My husband has Netgear in our house but i need an IP address for my lap top and Ipod, can you help me with that?

You have to change the ipddress on the router different then the modem. For example 192.168.9.1 and leave the modems ip alone. Plug the cable into the Lan port of the router. Go to the setup screen on the router and tell give your username and password that
Comcast gives you. You will need comcast gateway address and dns numbers. There will be a connect button on the router and tell it connect it to the modem. You are trying to let the router receive that only ip address.

It is hard to say without the netgear model and version, yet the concept is the same, open your web browser, type the ip address of the netgear in the address bar (you will need a password), then look for a menu regarding wireless or wlan or advance wireless configuration, and there you will see an option about channel selecction, just change it to match your laptop channel.

good luck.

1.) Check if you put static ip on your NIC. If not, then you are DHCP.

2.) Do some Command Line Interface at CMD.

a.) Start > Run > CMD
b.) ipconfig /all
d.) Try to release the ip by typing this command: ipconfig /release
c.) Then, renew : ipconfig /renew

try to flush your dns, by typing these:

ipconfig /flushdns

and register again your dns by typing these:

ipconfig /registerdns

If this solution does not correct your problem, try to reset your Netgear, by the way, do you put WPA on your wireless network?

Hit me back..

TRY REPAIRING THE CONNECTION AND MAKE SURE THE SSID CODE IS CORRECT

Check the security settings and see if MAC Address filtering is on in the router.

1. check your wireless adapter TCP/IP settings if its set into "Obtain as IP address Automatically".
2. if the settings is set as Automatic and your not getting IP address then select "Use the following IP Address"
3. use IP address followed to your router address like if192.168.0.1 in router type 192.168.0.2 or192.168.0.3 just check the next address IP in your network.
4. after typing subnet IP will automatically set
5. type the router IP address as your default gateway
6. click OK to save your new settings

Hope this will help

try to customize your wireless settings. change the wireless name/ssid to something else and change the wireless channel as well. verify also if there's a wireless security enabled, if it has you need to use the correct wireless security/network key when connecting your laptop wirelessly. you can go to the router's setup page to verify your wireless settings by typing the ip address of your router to the address bar of your web browser, http://192.168.1.1 (note: by default the ip address of the router is 192.168.1.1 unless you have changed it to something else. the default username is "admin" and the default password is "password")

hope this'll help you

ciao!

If you don't have the wireless password for your wireless connection. The thing to do is log into the Router's webpage via the Router's IP address. From there you can go to the wireless section and in most routers this section shows the wireless password.

If you have trouble getting on to the Router's webpage. Just comment back on this and I can probably step you through it.

1. Click Start, Run, CMD, hit enter and write down the ip address of your default gateway.

2. Open your web browser, in the address bar type http://(ip of default gateway).

3. Type 'admin' for both username and password. If this doesn't work try using admin for just the password.

4. Go to wireless settings and first make sure that the SSID broadcast is enabled, if not enable it. Second, go to the wireless security section and choose an encryption method, i recommend wpa personal. Use a passcode that is easy for you to remember, you will need to enter it before you can access the internet wirelessly.

The Automatic Private IP Addressing (APIPA) protocol
automatically assigns an IP address from the range:
169.254.1.0 to 169.254.254.255. If the APIPA protocol is
disabled, the default IP address of a Brother print server is
192.0.0.192. To change it, use the printer control panel (if
applicable), the BRAdmin Professional, Web BRAdmin software
or let your DHCP server allocate an IP address to the printer.
2 Refer to chapter 10 of this User’s Guide to learn how to
configure the IP address on your printer.
3 The default password for Brother print servers is access.
4 Windows® 2000/XP users can print using TCP/IP using the
standard Network Printing software and IPP protocol software
built into any Windows® 2000/XP installation.if you need manual just email me at repagenserv@saipan.com or romeo_palencia@hotmail.com