Question about NorStar BayStack 425-24T (AL2012E41) 24x10/100 Mbps and 2x1000 Mbps Networking Switch

1 Answer

Baystack 425-24T Port 26 disabled

Hi,

I have a standalone 425-25T and port 26 is disabled. I cannot find a way of enabling it.

Someone in september on this forum suggested using the "no shutdown port 26" command from the CLI, but i get the response Bad Port number.

Any Ideas ????

Posted by on

  • Anonymous Nov 11, 2008

    Hi,

    Someone suggest me to change "stacking-mode" to standalone. I did, but it also does not work. I still connot find port 26.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

I did what you sugget. Went to CLI and did :

conf t

stacking-mode disable
boot

After the reboot, port 26 is enabled and working. Thanks

Posted on Jul 08, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Problem with cisco sg500


I'm not familiar with the device, but it might be something in the configuration. It could be DHCP, it could be something deeper.
I suggest contact Cisco support directly, they have support forums too.

Dec 11, 2013 | Cisco Small Business 500 Series Stackable...

1 Answer

Everyday I need to reboot SMC8024L as systems not getting IP address from stand alone DHCP server could you please suggest what needs to be done here ??


The lease time on DHCP IPs is usaully set for 24 hrs. Try assigning a static IP or changing the lease time. These settinbg are located in router.

Dec 21, 2012 | SMC8024L2 TigerSwitch Standalone 24-Port...

1 Answer

How to connect 2 unmanaged 24 port switch as one unit


You can connect them using a x-over cable to an unused port. the switch should detect the other switch and trunk it automatically. (don't connect more than 1 or you will get a switching loop and possibly a broadcast storm... which is bad)

Jun 04, 2012 | Nortel Networks BayStack 42024T Switch...

1 Answer

Access denied


yes, you should be able to connect to the console port using a roll-over cable RJ45-DB9, connect using hyper terminal or similar using the com port settings 9600,8,N,1
You can then configure the switch from the CLI...

Have you set the 'Login' command on the VTY lines in the switch setup and an IP address on the management VLAN to connect to.
You also HAVE to have a password enabled on the vty lines in order to connect via telnet.

hope this helps.

May 09, 2012 | Cisco Catalyst 2960-24PC-S Ethernet Switch...

1 Answer

I need to disable ports on my network so that they aren't open for non network workstations to plug into how do I do this on an alcatel 7700 switch


interfaces (slot/port) admin down
eg
interfaces 3/24 admin down

The above example will disable port 24 on slot 3. Admin up to enable it again.

Aug 08, 2011 | Alcatel OmniSwitch 7700

3 Answers

How to connect netgear fs108 to cable modem


leeb..... switches cannot be connected to the Cable modem.... because NAT will not be enabled in cable modem....so there wont be any DHCP server present in the cable modem....
Nat will be enabled only in DSL modem like AT&T verizon etc....So DHCP server will be present inside DSL modem...that is the reason why switches can be connected only to the DSL modem....
With NAT enabled modem, switch will work as a switch.... With NAT disabled modem, switch will work as a hub.... This is the difference....
Any doubts further ? please clarify with me.... I am ready to help you....

May 09, 2010 | NetGear FS108 8-Port Ethernet Switch

1 Answer

Uplinking Using Gig Copper


hello, use the plugin modules for the rj 45 connection port to uplink it.

Aug 04, 2009 | Networking Hubs & Switches

1 Answer

Baystack 425 flashing amber on all ports


Make sure you're using the correct console cable...if it's not wired correctly, hyperterminal will continue to give you a blank stare no matter what you do. A great way to verify your cable is to try it on another switch that's working ok. Your hyperterminal comm settings should be 9600 baud, 8 data bits, one stop bit, no parity, and flow control disabled...assuming no one changed the default console settings on the switches.

If you are still having trouble getting a prompt from the console, you can try the following procedure, although this is only known to work on earlier versions of the Baystack switches...

Shut down the power and wait for about a minute. With hyperterminal connected...turn on the power and type "NetICs" (don't include the quotes) within 15 seconds of turning on the power. This should place you in a privileged mode and allow you to use the menu to reset the switches to factory defaults. Good luck!

Jan 12, 2008 | NorStar BayStack 425-24T (AL2012E41)...

1 Answer

Gbic


Hi from the command line interface you will need to login and then type enable (enter) configure (enter), interface fast ethernet all (enter), no shutdown port (port #). Here is a link to the CLI manual if you need more help: http://www116.nortel.com/docs/bvdoc/baystack/doc_pdf/217152-A_CLI_Guide_for_Ethernet_Switch_325-425_Release_3.5.pdf Let me know how it goes or if you need more help. Regards

Sep 25, 2007 | NorStar BayStack 425-24T (AL2012E41)...

Not finding what you are looking for?
NorStar BayStack 425-24T (AL2012E41) 24x10/100 Mbps and 2x1000 Mbps Networking Switch Logo

Related Topics:

656 people viewed this question

Ask a Question

Usually answered in minutes!

Top NorStar Networking Hubs & Switches Experts

Mike

Level 3 Expert

4331 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18299 Answers

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Are you a NorStar Networking Hub and Switch Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...