Question about Dishwashers

1 Answer

Dishwasher not filling w/ water hot point - Dishwashers

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Dishwashers Master
  • 43,501 Answers

Hi,
Here is a tip the will elaborate on your problem more, but the bottom line is that you need to replace that fill valve...

Dishwasherdishwasher not filling w/ water - 2_bing.gif Trouble No Water entering Dishwasher2_bing.gif
http://www.fixya.com/support/r4021363-dishwasher_trouble_no_water_entering

heatman101

Posted on May 28, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My Hot Point Dishwasher is leaking water. It was


Hi


Check for any kind of leaks around lower spray arm or soap door. Replace the arm if any cracks are found. Also make sure that door latches firmly, and the gasket is not cut.
The leak can also happen due to a broken fill valve. To check, take off the access panel from the front of the dishwasher so you can reach the fill valve attached to the metal bracket. Use a multimeter to check the continuity across the two black terminals at the top of the fill valve. If it reads 120 V, replace the fill valve. Make sure the thin filter screen between the bracket and fill valve is not blocked by debris.


Please post back for any further assistance.

Daniel

Jul 23, 2010 | Hotpoint 24 in. HDA3400G Built-in...

1 Answer

Dishwasher fills with water, then empties, fills then empties, and repeats this cycle a few times - then decides to work. then part way through cycle - it repeats this frustrating cycle, making the whole...


Hi, Your dishwasher may pre-heat the water. If so, and if the water entering the dishwasher is cool, the heater may take up to half an hour to heat the water. To avoid the wait, increase the incoming water temperature before turning on the dishwasher. Do that by running the kitchen sink faucet until the water runs hot. Or increase the temperature of the hot water to the entire house at the hot water heater.
Timers don't often fail. But if every other part of the dishwasher seems to be working properly and the timer knob seems to be stuck in one place--doing one function continuously--the timer may be at fault. Dishwasher timers can't be repaired. If yours is defective, replace it.

Apr 18, 2010 | Fisher and Paykel DS605I Built-in...

1 Answer

My dishwasher is not heating the water up just running cold


Try turning on the faucet by the dishwasher and let the water run until it gets hot. Once this is done turn on the dishwasher and see if the water is warm or hot. Most dishwashers do not heat the water (residential dishwasher) they take the hot water from the hot water side of the sink. If the water heater is located a distance from the dishwasher then the cold water fills the dishwasher before the hot water can make it to the unit. This should cure your problem.

Hope this helped

Dave

Jan 15, 2010 | Dishwashers

1 Answer

No water comes in my kitchenAid dishwasher


you only need prime to pump water out if you are not getting water to D/W it is most likely the water control valve

Oct 23, 2009 | Dishwashers

1 Answer

Water won't drain from my hot point dishwasher


Your drain/waste line under the sink is clogged with grease and soap scum.
Remove the P-trap and connecting drain lines, route out the drain and lines.
If you have a air gap mounted on the sink, clean that too.

Apr 02, 2009 | Hotpoint 24 in. HDA3740G Stainless Steel...

1 Answer

Noritz tankless water heater/dishwasher not hot enough to clean


You are doing everything you can. Your dishwasher probably isn't drawing enough hot water to activate the unit so opening the faucet and flowing more water will activate the unit. Just try to adjust the flow from the faucet to a point it, plus the draw from the dishwasher, will activate the unit. This will come with trial and error as I am sure you have already experienced. Also, open the dishwasher when it does get filled and check the water temperature. You might have the unit set at a low discharge temperature. Do you have a touchpad to control the water temperature adjustment?

Feb 17, 2009 | Noritz 7.1 Gpm Natural Ng Gas Tankless Hot...

2 Answers

Water fills up dishwasher after complete maybe a day or two later


Sound like the hot water sonenoid is stuck in the open position. Locate this solenoid and tap it lightly with a small hammer while the hot water is open. If it does not stop it will beneficial to have this part replaced. I hope this will help.

Jan 17, 2009 | Kenmore 24 in. 15932 Built-in Dishwasher

1 Answer

My dishwasher is filling up with water but the water want get hot


The water needs to be hot before it goes into the dishwasher. Just before you start the machine, run the hot water faucet until the water gets hot.

Some dishwashers have a heat boost feature to sanitize the dishes, but it's not intended to take cold input water and make it hot.

Nov 12, 2008 | Dishwashers

1 Answer

Diswasher wont fill


Faulty fill valve?
Timeing out with insufficient flow of water?
Hot water to hot and locking up valve?

Apr 13, 2008 | Bosch 24 in. SHU43 Built-in Dishwasher

1 Answer

Hot point dishwasher


your always gone hav a small oamount of water in machine after cycle is complete never can totally remove all water. not to worry though before running next cyclye the dishwasher first redrains and then fills

Mar 02, 2008 | Dishwashers

Not finding what you are looking for?
Dishwashers Logo

Related Topics:

112 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dishwashers Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Owen Barnes

Level 3 Expert

867 Answers

Brad Brown

Level 3 Expert

15441 Answers

Are you a Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...