Question about Garden

1 Answer

Can't start craftsman lawnmower (weedeater model) which was just serviced and bought at garage sale

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 404 Answers

Make sure the safety lever disengages the safety switch fully, if there is no spark that could be the reason and may be remedied by an adjustment, the other issue could be the shear key on the crankshaft is distorted and the timing is off a bit, again you will have no spark at all if this happens.

Posted on May 27, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have bought a second remote control craftsman 315 918191 i have remote device install with my crafftsman door opener there is no learn buttom on either device what can i do thank you


Post the model number of your opener. It is on the end of the motor unit nearest the door. It starts with 139. Also post the model number of your new remote. It should also start with 139.

Mar 12, 2011 | Sears Craftsman LiftMaster Chamberlain...

1 Answer

When I try to start my Craftsman Model # 917.388861 lawnmower, it will start and then dies right away, then Iit would start unless I prime it. Before it started doing this, the lawnmower was running very...


Sounds like you will need to clean your carburetor.
Be sure to use compressed air to blow out all the fuel and air passages.
Sometimes you can get by with priming the carburetor a few times, and letting it run a few times like that and it will flush the gunk out of the jets,but most of the time you will need to rebuild the carburetor.
If the mower/weedeater is over a couple years old, then I also recommend that you buy and install a new carburetor repair kit,because the diaphragm will get hard and that will cause it to be hard to crank.
When you clean your carburetor and remove the jet screws, You will first seat the jet screws and count the number of turns it takes to seat the jets from their original position.
That way when you go to put the jets back in, you know how many turns they were in/out.
Please rate me,
Thanks
Good Luck,
I hope this helped

Aug 16, 2010 | Craftsman 675 Series 190cc 22" Briggs ...

1 Answer

Engine turns once and lawnmower won't start; even


ook at the contacts on the key swith mabee fryed it with the charger? or the lead to the silinoid could be badd

Jul 20, 2010 | Sears Craftsman LiftMaster Chamberlain...

1 Answer

Weedeater gas edger won't start!!!!!!!!!


yes, there is a spark module, but it's highly unlikely that two would have a bad module - more than likely, it is your gas mix. it must be fresh for the engine to run. the gas we have today will go bad in about a month and a half. if you happen to live in an area that has E85, forget it. small engines will not run very long, if at all on this junk. in some areas, you can get gas without alcohol, but it can only be used for lawn & garden equipment. it's expensive, but your engines will run

Sep 20, 2009 | Craftsman 25cc Gas Line Trimmer

1 Answer

Tempory password


Find the smart/learn button on the rear of the motor unit just to the left of all those white wires. Press and immediately release this and then walk over to your keypad and key in any 4 digit PIN you like and press enter.

Sep 19, 2009 | Sears Craftsman LiftMaster Chamberlain...

1 Answer

Bought a 14' Weedeater at a garage sale - like new.


Please go here to download a .pdf manual for your #900-74528 trimmer.

I hope this information allows you to resolve this issue. If you need further assistance, please post back with a comment to this thread.
If I've managed to answer your question or solve a problem, please take just a moment to rate this post....thanks!

Aug 29, 2009 | Garden

1 Answer

Don't know how to advance cutting wire.


Did you try bumping the head on the ground? Also, the head could be dirty, keeping the string from feeding. Or maybe the previous owner tried putting a larger size string in the head. Check to see what the proper size is for your trimmer.
Both of these suggestions could cause this.

Jim

Jun 03, 2009 | Craftsman Garden

2 Answers

Missing parts for guard assembly craftsman table saw 133.299315


You will have to start searching craigslist and amazon, estate sales, garage sales etc.

Nov 24, 2008 | Craftsman Saws

Not finding what you are looking for?
Garden Logo

Related Topics:

73 people viewed this question

Ask a Question

Usually answered in minutes!

Top Garden Experts

Dennis Key
Dennis Key

Level 3 Expert

2478 Answers

john h

Level 3 Expert

12173 Answers

yadayada
yadayada

Level 3 Expert

76164 Answers

Are you a Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...