Question about Buffalo Tools COCD24 24 Volt Cordless Hammer Drill

1 Answer

Can't release drill bit from Buffalo cordless drill

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 145 Answers

If the chuck is too tight to get the bit out you can either put a glove on one hand grab the chuck and run the drill in the reverse direction or if that will not work use vise grips or a small pipe wrench on the chuck to loosen it but be sure to tape the pipe wrench or vise grips with a thin piece of duct tape so you don't gouge the drill chuck.

Posted on May 26, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i insert bit in cordless dewalt keyless hex chuck?


It only accepts 1/4" hex shank bits and nut drivers. Mine just pops in and to release it, you push the black collar around the bit down. Cannot put round end bits in it. Only hex shanks

Oct 26, 2013 | Dewalt DW056 18 Volt Cordless Impact...

2 Answers

I have a Hitachi WH 18 DFL cordless impact driver, which I love. I was doing a little bit of heavy drilling, and now the drill bit is stuck. The sleeve extends as if to release the bit, but the bit do


My guess is that the bit twisted a little in the bit holder so the steel ball is bound. If the collar moves you could try a slide puller on the bit and see if you can impact it out with the slide puller. Or you could take the bit holder apart. There is a retaining ring that holds it all together right on top. Pull that off and a washer, spring and the collar will come off. Becarefull to watch for the steel balls on the spindle. They WILL fall out! Now hopefully the bit will come out. If not it may need to be twisted in the oposite direction that it got stuck when you were using it to break it free. Hope that helps and good luck!

Jan 19, 2012 | Dewalt 18 Volt Compact Drill Kit

1 Answer

I have drilled a 1 inch hole in my concrete basement wall. I cannot release the bit from the drill. The chuck won't turn by hand to release the bit.


Good Afternoon, Ladooudep55:

I hope you have got your bit back, but if not, remount the drill chuch onto the bit, and drill in forward without pushing the bit. If it still won't move, You can gently wobble the drill to enlarge the hole and retrieve the bit.

The other method is alternating light hammer taps with compressed air. It will make lots of grit dust.

If the hole around the bit is wet, you may have drilled into an iron pipe, if it smells it was the sewer drain. You will have to decide if you want to replace the pipe section or run an epoxy patch once you have retrieved the bit.

Chr

May 01, 2011 | Makita BDF452HW 18V Cordless Lxt Lithium...

1 Answer

How do I remove a stuck bit from the chuck?


put the drill in a vice. then use the chuck key  and a hammer to release the bit.
 if necessary use wd40 spray to free up chuck.

Jan 24, 2010 | Black & Decker 18V Cordless Drill/Driver

1 Answer

Describe how to remove drill bit and install a


Most cordless drills use keyless chucks these days. Shift the drill into reverse and hold the main body of the chuck. Pull the trigger and the bit should come out. Put it into forward and run it to tighten onto a new bit.

Dec 02, 2009 | Drills

1 Answer

Jammed short shank drill bit in ring grabber drill driver


Mix a little JB weld stick anything to head of stuck bit. let harden and pull the sucker out.

May 16, 2017 | Makita Tools 18V 1/2" Lxt Lithium - Ion...

1 Answer

I can't loosen the part where the drill bit goes in. It's stuck!


Try using a large wrench to turn the chuck. It may loosen enough to release the bit

Apr 18, 2009 | Black & Decker 18 Volt Cordless Drill...

1 Answer

Chuck will not release bit


Hi,

the Chuck should be 2 Part.

Use 2 pair of stillsons Or pipe wrenches, Tight On the 2 Chuck Parts, Crack in opposite Directions.

Alternative, Use Wrench On Chuck Jaw, Short sharp Blow With Hammer.

Mike @ compurepair.


Feb 28, 2008 | Dewalt DC920KA Heavy Duty Xrp 18V Cordless...

2 Answers

Makita 6222D hole drill bit is stuck


When this happened to me I held the shaft of the drill bit tightly with my hand and reversed the direction of drive for an instant. It released at that point. It still does that occassionally though.

Jan 27, 2008 | Dewalt DW056 18 Volt Cordless Impact...

Not finding what you are looking for?
Buffalo Tools COCD24 24 Volt Cordless Hammer Drill Logo

Related Topics:

121 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buffalo Tools Drills Experts

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

yadayada
yadayada

Level 3 Expert

74945 Answers

Brad Brown

Level 3 Expert

15441 Answers

Are you a Buffalo Tools Drill Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...