Question about Hotpoint 24 in. FDW60 Free-standing Dishwasher

1 Answer

Hotpoint fdw60 dishwasher

My dishwasher appears to be running its normal cycle until right at the end the light switches over to delicate and upon opening i find the water has not got warm. Done a test on heater element and it seems fine

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 868 Answers

This is a bad control board that if replaced will only repeat in a short time .My advice is to contact the manufacturer and complain,you have the right as a consumer to do so.

Posted on May 23, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Dishwasher not finishing cycle


A10 4 + 6 Heating circuit Heating element, connections, module,
relay, pressure switch

A10 Open circuit in heating circuit.
• Check the circuit of the heating element (26 ohms).
• Check for an open circuit heater cut-out.
• Check pressure switch open circuit (connections 11-14).
• Check wiring and connections between module card, pressure switch and heater.
• If all above is OK, replace module card.

Sep 18, 2014 | Hotpoint 24 in. FDW60 Free-standing...

1 Answer

Hotpoint Aquarius FDW60 Machine stops halfway through its cycle & the "fast" & "delicate" cycle LED's are flashing - what is my problem?


This sounds like the heater is not energising usually means the heater has failedalthough a blocked or sticking pressure switch will cause the same problem

Apr 14, 2010 | Hotpoint 24 in. FDW60 Free-standing...

1 Answer

Hotpoint dishwasher


Switch the machine off and unplug at the mains. Leave for ten minutes, then plug in and switch on. My dishwasher control panel had a mind of its own and did what it wanted including leaving water in the bottom of the machine. The electrics sometimes need re-booting! Hotpoint suggested the solution and it worked for me. Saved me £99 call out charge. Good luck.

Jun 04, 2009 | Hotpoint 24 in. FDW60 Free-standing...

2 Answers

FDW60


I have exactly the same problem, please let me know if you find a solution and I will do the same.

Sep 21, 2008 | Hotpoint 24 in. FDW60 Free-standing...

1 Answer

Fast and delicate lights flashing.


No, do not repair this, everyone who has purchased this model should demand a refund !!!!The problems are endless.

Apr 24, 2008 | Hotpoint 24 in. FDW60 Free-standing...

1 Answer

HOTPOINT DISHWASHER FDW60


Hi,

I have just had my dishwasher fixed by Hotpoint, as the heater was working and the dishwasher only stopped with the fast and delicate lights just before the drying process he replaced the main control board. This has solved the problem, I suspected the fault to be the thermistor as the heater seemed to be getting to hot but I had no idea where it was.

It turns out the thermistor is attached to the main control board and hangs down behind the front door that gives just a rough temperature level for the main control board.

As it's soldered directly onto the control board I would suggest replacing the whole control pcb for anyone with this fault unless you can find any spec details for the thermistor.

Mar 18, 2008 | Hotpoint 24 in. FDW60 Free-standing...

1 Answer

FDW60 Fast and Delicate Lights Flash


This is a bad control board that if replaced will only repeat in a short time .My advice is to contact the manufacturer and complain,you have the right as a consumer to do so.

Mar 17, 2008 | Hotpoint 24 in. FDW60 Free-standing...

1 Answer

FDW60 Fast and Eco Lights


This is a bad control board that if replaced will only repeat in a short time .My advice is to contact the manufacturer and complain,you have the right as a consumer to do so.

Mar 17, 2008 | Hotpoint 24 in. FDW60 Free-standing...

Not finding what you are looking for?
Hotpoint 24 in. FDW60 Free-standing Dishwasher Logo

Related Topics:

194 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hotpoint Dishwashers Experts

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

bosch5

Level 2 Expert

157 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Hotpoint Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...