Question about Kenmore 24 in. 16462 / 16464 / 16469 Built-in Dishwasher

1 Answer

Mydishwasher is stuck on 4hr delay for almost a week i have restart the breaker the reset button also but still blinking 4

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 901 Answers

Refer user manual. The master reset option only known to the authorized service provider.

If they let you know over phone you can arctivate by pressing the buttons as per the sequence & procedure.

Contact the service provider. When he does the job note down the operations.

Even after the master reset the same fault is there, the micro controller has to be replaced.

Posted on May 26, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Help my SMEG dishwasher was stuck in a loop and when resetting it was going through the motions like it was trying to drain itself and then finishing the cycle so all 4 lights on the right were flashing...


completely unplug it for several minutes. if you do not have a plug, turn off the breaker to this unit for about 15 minutes. Then turn it back on and see if this resets it. Check for a reset button somewhere under the unit or on the door panel where the control buttons are if this is easier.

Mar 04, 2015 | Smeg Dishwashers

1 Answer

How to use the delay timer on my washing machine


Each time you press it it changes the amount of time before the chosen program will be finished

eg 4hr means in 4 hours the cycle will finish

Sep 27, 2014 | Bosch Washing Machines

1 Answer

My 8 hr delay button is stuck on help!


Good Morning Friend,

I understand that the 8 hour delay button is stuck on your Frigidaire washer, model# GLTF530DS. With the model number that you have provided, I do not show that there is an 8 hour delay button. I suggest resetting your appliance, by either unplugging it or shutting the power off at your home's circuit breaker, for 3-5 minutes. Restore power and start any cycle. I ask that you please follow up with a comment on the post, at your convenience, to advise if further troubleshooting is needed or if your washer status has changed successfully. If further troubleshooting is needed, I ask that you please leave me the model number of your appliance. Typically this can be found either on the back of the door or around the edges where the door meets your washer. Hope this is helpful.

-Best Regards-
WP

Jun 08, 2014 | Frigidaire GLTF530DS Front Load Washer

1 Answer

How do you set the light delay, I lost my instruction booklet.


The 4½ minute interval can be changed to 1½, 2½ or 3½ minutes as follows: Press and hold the Lock button until the light blinks (about 10 seconds). A single blink indicates the the time is reset to 1½ minutes. Repeat the procedure and the light will blink twice, resetting the timer to 2½ minutes. Repeat again for a 3½ minute interval, etc., up to a maximum of 4 blinks and 4½ minutes.


Jan 04, 2011 | Sears Craftsman LiftMaster Chamberlain...

2 Answers

How to cancel delay start


Press the Delay Start button several times until the displayed delay start time is cleared or reads "00". Unplug the machine or flip the circuit breaker to the OFF position for at least half an hour or so to forcibly reset the control if pressing the Delay Start button does not alter or clear the displayed delay start time.

Nov 09, 2010 | Frigidaire ATF6000ES Front Load Washer

1 Answer

Dishwasher Clean light blinks constantly.


Try turning off the power to the dishwasher at the circuit breaker box. leave the power off for 5 10 mins and then turn breaker back on and try to restart dishwasher. This may reset the board and it may work

Feb 05, 2009 | Kenmore 16602 / 16604 / 16609 Built-in...

2 Answers

Lock Light Blinking


silly question but did you try holding the control lock button(perhaps its the heated dry button) in for 3 secs???? sonds as if the CONTROL LOCK has benn activated( child lockout)

Jan 14, 2009 | Kenmore 24 in. 15932 Built-in Dishwasher

11 Answers

Ge quiet power 3 dishwasher


According to the GE repairman who visited, the solution is to close the machine (with the lights flashing). The machine starts and goes through the cycles, which it does rapidly and then all the lights turn off and the machine becomes silent after 1-1/2 to 2 minutes. Then the machine has been reset to normal. During this reseting period nothing happens inside the machine, although you may hear a running sound.

Thus, the solution is to run the machine in this flashing light state for the 1-2 minutes it takes to go raipdly through each cycle and then reset.

I hope this helps.

Oct 09, 2007 | General Electric Adora GHDA670N Built-in...

Not finding what you are looking for?
Kenmore 24 in. 16462 / 16464 / 16469 Built-in Dishwasher Logo

182 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Dishwashers Experts

Ken Johnston
Ken Johnston

Level 1 Expert

56 Answers

Fred Sops

Level 2 Expert

272 Answers

D. E. Hev

Level 3 Expert

1179 Answers

Are you a Kenmore Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...