Question about Epic View 550 Treadmill

1 Answer

My fans don't turn on when I press the button. Has anyone else had this problem?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Epic Master
  • 832 Answers

This problem occurs even in the $7,000.00 units. My suggestion is unplug the treadmill then remove the upper console. Remove the back panel find the two wire that come form the fan motor get a 9v battery plug it into the motor and see if it runs. If it does, then you have a function pad problem or upper electronics problem ( I tend to lean towards the function pad ) if it doesn't then replace fan motor

Posted on Jun 01, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

GE Microwave VM240 AV underchassis fan & light don't work


It is more than likely there are one or two defective door switches that need to be replaced.

May 07, 2012 | Microwave Ovens

1 Answer

Monte Carlo ceiling fan and light not working


Even a brief power outage can cause amnesia in the receiver. You can try disconnecting power at the source and spending a few minutes removing the battery from the wall-mounted remote and pressing all buttons to eliminate the 'stuck button' problem. Reinstall the remote battery and reconnect main power to the unit. Test operation.
Lastly, there always is the possibility that some gremlin changed your original control setup.

Jun 23, 2017 | Dryers

1 Answer

Error 5200 or PO8?


1. Turn Off printer, cable power still plug in.

2. Press Stop/Reset button, don't release the button.

3. Press Power button by holding without release and than release Stop/Reset Button.

4. Press Stop/Reset button two times (2x) now release the Power Button.

5. Wait until service mode to zero (0).

6. Turn off the Printer, cable power still plug in.

7. Press Stop/Reset button, don't release it.

8. Press Power button don't release & than release Stop/Release button.

9. Press Stop/Reset button four times (4x), wait until service mode to "1"

10. Turn off printer, and loose cable power, wait for one (1) minute.

11. Connect cable power, turn on printer again, now this printer ready to use.

Aug 12, 2011 | Canon Pixma Mp250 Allinone Inkjet Photo...

1 Answer

Printer shows alarm with p and 8 flashing


Follow this instruction step by step.

1. Turn Off printer, cable power still plug in.

2. Press Stop/Reset button, don't release the button.

3. Press Power button by holding without release and than release Stop/Reset Button.

4. Press Stop/Reset button two times (2x) now release the Power Button.

5. Wait until service mode to zero (0).

6. Turn off the Printer, cable power still plug in.

7. Press Stop/Reset button, don't release it.

8. Press Power button don't release & than release Stop/Release button.

9. Press Stop/Reset button four times (4x), wait until service mode to "1"

10. Turn off printer, and loose cable power, wait for one (1) minute.

11. Connect cable power, turn on printer again, now this printer ready to use.

Aug 06, 2011 | Canon Pixma Mp250 Allinone Inkjet Photo...

3 Answers

My mp250 printer shows error p08, I can't use it in any way. I replaced the black ink tank with a new one and tried resetting the printer and it doesn't solve the problem.


Follow the instructions step by step

  1. Turn off printer, cable power still plug in,
  2. Press Stop/Reset button don't release
  3. Press Power Button don't release and than release Stop/Reset button
  4. Press Stop/Reset button 2X , wait until service mode to " 0 "
  5. Turn off printer, cable power still plug in
  6. Press Stop/Reset button don't release
  7. Press Power Button don't release and than release Stop/Reset button
  8. Press Stop/Reset button 4X , wait until service mode to " 1 "
  9. Turn off printer, and loose cable power, wait one minute.
  10. Connect cable power, turn on printer again, now this printer ready to use.

Jul 06, 2011 | Canon Pixma Mp250 Allinone Inkjet Photo...

1 Answer

I don't have the instructions and I am looking for an online instructions manual on how to install this fan.


* I don't have the instructions
* Problem with the Vacuums
* I don't have the instructions and I am looking for an online instructions manual on how to install this fan

faxmando_0.gif

I guess you pressed SEND before you could say what it is, the brand name, and the model.

Can you give it another try?

It would be very nice to know if anyone can help.

Jun 27, 2011 | Vacuums

1 Answer

Where i can run cooling fan on hp pavilion dv6 laptop 2011 ? i buy new one but i don't no which button i have to press Please help me


It sounds like your cooling fan has stopped and you bought a new one.
The fans are plugged into the motherboard. Your motherboard probably has at least two fan connectors-they are marked "fan" or "case fan" or something like that. There is no button to turn them on. They come on when you start the system.

Jun 03, 2011 | Computers & Internet

1 Answer

Canon error p08 Problem


Follow the instructions step by step

1. Turn off printer, cable power still plug in,
2. Press Stop/Reset button don't release
3. Press Power Button don't release and than release Stop/Reset button
4. Press Stop/Reset button 2X , wait until service mode to " 0 "
5. Turn off printer, cable power still plug in
6. Press Stop/Reset button don't release
7. Press Power Button don't release and than release Stop/Reset button
8. Press Stop/Reset button 4X , wait until service mode to " 1 "
9. Turn off printer, and loose cable power, wait one minute.
10. Connect cable power, turn on printer again, now this printer ready to use.

If you are satisfied, please rate or/and leave a testimonial. Thanks!

May 10, 2011 | Computers & Internet

1 Answer

Intell-Touch instructions for casablanca fan/light


Light Operation: With the light in the off position press and hold the light button (do not let go). The lights should start at a dim setting and gradually get brighter and brighter. When they get to a setting you desire let go of the light button. To reduce the brightness of the light you must first turn the light off, and then press the light button and hold it in as described above. If the light is off, and you press the light button quickly to turn it on, the light will go back to the previous setting. So if you last had the light on the high setting, it will go back to the high setting, if you had the light at a lower setting it will turn back on to the lower setting. Keep in mind you can increase the light intensity at any time by pressing and holding the light button, but to decrease the light intensity, you must first turn the light off, and start over by pressing and holding in the light button.
Fan Operation: With the fan in the off position, press and hold the fan button (do not let go). The fan should start at a slower speed and get faster and faster. When the fan is at the speed you desire, let go of the fan button. To slow down the fan speed you must first turn the fan speeds off by pressing and releasing the fan button. If the fan speeds are off, and you press the fan button quickly to turn it on, the fan will go back to the previous setting. So if you last had the fan at the highest setting, it will go back to the high setting, if you had the fan at a lower setting it will turn back on to the lower setting. Keep in mind you can increase the fan speed at any time by pressing and holding the fan button, but to decrease the fan speed you must first turn the fan off, and start over by pressing and holding in the fan button.

Jul 20, 2010 | Casablanca Fan (3232A) Ceiling

1 Answer

Internal fan won't turn off in 97 chrysler LHS?


Is your climate control center working, can you manuelly turn the fan control to its lowest speed. If you press and hold the off button below the auto button that should turn off the fan

Apr 27, 2009 | 1997 Chrysler LHS

Not finding what you are looking for?
Epic View 550 Treadmill Logo

Related Topics:

106 people viewed this question

Ask a Question

Usually answered in minutes!

Top Epic Exercise & Fitness Experts

Ross Metcalfe
Ross Metcalfe

Level 2 Expert

128 Answers

Matt Olenzek
Matt Olenzek

Level 2 Expert

297 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

6694 Answers

Are you an Epic Exercise and Fitnes Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...