Question about NAD C720BEE Receiver

1 Answer

Slight bump, no sound

I have had my NAD C720 BEE receiver for about six months. It has worked perfectly up until now. I was moving it from one shelf to another and bumped it very slightly against the shelf, and now there is no sound coming from it, regardless of input (CD, FM tuner, Aux, etc.). Surely such a small tap can't disable the whole unit?? Is there some kind of safety feature that causes the unit to turn off if it's bumped? Please help!

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

The problem's fixed, and it was actually a very simple matter. When I bumped the receiver against the shelf (and the carpet) I must have hit the 'Speaker A' button on the front panel, causing the speakers to be de-selected and hence no sound to be heard. I realized this was the problem when I unplugged the speakers and tried them in the Speaker B slots and they worked. Then I put them back in the A section and pushed the button and voila - fixed!

Posted on Apr 05, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

NAD T752 display totally lit up. FM sound works but no frequency display.


Sounds like display driver board {IC} has damaged. Contact any service technician. Electro help

Dec 08, 2014 | NAD T752 A/v Surround Sound Receiver

1 Answer

Invalid format


What does the error message read? sounds like the tuner board ?

Sep 06, 2012 | Onkyo TX-SR875 Receiver

1 Answer

NAD T-763 receiver. cannot get surround sound. all speakers work. should the 7.1 and or surround be connected to the receiver and what else. stereo works fine....two front speakers, in stereo mode. ...


Have you looked at the manual? There is no internal source that would produce 7.1 audio other than the test tones. Attach a multichannel source according to ITS manual.

Register and download the manual for free at retrevo.com

http://www.retrevo.com/support/NAD-T763-Receivers-manual/id/8043bh646/t/2/

Apr 19, 2011 | NAD T763 Receiver

1 Answer

Hello. I get no sound out of my AVR 7000 Receiver. No cables behind has been touched in the past. I'm trying TEST TONE, and everything seems normal in the display, but still no sound. I use Preout a NAD...


You don't say if all speakers are silent or just the ones to the unspecified NAD power amp. Do ANY speakers work regardless of which device powers them? Could the NAD be the problem?

Dec 25, 2010 | Harman Kardon AVR 7000

1 Answer

My NAD C720 BEE has been unused for some time and when I turned it on today the standby light stays amber and won't produce any sound. It worked the last time it was used. Ideas?


Open up the unit and blow out all the dust and fibers that have accumulated. Pay particular attention to the microprocessor. It is a 1 by 2 inches by 1/8" thick , flat black component with many legs. I hope this solves your problem

Jul 05, 2009 | NAD C720BEE Receiver

1 Answer

Is there a reset button for the NAD Surround Sound Receiver T 751


The only reset that i know of is to unplug it for 15 to 20 minutes. Hope this helps.

Dec 03, 2008 | NAD T751 Receiver

1 Answer

My NAD T763 turns on but no sound comes out of any speakers


HI,
I had the same problem and AH reset did not work. IS there anything else i can do?
Thanks
Adrian

Dec 02, 2008 | NAD T763 Receiver

1 Answer

NAD T760


You should connect the RCA connectors from your turntable into the phono input of the preamp. Also, make sure you have the grounding wire from the TT connected to the grounding on the preamp (if you do not have a grounding point, then just connect it to one of the screws on the preamp). Then connect the output from the preamp to either the Tape or the CD points on the T760. On the front panel press tape monitor and you're done.

Check and let me know how it goes. My set up's working fine except for clarity, which still needs to be perfected. I'm using a normal step-up phono stage.

Regs/ Avinash

Mar 29, 2008 | NAD T760

2 Answers

Receiver wont turn on


It sounds like You have a Bad output Some where and its going in to protect mode disconnect spkrs and make sure volume is Down all the way and power up,Ck your wireing for Freyed wires and shorts at the inputs and outputs good Luck ttech

Jul 09, 2007 | NAD T752 Receiver

Not finding what you are looking for?
NAD C720BEE Receiver Logo

Related Topics:

304 people viewed this question

Ask a Question

Usually answered in minutes!

Top NAD Audio & Video Receivers Experts

gaucherre

Level 2 Expert

180 Answers

Al Kizina

Level 2 Expert

168 Answers

Brad Brown

Level 3 Expert

13531 Answers

Are you a NAD Audio and Video Receiver Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...