Question about Mitsubishi VS-50111 50" Rear Projection Television
Hi, i have connected the cable line directly to the t.v into ant-a but i am only receiving 12 channels, i have tried to add more channels to the memory but it does not work, should i turn off ant-a ? or ?
To answer your question;
Connecting to ant.A will do fine.
Go into your menu and look at "ant.A" if it is written"air" you`ll have to switch it to "cable" and then memorize/scan for channels.
If you`d like the owners manual just click HERE
Hope this help and good luck
Posted on May 26, 2010
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Tips for a great answer:
Jun 16, 2011 | Philips Televison & Video
press and hold the POWER button
on the TV control panel for 5 or more seconds to reset the TV.
Then connect the TV tt any source like outdoor areiel or cable box etc, select the appropriate input, and retune the TV. First of all, connect it to an external antenna, and set it to autotune.
• You must configure the ANT/CABLE input source before
programming channels (-left-hand column).
• If the ANT/CABLE input signal type is set to Cable, the
automatic channel programming process erases channels
that were previously programmed into the TV's memory.
• If the ANT/CABLE input signal type is set to Antenna, the
automatic channel programming process adds newly found
channels to the existing set of programmed channels (and
does NOT erase channels that were previously
programmed into the TV's memory.) To remove an Antenna
source channel from the memory, you must manually delete
• To tune the TV to a channel not programmed in the channel
memory, you must use the Channel Number buttons on the
• Programming channels when the ANT/CABLE input is
configured for Cable will take substantially longer than when
the antenna input is configured for Antenna. This is normal;
however, once channel programming is finished, you should
not have to repeat the programming process again unless
your Cable TV service lineup changes significantly.
Find out the received channels are clear or not. If they are clear, your TV is perfect, and the input device you connects ot the TV is faulty. OK.
Feb 16, 2011 | Toshiba REGZA 42 in. Flat-Panel LCD HDTV
Feb 13, 2011 | Syntax Olevia 532H 32 in. LCD HDTV
Jan 04, 2011 | Sony FD Trinitron WEGA KV-32FS120 32" TV
1 Find and disconnect the cable that is connected to the
ANT IN terminal on your cable box.
? This terminal might be labeled "ANT IN", "VHF IN" or
2 Connect this cable to a two-way splitter.
3 Connect an Antenna cable between an OUT terminal on
the splitter and the IN terminal on the cable box.
4 Connect an Antenna cable between the ANT OUT terminal
on the cable box and the B-IN terminal on the RF(A/B)
5 Connect another cable between the other OUT terminal on
the splitter and the A-IN terminal on the RF (A/B) switch.
6 Connect the last Antenna cable between the OUT terminal
on the RF (A/B) switch and the ANT IN (AIR/CABLE)
terminal on the back of the TV.
After you have made this connection, set the A/B switch to the
"A" position for normal viewing. Set the A/B switch to the "B"
position to view scrambled channels. (When you set the A/B
switch to "B", you will need to tune your TV to the cable box's
output channel, which is usually channel 3 or 4.)
Jan 01, 2011 | Samsung SlimFit TX-T2782 HDTV
Oct 20, 2009 | LG RC897T DVD Recorder/VCR Combo
Mar 02, 2009 | Daewoo DV-T47N VCR
Jan 28, 2009 | Hitachi VTF392A VCR
Jan 16, 2009 | Sharp 27R-S50 27" TV
May 23, 2014 | Mitsubishi VS-50111 50" Rear Projection...
69 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: