Question about PDAs

1 Answer

I need a dc power card for a wdxb1600jbrnn - PDAs

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Hello
my phone i have problem if you on some mins there we
off ............

Posted on Nov 01, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My pocket pc e310 wont turn on. i only have the cradle and no ac charger. i have unplugged the battery for a reset but nothing happens after i plug it back in. when plugged in to the cradle, there are no...


The e310 can't use USB power to charge through the cradle. (It needs more than USB specs allow.) You have to supply +5v DC to the connector at the cradle or the e310 itself. Positive terminal is the center pin/hole, negative terminal is the outside barrel of the plug.

Jun 02, 2011 | Toshiba e310 Pocket PC

1 Answer

Cannot power on the phone (z610)


Check power adapter’s DC plug that connects into the laptop power socket with a multi-meter, the voltage should be slightly higher than the voltage that is printed on the label on the bottom of the adapter. If the voltage is zero or way below the voltage that is printed on the label then the power adapter is faulty and needs to be replaced.

Nov 26, 2009 | Sony Ericsson Z610i Luster Black Phone

1 Answer

My T-Mobile MDA won't turn on or take a charge, battery was low


I had the same problem, but got the idea to "jump start" the battery from Googling the problem. At night, I had turned off my MDA to charge the battery and then in the morning, couldn't revive it. I removed the battery from my MDA, and determined which battery terminal was positive (far end of one side) and negative (far end of the other side) by using a multi-meter. BTW: Battery was still @ 3.5V (okay…battery was still alive, if just barely). Then, I found a 5V DC charger (5W Max output = ~1A) from my bluetooth headset. I used one wire (CAT5E) and connected it to the negative side of the adapter (outer sleeve - again, verified by multi-meter) and another wire to connect to the positive tip of the adapter. I had to strip about 1/2-inch of the insulation off of the wire on the DC adapter side, and about 1/8-inch of the wire on the battery side. Plugged in the 5V DC charger and then I touched the negative wire to the negative battery terminal and held it there, while I touched the positive wire to the positive battery terminal for about 30-45 seconds. Put the battery back in the MDA, started it up, and now it's charging on the regular MDA AC Charger that came with the phone. Problem solved.

Apr 07, 2009 | T-Mobile MDA

1 Answer

I want owner manual for DC/AC ivverter 512


how do you put in the sim card?

Nov 29, 2008 | PDAs

1 Answer

Power Supply


Hi

It is usually 5V DC but it may vary depending on the country in which you bought the pocket pc. You can have a look on the back of your pocket pc and confirm that the input is 5V DC.

Have a nice day and please remember to rate this solution as FixYa if it helps you.

Jul 28, 2008 | HP iPAQ H3630 Pocket PC

1 Answer

Can't use my pocket pc as a mobile phone


Hello Ric777, I would suspect the mainboard of your pda at first. But for the begining you should try to clean the contacts of your sim slot and check to see if all of them connect properly to the sim card. If all of them do connect properly, my second gues would be that the pda doesn't power on the sim card. Like memory cards sim's need to be powered first in order to work. Most pda that have this problem fail to initialise a sim because they can't suply the 3.3 or 2.7 volts needed due to a hardware mailfunction. However this test should be runned by a service center, they will have to dissasemble your pda in order to check these. In your case, you can make a hard reset and check the sim card pins in the pda. If this doesn't help, you will need service assistance. I'm sorry for not being able to help further. Good luck.

Apr 23, 2007 | i-mate Pocket PC

1 Answer

Methods of extending the battery time


Decrease the Front Light brightness while the MobilePro P300 is on battery power. To do so, tap Start --> Programs --> My Settings and tap the Front Light icon. Click the "DC" tab and decrease the brightness level to the desired level.

Sep 15, 2005 | NEC MobilePro P300 Pocket PC

Not finding what you are looking for?
PDAs Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top PDAs Experts

k24674

Level 3 Expert

7987 Answers

kakima

Level 3 Expert

96417 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a PDA Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...