tractor

replace the Arm Assembly Pad Break part # 131845x900 on poulan lawn tractor mower deck

pxt 12530 manual looking for manual for poulan xt lawn tractor model pxt 12530

Related Topics

Related Topics:

Ask a Question

Popular Questions

Poulan leaf blower won't start

Need diagram for fuel lines on craftsman chainsaw

Poulan Pro 200 Leaf Blower won't start. I have

Diagram fuel lines tank primer carbutor poulan pro

Gas line diagram for poulan 2050 2.0 CI '97

Top Poulan Garden Experts

Doctor PC

Roland W VanLue

Phil Walker

Are you a Poulan Garden Expert? Answer questions, earn points and help others

Manuals & User Guides