Question about Teac AG-370 Receiver

Open Question

Teac ag 550 reciever

The volume cut out a few times around midway and then the power just died

Posted by on

5 Suggested Answers

  • 1 Answer

SOURCE: lost manuel for teac ag d9100 reciever

you can download a manual for $9.99 from User-Manuals.com....I did this today and the manual is identical to the original it seems

Posted on Sep 19, 2008

SOURCE: TEAC AG-D9100 freeze

Always be that legend when the audio amplifier IC damaged

Posted on May 08, 2009

  • 1 Answer

SOURCE: AG-790 teac

Same problem here. My first receiver was doing this, sent it back, and the second did it again. So I remembered an article regarding remotes and florecent lights. I covered up the remote sensor on the face of the receiver and so far no problem. A piece of tape about 1" square was used and so far no problems. jeffspeakers@aol.com

Posted on Jun 07, 2009

  • 1 Answer

SOURCE: Teac AG V7700 Receiver problem powering up

I have a Teac ag-7700 and when I would try to power it on it would shut off. I did get it to turn on for about 10 minutes and then it shut off. Now when I try to power it on the light on volume dial stays lit but the LED does not light up and no sound through speakers.

Posted on Apr 19, 2010

  • 1 Answer

SOURCE: Teac AG-V8520

same problem exactly

Posted on May 31, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Connect phone to AG-550 Receiver


Android?...If so , buy a 1/8" stereo plug to twin RCA male cable assembly and use the AUX input on the reciever

Jan 30, 2014 | Teac AG-H550 Receiver

1 Answer

Teac AG-V3050. Everything looks right but puts out no sound to speakers. Have trien many speakers. Is there a fuse, reset, etc? Thanks


I nce had the relay for the amplifier die on one of my receiver. Basically this will allow the amp to power on and supply voltage to the speakers. Same thing though, i could access all of the menus, adjust setting, and volume but no sound because the amp never clicked on.

Oct 19, 2012 | Teac AG-V3050 Receiver

1 Answer

I have a Teac Receiver AG-D9100, sound cuts off, but if I touch the master volume knob it comes on for a short time. What to do? jmf


This can be related to a fault in the potentiometer as it cut off the tracking of the voltage and gets back to feed the digital circuit. You need to check, sometimes a switch cleaning oil can help.
Try to wriggle the pot control many times as it can help, if not replace.

Oct 07, 2011 | Teac AG-D9100 Receiver

1 Answer

I just want to know the wattage on the Teac AG-V3050


Teac AG-V3050 and Teac AG-V8050 are very compatiable to help with this question the total watts per channel are 100 watts. Hope this answers or at least helps. Excellent unit, great power to supply great sound for the unit at its time.

Jan 24, 2011 | Teac AG-V3050 Receiver

1 Answer

I own a TEAC AG V1020 receiver. One channel keeps cutting out then and back in after a few minutes. When I give the volume control a quick twist louder then back down, the channel returns for a few minutes...


Turn it off and vigorously operate all mechanical controls throughout their ranges many times with special attention paid to any Tape Monitor or other rarely-used controls.

Jan 10, 2011 | Teac AG-V8060 Receiver

2 Answers

Teac ag-d9100 center and surround speakers are not working , very very low volume.. the others all work fine. Anybody know where to start troubleshooting. Its not a fuse that I can see , at least that i...


You have to enable them and turn the volume on them up separately with the speaker config, level trim, and up/down select buttons on the remote. You can also adjust the rear speaker delay time or just hit the test tone button and adjust the volume on each speaker separately as it goes through them one at a time...

Jun 01, 2010 | Teac AG-D9100 Receiver

1 Answer

Fuse blows everytime i turn it on


the blue coloured varacter in your power supply circuit needs to be changed

Mar 30, 2009 | Teac AG-V3050 Receiver

2 Answers

Teac AG-L800 clicking problem


i have this problem and it is a starter relay that is faulty , part number JQX-115F
i think this is a pro job to repair though

Mar 22, 2009 | Teac AG-L800 Receiver

1 Answer

Teac AG V7700 Receiver problem powering up


I have a Teac ag-7700 and when I would try to power it on it would shut off. I did get it to turn on for about 10 minutes and then it shut off. Now when I try to power it on the light on volume dial stays lit but the LED does not light up and no sound through speakers.

Jul 30, 2008 | Teac AG-D8900 Receiver

2 Answers

Lost manuel for teac ag d9100 reciever


you can download a manual for $9.99 from User-Manuals.com....I did this today and the manual is identical to the original it seems

Jul 11, 2008 | Teac AG-D9100 Receiver

Not finding what you are looking for?
Teac AG-370 Receiver Logo

Related Topics:

697 people viewed this question

Ask a Question

Usually answered in minutes!

Top Teac Audio Players & Recorders Experts

 Grubhead
Grubhead

Level 3 Expert

4861 Answers

yadayada
yadayada

Level 3 Expert

70374 Answers

The Knight
The Knight

Level 3 Expert

72650 Answers

Are you a Teac Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...