Question about Zanussi ZWD1470W Front Load Washer / Dryer

2 Answers

GE front load dryer

The dryer has power but when I hit start button they drying light comes on but dryer does not start.

Posted by on

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Clothing gets caught in the front of the dryer as it spins. This is leaving black marks and wholes in our clothing.

Posted on Jul 15, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I have the same problem did you get it fixed?

Posted on Aug 21, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do I dry clothes


Either hang them up wet or put in clothes dryer

Nov 26, 2014 | Malber WD1000 Front Load Washer/Dryer

1 Answer

How may belts on lg tromm dryer


The start button is a momentary start button. It energizes a relay type switch to keep power on. Try holding the start button in for awhile and do not let go. If the machine keeps running, then for sure, the relay type switch is defective and needs to be replaced with a new one.

May 24, 2014 | LG TROMM WM2688H 4.0 cu.ft. Front Loading...

1 Answer

The Dryer won't start. Power light just flashes red on and off


There are too many problems that it could be, anything from the Button going bad, to the Door Shut Switch being defective, to the Motor, Relay inside the circuit board, to loose wire during the move, and the list goes on and on. Unless you can test each component that sends the START signal, nobody will be able to assist you with the information you have provided.

Mar 01, 2014 | Hotpoint Ariston AWD129 Front Load...

1 Answer

Ge adora washing machine beeps when pushing start with door closed


Hit the power button until there is NO display . Unplug and wait a minimum of 30 seconds , plug back in and within 30 seconds hit SIGNAL button then DELAY START button then SIGNAL button again then DELAY START button again. door should lock and display t01 It is now in test mode . There are 14 different test it can run through in this mode , but all we are trying to do is check for error codes now and maybe get you back to normal, So turn the knob one click clockwise and hit the START/PAUSE button and see if any error codes come up. To exit the diagnostic mode - hit signal button then delay start button then signal button then delay start button and you are out of service test mode and back to normal. Post any error codes.

Dec 07, 2012 | GE WSXH208A Front Load Washer

2 Answers

Asko WCAM1812 Front Load All-in-One Washer / Dryer It does not start the lights are blinking on spin. the door remains unlocked


hold down the "cycle signal" button for 3-5 sec. unplug and plug back in. should clear and reset computer

Aug 08, 2009 | Asko WCAM1812 Front Load Washer / Dryer

3 Answers

Dryer doesn't work.


Dry will not start, light is off. Power is on and working fine to dryer - is there a reset button?
Performa oversized Capacity Plus Model #PYE3360AYW .

Jan 18, 2009 | Maytag MAV3905EWW 13 Cycle Washer

1 Answer

Whirl pool dryer LEC9000PW0 will not turn on


Has a household fuse blown or has a circuit breaker tripped?
There may be 2 household fuses or circuit breakers for the dryer. Make sure both fuses are intact and tight, or that both circuit breakers have not tripped. Replace the fuse(s) or reset the circuit breaker(s). If the problem continues, call an electrician.
Is the correct power supply available? (Electric dryers only)
Electric dryers require 240-volt power supply. Check with a qualified electrician.
Is the dryer door firmly closed?
Your dryer door may not be fully closed. It may look shut, but may not be latched. Push on the door to engage the latch or latches. Some models have an upper and lower latch. Both latches must be secure for the dryer to run.
Was the Start, Push to Start or Hold to Start button firmly pressed?
Large loads may require the Start, Push to Start, or Hold to Start button to be pressed and held for two to five seconds.
Is the Cycle Control knob set on a Sensor Dry or Timed Dry cycle? (on some models)
The Cycle Control knob must be set in a Automatic Dry or AccudryTM or Timed Dry cycle. The dryer will not start if set on the Wrinkle ShieldTM option.
Is Controls Locked status light on? (on some models)
Press and hold the Cycle Signal button for three seconds. This will turn off the Controls Locked feature.
Did you recently install a power supply cord on the dryer? (Electric dryers only)
The power supply cord may be incorrectly installed. If the power cord is incorrectly installed, the dryer may not start or heat. Review the Installation Instructions to check that the power supply cord is properly installed.

Dec 02, 2008 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

GE WBVH6240F


I got the same problem...

Jun 01, 2008 | GE WBVH6240F Front Load Washer

Not finding what you are looking for?
Zanussi ZWD1470W Front Load Washer / Dryer Logo

787 people viewed this question

Ask a Question

Usually answered in minutes!

Top Zanussi Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1456 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Are you a Zanussi Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...