Question about BenQ FP71G 17" LCD Monitor

1 Answer

How to open casing

Hi,

my benq lcd monitor dont have power at all. i plan to see it if it is just the fuse.i already unscrewed my lcd but it is hard to open the case. can you help me to open it. i just worry that it may lead to cracks or damage at all

and above prob.... any ideas on what the possible cause of having no power at all?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Just managed to open a FP17G+ monitor. My hope is that FP17G is similar and that this comes in handy.

There are 5 screws holding the casing together. Four are in the corners (black screws on my monitor). The 5th is right under the monitor stand (silver screw on my monitor.

To open the monitor, I had to:

1) Remove the monitor stand. To do so, you need to take out the two screws at the point where the base connects to the monitor (right above the pivot point) and slide out the monitor stand. THis should give you enough space to take out the 5th screw.

2) Unscrew the five remaining screws on the back of the monitor.

3) At the bottom edge of the monitor, there are two gaps between the front and back plastic panels of the monitor. You can place a wide screwdriver in this gap and gently pry apart the front and back of the monitor. Continue around the edge and the monitor will be open.

Best of luck... If you figure out what is wrong inside, let us know (I am trying to fix the same problem).

Posted on Apr 08, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Benq lcd fp0537s on for just 2 second


There are one or two capacitors in the power supply that open," leaving a slight puff at the top" in some cases.

Mar 16, 2012 | BenQ FP92W LCD Monitor

1 Answer

BenQ Q24W5 LCD monitor circuit diagram


HI.............


Repairing BenQ 17′ LCD Monitor

benqlcd.jpg
I came across a common fault problem in BenQ 17′ LCD Monitor. The problem is have power but no display. Once you has opened the LCD cover, check the pico fuse for open circuit (very common), the push pull transistors C5707 for short circuit and the Buck royer circuit p-channel fet FQU11P06 also for short circuit too. For your information, if you can't get the FQU11p06 you can always use FU9024N as a replacement. Resolder all the high voltage transformer pins and replace the components above and I'm sure you will bring back the life of this BenQ 17′ LCD Monitor.
You may go to this fairchild semiconductor website to download the spec of the FQU11P06 P-channel FET.

http://www.fairchildsemi.com/ds/FQ/FQU11P06.pdf


GOOD LUCK.............

Sep 23, 2011 | Computer Monitors

1 Answer

Repair BenQ Q24W5 monitor


HIIIIIIIII...................


Repairing BenQ 17′ LCD Monitor

benqlcd.jpg
I came across a common fault problem in BenQ 17′ LCD Monitor. The problem is have power but no display. Once you has opened the LCD cover, check the pico fuse for open circuit (very common), the push pull transistors C5707 for short circuit and the Buck royer circuit p-channel fet FQU11P06 also for short circuit too. For your information, if you can't get the FQU11p06 you can always use FU9024N as a replacement. Resolder all the high voltage transformer pins and replace the components above and I'm sure you will bring back the life of this BenQ 17′ LCD Monitor.
You may go to this fairchild semiconductor website to download the spec of the FQU11P06 P-channel FET.


http://www.fairchildsemi.com/ds/FQ/FQU11P06.pdf



GOOD LUCK............

Sep 23, 2011 | Computer Monitors

1 Answer

Power led turns on but there is no dispaly


If you are going to DIY and have proper tools and know safety precaution then please read on:
Most common failures in the LCD monitors are bad capacitors (bulging top/seal or leaking) in the power supply (they should be replaced in a set), blown fuses; poor solder joints, failed inverter circuits (blown fuse, shorted transistors, shorted/open transformers), bad lamps (poor solder connections or worn out lamps). You will need to open it up and inspect the inside, see example of failed DELL/BenQ (BenQ made a lot of DELL monitors)monitors to get some ideas what to look for: http://s807.photobucket.com/home/budm/allalbums
Post back what you see inside so we can guide you further and it will help out other people in the future also.

Basic LCD monitor troubleshooting guide:
http://www.fixya.com/support/r6150077-basic_lcd_monitors_troubleshooting

http://en.wikipedia.org/wiki/Capacitor_plague

Capacitors kit: http://lcdalternatives.auctivacommerce.com/ he can make you a set of caps for you.
Replacement board: http://www.lcdrepair.us

Oct 24, 2010 | BenQ FP72E 17" LCD Monitor

1 Answer

My benq lcd fp767 have power but no display,,,i want have a troubleshooting guide about the lcd,,,pls help me


First check the vga cable, video cards of your pc.if all of these are ok open your LCD monitor check the power board for boated capacitor, open secondary pico fuse or fuseble resistor, replace it with the same value. The defective lcd panel can cause of dim dispaly but the power is ok.

Oct 03, 2010 | BenQ FP767-v2 - 17" LCD Monitor

1 Answer

My benq monitor worked for a couple of years then one day it just stopped. FP731 17". I get the green power light but nothing on the screen. Hooked up a different monitor to the computer and it works...


It is almost the same as DELL monitor (BenQ makes monitors for Dell and HP), so look for shorted transistors, cold solder joint, fuse.
If you are going to DIY and have proper tools and know safety precaution then please read on:
Most common failures in the LCD monitors are bad capacitors (bulging top/seal or leaking) in the power supply (they should be replaced in a set), blown fuses; poor solder joints, failed inverter circuits (blown fuse, shorted transistors, shorted/open transformers), bad lamps (poor solder connections or worn out lamps). You will need to open it up and inspect the inside, see example of failed DELL monitors to get some ideas what to look for: http://s807.photobucket.com/home/budm/allalbums
Post back what you see inside so we can guide you further and it will help out other people in the future also.
http://en.wikipedia.org/wiki/Capacitor_plague
Capacitors kit: http://lcdalternatives.auctivacommerce.com/ he can make you a set of caps for you.

Sep 12, 2010 | BenQ FP731 - 17" LCD Monitor

1 Answer

Benq FP91G+ 19" LCD. Green power light briefly flashes on and off, but the screen doesn't come on. What could be the problem?


If you are going to DIY and have proper tools and know safety precaution then please read on:
Most common failures in the LCD monitors are bad capacitors (bulging top/seal or leaking) in the power supply, blown fuses; poor solder joints, failed inverter circuits (blown fuse, shorted transistors, shorted/open transformers), bad lamps (poor solder connections or worn out lamps). You will need to open it up and inspect the inside, see example of failed DELL (BenQ makes DELL monitors) monitors to get some ideas what to look for: http://s807.photobucket.com/home/budm/allalbums
Post back what you see inside so we can guide you further and it will help out other people in the future also.
http://en.wikipedia.org/wiki/Capacitor_plague
http://www.badcaps.net

Replacement board:
http://www.lcdrepair.us

Jul 11, 2010 | BenQ FP731 17" LCD Monitor

1 Answer

Do you know how to open a benq fp91g+ monitor?


Here is the service manual: http://elektrotanya.com/?q=showresult&megnev=BENQ&megnev2=FP91&kategoria=&kat2=all

Most of the time you will use flat blade screw driver, starting at the bottom edge to pry open the case then work your way around, also look at YOUTUBE, just search for HOW TO OPEN LCD MONITOR.

BenQ makes monitors for DELL and HP.
Most common failures in the LCD monitors are bad capacitors (bulging top/seal or leaking) in the power supply, failed inverter circuits (blown fuse, shorted transistors, shorted/open transformers), bad lamps (poor solder connections or worn out lamps). You will need to open it up and inspect the inside, see example of failed DELL monitors to get some ideas what to look for: http://s807.photobucket.com/home/budm/allalbums
Post back what you see inside so we can guide you further and it will help out other people in the future also.
http://en.wikipedia.org/wiki/Capacitor_plague
http://www.badcaps.net

May 15, 2010 | BenQ FP91G+ Monitor

1 Answer

No display


BenQ made a lot of monitors for Dell. You may want to look at Dell pictures.
Most common failure in the LCD monitors are bad capacitors (bulging top/seal or leaking) in the power supply, failed inverter circuits (blown fuse, shorted transistors, shorted/open transformers), bad lamps (poor solder connections or worn out lamps). You will need to open it up and inspect the inside, see example of failed monitors to get some ideas what goes wrong: http://s807.photobucket.com/home/budm/allalbums
Post back what you see inside so we can guide you further and it will help out other people in the future also.
http://www.badcaps.net
http://en.wikipedia.org/wiki/Capacitor_plague

Apr 11, 2010 | BenQ FP757-v2 - 17" LCD Monitor

10 Answers

BenQ FP731 Screen briefly displays then turns off


hi. i had the same problem and fixed it. the problem are the 4 transistors (C5707) one of more are shorted (Q739,Q740 and Q759, Q760). Also the fuse PF751 (3a) has to be replaced in most cases. In my case i replaced the fuse and 1 transistor (C5707)

Dec 06, 2006 | BenQ FP731 17" LCD Monitor

Not finding what you are looking for?
BenQ FP71G 17" LCD Monitor Logo

553 people viewed this question

Ask a Question

Usually answered in minutes!

Top BenQ Computer Monitors Experts

Tony

Level 3 Expert

2598 Answers

Matthew Spark
Matthew Spark

Level 3 Expert

1042 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a BenQ Computer Monitor Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...