Question about Astatic 636L Noise Canceling Microphone Microphone

1 Answer

Teardrop - icom 706mkII

Can someone help me with the wiring please,dont want to muck it up.

Posted by on

  • robbo h Apr 14, 2008

    im trying to wire up my astatic teardrop to my 706 mkll ive got the mike exstention that came with the 706 but it has no plug on the end can somebody help me with this simple task

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

Http://homepage.ntlworld.com/rg4wpw/astaticbook.pdf

Posted on Jun 16, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Heil icm plug wiring diagram


The Heil "ICM" microphone is designed to be used with certain Icom brand ham radios. These have a 8-pin round plug. Describing the pinout to you will depend upon your perspective, whether you are looking at it from the microphone plug itself, or the microphone socket on the front of the radio. Therefore, from the perspective of looking at the mic plug on the end of the mic cable, note that there is a notch or dimple in the plug that also lines up with the screw. Going clockwise from the notch, the pins are numbered 1 thru 7. Pin #8 is the center pin.
Pin 1 = mic input
Pin 5 = Push-to-talk (PTT)
Pin 6 = PTT ground
Pin 7= Mic ground

From the standpoint of an Icom transceiver, the remainder of the mic connector pins are as follows:
pin 2 = +8 volts DC (output from the radio)
pin 3 = frequency control up/down
pin 4 = squelch switch
pin 8 = audio output (level varies w/vol control)
Hope this helps

Jan 03, 2014 | Heil Sound Audio Players & Recorders

1 Answer

I bought a new logic unit (front face) of Icom F121 and it needs to be restored. How do you restore a logic unit for the Icom F121?


1- You have to to "Reserve" mode.2- Change Set Mode Access: Inhibit to Enable3- Common>>Secutity Change Set Mode Access : Inhibit to Enable4- Enter RX TX frequency and write to the radio.
or you can download version Rev 1.7 from here:
http://www.two-way-radio-tools.com/icom-softwares.html
http://www.two-way-radio-tools.com/icom-radio.html

Aug 27, 2010 | ICOM Informatique IC-F121 VHF 136-174MHz...

1 Answer

When using the OPC617 external cable, what solder pads need jumpered for PTT and mic audio?


To use OPC-617 option cable:1- open your CS-F100 Rev 1.7, read your radio.2- click on Common >> Expert >>EPTT/FTSW change to EPTT, 3- On the main board , look into the left side of the board you see pad D, solder ittogether, if you use pad F, you shou.ld put a 47K ohm resistor.You can follow this link for your pin out connection.http://www.two-way-radio-tools.com/icom-mc1700-mdc.html
and download ver sion Rev 1.7 from herehttp://www.two-way-radio-tools.com/icom-softwares.html
HP

Jun 04, 2010 | ICOM Informatique IC-F121 VHF 136-174MHz...

1 Answer

How do I reset the F221 to factory settings. I cloned the unit with V1.6 of the programming software with updates that included turning on the user start password and now the box will not communicate with...


F121 VHF, F221 UHF they both use the latest Version 1.7.
For F121 Factory default as follows:Open your CS-F100 software, enter RX TX frequency below, and write to the radio.Ch1: 136.100 MHzCh2: 155.100 MHzCh3: 173.900 MHz
For F221 Enter RX TX frequency belowCh1: 440.000MHzCh2: 460.000MHzCh3: 489.000MHz, then write to your radio
Or you check from this site:http://www.two-way-radio-tools.com/icom.html
HP

Feb 04, 2010 | ICOM Informatique IC-F121 VHF 136-174MHz...

1 Answer

ED 8000


You need to replaced the "voice coil". that thing that youve been desoldering and soldering is the voice coil. It has two wires- white and black. it is already grounded and need to be replace (the fact that it humms..). my company distribute wow magic sing here in Philippines and we can easily repair that.

Dec 25, 2008 | Magic (ED8000) Professional Microphone

Not finding what you are looking for?
Astatic 636L Noise Canceling Microphone Microphone Logo

Related Topics:

153 people viewed this question

Ask a Question

Usually answered in minutes!

Top Astatic Audio Players & Recorders Experts

kakima

Level 3 Expert

100304 Answers

 Grubhead
Grubhead

Level 3 Expert

4706 Answers

The Knight
The Knight

Level 3 Expert

71070 Answers

Are you an Astatic Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...