Question about Sony Blu-ray/dvd player BDP-S1

1 Answer

Only Power On light and Light on far Right come on

This happens when I press the powr on with the remote.  Inorder to Turn it off I have to hold down the Power button on the player for 5 seconds. Nothing else works, no display light, no open or close tray. I tried reseting it accord to the manuel. but when i hold down that button and press the power button on the player nothing happens. Would appreciat any help. Ps. used the player yesterday to play a regular dvd and it was working fine Mike

Posted by on

  • cole701 Mar 29, 2009

    I have the same exact problem. Power button light comes on and open/close button light comes on but no display or any other action. I had to take the cover off to manual eject the DVD from the drive. I don;t see any hope for it and guess I will just have to replace it. Basic out of warranty repair is $262 from Sony eSupport so I guess it is time for an upgrade.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Remove remote controll batteries and replace it , possibility get new ones

Posted on Apr 11, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Magnavox error codes


check this
The Service Default Mode (SDM) is a technical aid that can be used to display the your TV error code.
Follow these instrutions exactly to place your set in SDM Mode.
For sets that still have video do the following.
  1. Turn your TV on
  2. Using the original Philips TV remote press the following keys. Press each key for 1 sec then press the next.
  3. From the remote press 0 6 2 5 9 6 MENU
  4. You should now see the letters "SDM" in the far right hand corner.
  5. If not do step "3' again.
  6. To display the error code hit the "Status" button on your remote.
  7. The TV can store up to "7" past errors.
sdm.jpg
For sets that have no video do the following.
  1. Turn your TV on
  2. Using the original Philips TV remote press the following keys. Press each key for 1 sec then press the next.
  3. From the remote press 0 6 2 5 9 6 MENU
  4. Wait a few seconds. The red power light should begin to blink.
  5. The blinking sequence will determine the error code.
  6. You will have one long 5 second red blink followed by the error code.
Note: On some sets the TV will automaticaly blink the error code when its powered up without having to go into the SDM menu. If you power light blinks after the set is powered up jot down the sequence.
Example Error Codes from the power light.
( RED 5 Seconds ) off ( RED 1/2 Sec ) off ( RED 1/2 Sec ) off ( RED 1/2 Sec ) = Error Code 3
Example #2
( RED 5 Seconds ) off ( RED 1 Sec ) off ( RED 1/2 Sec ) off ( RED 1/2 Sec ) = Error Code 12
error-codes.jpg


(Note:) Logo/images/Pictures has a respective copyright. I used it for demonstration purpose only.
If something in your mind to comment or suggest, please let us know. In our efforts to provide detailed information, there is possibility of inaccurate contents. If you see any mistake or incomplete in our information, please don't hesitate to tell us. We will fix it immediately as soon as possible.

Jul 04, 2014 | DVD & Blu-Ray Players

Tip

Sony BDP-S360, BDP-S350 region free code


Full procedure for a oneforall remote is as follows:

1. Press DVD
2. Hold the magic button until the DVD button flashes twice.
3. Press 0533

4. Hold the magic button until it flashes twice.
5. Press 994
6. Press Magic Key (don't hold)
7. Press 00189 (if your oneforall remote uses 4 digit or 3 digit codes, use less leading zeros)
8. Press 1 ( this sets it to key 1 - it flashes twice )

9. Hold the magic button until it flashes twice.
10. Press 994
11. Press Magic Key (don't hold)
12. Press 00255
13. Press 2 ( this sets it to key 2 - it flashes twice )

14. Hold the magic button until it flashes twice.
15. Press 994
16. Press Magic Key (don't hold)
17. Press 00095
18. Press 3 ( this sets it to key 3 - it flashes twice )

19. Hold the magic button until it flashes twice.
20. Press 994
21. Press Magic Key (don't hold)
22. Press 00221
23. Press 4 ( this sets it to key 4 - it flashes twice )

24. Hold the magic button until it flashes twice.
25. Press 994
26. Press Magic Key (don't hold)
27. Press 00079
28. Press 5 ( this sets it to key 5 - it flashes twice )

The remote is now programmed and ready to use, to make the BDP-S360 region free:

1. Use the remote that came with the player to bring the player out of standby, make sure there isn't a disc in it.
2. Press 1, 2, 3, 4, 5 on the oneforall remote. The 24p light will start flashing. (Centre light)
3. Put the player back into standby with the Sony remote.
4. Hard reboot machine (remove power)to prevent the 24p light flashing indefinitely.
5. Next time you turn on the player it will be region free for DVD playback.

on Mar 07, 2010 | DVD & Blu-Ray Players

2 Answers

I have a remote control with one bad button that doesn't work. The product is rare. Is there a way to use another device to send the codes to a portable dvd player


Lost your Remote? Need help programming your GE Universal Remote? Most TV's, VCR's, DVD Player's, Cable and Satellite Boxes will work with a GE universal remote. There is still a chance that your component will not be compatible with the remote. For a list of the codes scroll down to resources and click on the link that applies to you. Follow these steps and we will hopefully get your remote working like new
instructions on how to use it:

  • 1 Manually turn the device on you want to program.
  • 2 Press and hold setup until the light stays on, then release the button.
  • 3. Press the button on the remote of the device you want to program. (EXAMPLE: TV, VCR, DVD, CBL/SAT)
  • 4 Enter the 3 digit code from the list for the device you want programmed. (Some devices might have more then one 3 digit code. Start with the first code) After you enter a code the light will turn off. (For a list of codes scroll down to resources and click on the link that applies to you.)
  • 5 Aim your remote at the device and hit power, your device should turn off. (If the device doesn't turn off start over and move on to the next 3 digit code.) Turn you device back on with the remote and try your volume and channel buttons just to verify everything is working properly.
  • 6 If none of the codes worked for you continue with the next step.
  • 7 Manually turn on the device you want to program.
  • 8 Press and hold setup until the light stays on, then release the button.
  • 9 Press the button on the remote of the device you want to program. (EXAMPLE: TV, VCR, DVD, CBL/SAT)
  • 10 Press and release the power button until your device turns off. Wait a couple seconds before each time you press power. (This is going through a code search with your remote, you might have to press the power button up to 250 times.)
  • 11 When your device turns off press enter. The light on the remote should go off.
  • 12 If neither of the steps worked for you then your device is not compatible with that GE Universal Remote.



  • performance chips of BMW.


    May 31, 2012 | Sylvania SDVD9000 Portable DVD Player

    1 Answer

    I have requirement of region code cracker for sony 3d E370


    hi,
    To make your BD player you need One for all universal remote control

    Full procedure for a oneforall remote is as follows:

    1. Press DVD
    2. Hold the magic button until the DVD button flashes twice.
    3. Press 0533

    4. Hold the magic button until it flashes twice.
    5. Press 994
    6. Press Magic Key (don't hold)
    7. Press 00189 (if your oneforall remote uses 4 digit or 3 digit codes, use less leading zeros)
    8. Press 1 ( this sets it to key 1 - it flashes twice )

    9. Hold the magic button until it flashes twice.
    10. Press 994
    11. Press Magic Key (don't hold)
    12. Press 00255
    13. Press 2 ( this sets it to key 2 - it flashes twice )

    14. Hold the magic button until it flashes twice.
    15. Press 994
    16. Press Magic Key (don't hold)
    17. Press 00095
    18. Press 3 ( this sets it to key 3 - it flashes twice )

    19. Hold the magic button until it flashes twice.
    20. Press 994
    21. Press Magic Key (don't hold)
    22. Press 00221
    23. Press 4 ( this sets it to key 4 - it flashes twice )

    24. Hold the magic button until it flashes twice.
    25. Press 994
    26. Press Magic Key (don't hold)
    27. Press 00079
    28. Press 5 ( this sets it to key 5 - it flashes twice )

    The remote is now programmed and ready to use, to make the BDV-E370 region free:

    1. Use the remote that came with the player to bring the player out of standby, make sure there isn't a disc in it.
    2. Press 1, 2, 3, 4, 5 on the oneforall remote. The 24p light will start flashing. (Centre light)
    3. Put the player back into standby with the Sony remote.
    4. Hard reboot machine (remove power)to prevent the 24p light flashing indefinitely.
    5. Next time you turn on the player it will be region free for DVD playback.
    ok

    Aug 08, 2011 | Sony DVD & Blu-Ray Players

    1 Answer

    I have dish network and an apex 1225 dvd player. i do not have a remote for the dvd player. i do however have a dish network platinum remote control. i am in need of the code to link this remote control to...


    Try the steps below these processes are called a power scans, there is a different type for any equipment needed. This should take 5-6 minutes per item to program.

    For DVD/VCR's:
    1.) Press and hold the correct VCR/DVD button (about six seconds) until all mode button backlights come on, then release.
    2.) Press 222 pound (#) then record three times.
    3.) With the desired equipment on, press and hold the VCR/DVD button until all mode button backlights illuminate (about 3 seconds), then release.
    4.) Press and release the Power button.
    5.) Press the Up button once a second while pointing the remote at the desired equipment. If the code for the equipment comes up, the equipment will power off.
    6.) Press the POUND (#) button. If the code entered is valid for the remote, the mode light flashes three times.

    For TV's:
    POWER SCAN
    1.) Hold down the clear "TV" button on the remote for four seconds, then press 500 pound ( #)
    2.) Hold down the clear "TV" button on the remote for four seconds, press the big power button once.
    3.) Press the channel up button once per second until the TV turns off then press pound (#).

    For any other equipment:
    Power Scan AUX
    1.) With the desired equipment on, press and hold the correct AUX button until all mode button backlights illuminate (about 3 seconds), then release.
    2.) press 0 for a TV, press 1 for a VCR/DVD, press 2 for any other device, then press *.
    Press and release the large red Power button.
    3.) Press the Up button once a second while pointing the remote at the desired equipment. If the code for the equipment comes up, the equipment will power off.
    Press the POUND (#) button. If the code entered is valid for the remote, the mode light flashes three times.
    With any of these methods verify the code works by trying several different functions for that equipment.

    Daniel Busa
    DISH Network
    Customer Service

    Mar 20, 2011 | Apex Digital AD-1225 DVD Player

    1 Answer

    How do you get BDP-S360 to play all regions?


    hi,
    to make ur player region free for dvd u should have a Oneforall universal remote wich acept 4 digit code
    Firs of all u have to program the remote for the purpose. procedure is as follows

    Full procedure for a oneforall remote is as follows:

    1. Press DVD
    2. Hold the magic button until the DVD button flashes twice.
    3. Press 0533

    4. Hold the magic button until it flashes twice.
    5. Press 994
    6. Press Magic Key (don't hold)
    7. Press 00189 (if your oneforall remote uses 4 digit or 3 digit codes, use less leading zeros)
    8. Press 1 ( this sets it to key 1 - it flashes twice )

    9. Hold the magic button until it flashes twice.
    10. Press 994
    11. Press Magic Key (don't hold)
    12. Press 00255
    13. Press 2 ( this sets it to key 2 - it flashes twice )

    14. Hold the magic button until it flashes twice.
    15. Press 994
    16. Press Magic Key (don't hold)
    17. Press 00095
    18. Press 3 ( this sets it to key 3 - it flashes twice )

    19. Hold the magic button until it flashes twice.
    20. Press 994
    21. Press Magic Key (don't hold)
    22. Press 00221
    23. Press 4 ( this sets it to key 4 - it flashes twice )

    24. Hold the magic button until it flashes twice.
    25. Press 994
    26. Press Magic Key (don't hold)
    27. Press 00079
    28. Press 5 ( this sets it to key 5 - it flashes twice )

    The remote is now programmed and ready to use, to make the BDP-S360 region free:

    1. Use the remote that came with the player to bring the player out of standby, make sure there isn't a disc in it.
    2. Press 1, 2, 3, 4, 5 on the oneforall remote. The 24p light will start flashing. (Centre light)
    3. Put the player back into standby with the Sony remote.
    4. Hard reboot machine (remove power)to prevent the 24p light flashing indefinitely.
    5. Next time you turn on the player it will be region free for DVD playback.
    ok

    Jan 22, 2011 | Sony BDPS370 BluRay Player

    1 Answer

    Everytime we try to use the DVD remote the code RC 1 pops up on the player and it doesn't perform the desired function. Is there a simple way to fix that?


    Yes there is a simple way to fix this. I do not have a Panasonic manual in front of me right now but this is how to fix this problem on a different brand. If this does not solve the problem the answer should be within the first few pages of the manual:

    Do this please. Turn off the power to the blu ray player if it is on. Press and hold down 1 and without letting it go press power along with it and hold them down together for more than 5 seconds.
    If the power to the blu ray player turns on walk over to it and turn it off by pressing the power button located on it. If the power to it doesn't turn on then don't worry about that step.
    Next point the remote control at the tv and press and hold down the display button for more than 10 seconds. Now press the power button on the remote control and the bluray player should turn on and off normally and you shouldn't get rc-1 anymore

    Sep 28, 2010 | Panasonic DMR-EZ17 DVD Recorder

    1 Answer

    Need code to Dish Network Remote Control for Sharp DVD Player DV-S1U


    You can power scan for the code.
    Turn ON the electronic device you want to program the remote to control.
    Press the Mode button( sat,tv,dvd,aux) on the remote until the appropriate mode light is flashing.

    Press the Power button. The mode light will stop flashing and stay lit.
    Press the Up or Down arrow button to set the remote to the next code. The Down arrow button scans backward and the Up arrow button scans forward.
    When the correct code is reached, the device (whether a TV, VCR, or other) will turn off.

    Press the pound key button to store the code in the remote control memory. If the code is valid for your remote, the mode light will blink 3 times.
    Turn the device back ON by pressing the Power button.
    Press sat mode key once you power back on the tv to be able to operate the receiver box.
    Try some other functions to make sure you have the correct code. Occasionally the Power button may work when others do not.
    If the other buttons work you are finished.

    .
    If the other buttons do not work, repeat the previous steps. The scan will resume from the last code stored.
    The mode light will flash rapidly when the scan has returned to the starting point and all codes have been tested for that mode. The remote control may not control some device models.

    Apr 20, 2010 | Sharp DV-S1U DVD Player

    1 Answer

    I need the Remote Master 562 code for a Nikkai DVD. It's not mentioned in the instructions.


    Turn on your dvd player, press the DVD mode button, hold down P+ and V- for a couple of seconds until the power button stays lit up...then enter 0005 on the keypad...then, once again, press DVD mode, hold P+ and V- until the power light comes on, and then just keep hitting the power button...

    when your dvd player turns off, thats the right setting, immediatly press P+ and V- to store the code...

    Aug 23, 2008 | DVD & Blu-Ray Players

    Not finding what you are looking for?
    Sony Blu-ray/dvd player BDP-S1 Logo

    Related Topics:

    113 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Sony DVD & Blu-Ray Players Experts

    kakima

    Level 3 Expert

    96683 Answers

    Donald DCruz
    Donald DCruz

    Level 3 Expert

    17129 Answers

    Nasir Muhammad
    Nasir Muhammad

    Level 2 Expert

    148 Answers

    Are you a Sony DVD and Blu-Ray Player Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...