Question about Projection Televisions

1 Answer

Model number... The model number is F32690 and the chassis number is ATC113CAL Hopefully this will help you i aso wanted to let you know i picked up a flybox and that wasint the problem..

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Projection T... Master
  • 8,617 Answers

I just posted the troubleshooting info for the gemstar module in my other post to you. This is a very advanced chassis. I have a link where you can get the traing manual and free tech support if you would like it the training manual is 29.99 but the support is free and unlimited they email the manual, if you would like the link let me know.

Posted on Apr 04, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My TV looks like it's in 3D. Turned it on one morning and it looked like that, was fine the night before.


This is a older model and rarely has convergence (3 d) problems.

There is one simple problem that does occur----look carefully at the back of the set where the model number is---is this a PTK195 chassis?

If it is a 195 chassis (not the model number) it has a small removable power board for the convergence----the board does not need to be replaced--if this is your set (195) there are 2 diodes that fail and are cheap to replace.

If I can help let me know with a comment here (the site will email me) and I will tell you exactly what to do.

SD TECH

Apr 13, 2011 | RCA P52926 52" Rear Projection Television

1 Answer

The screen looks like it is double vision, and the bottom is warped? RCA model P52960


This is a older model; Check on the label on the back where the model number is------somewhere there should be a chassis number like PTK195.

It sounds like a convergence problem and these sets rarely have them.

If it is a PTK195 there is (with back removed and set unplugged) a small circuit board suspended above the main boards to the right as you look from the back.

This is (if it is there) the power supply for convergence and most of the time one of two diodes is shorted--------easy to get that board out and I can pinpoint the two diodes IF THIS IS A 195 CHASSIS.


LET ME KNOW WHAT YOU FIND---I am here to help you. If this information told you something you did not know rate this solution as very helpful as I do this here for free.

REGARDS, SD TECH

Aug 11, 2010 | RCA P52926 52" Rear Projection Television

1 Answer

L3 or L6 chassis?


The chassis number for this DLP should be printed at the back where you will find the model number and manufacturing date code as well.

Feb 08, 2010 | Samsung HL-P5063W 50" Rear Projection HDTV

1 Answer

How do I know if it is L6 or L3 chassis


you need to look on the right side of the set (facing the front of the set) for a small label that says
model code...
serial number..
version..
if the version number is blank or PW01 you have the
L3 chassis.
if it says PU02 then you have the L620 chassis
also the L3 chassis has the ballast on a slight angle and the L620 has the ballast straight.

Dec 29, 2008 | Projection Televisions

1 Answer

TV won't turn on after cable outage


No your set would not be like the HD52W19 model ,your model number is on back of tv year,chassis & Model # being 10 yrs old ptk195 model------- older Rca ptk169 these sets are 16yrs old.My guess without hands on chassis Bad Flyback Transfomer.

Dec 02, 2008 | RCA D52W19 52" Rear Projection Television

1 Answer

R52WM24


I will need you to look on the rear tag and let me know the chassis number as that model was produced with two different chassis numbers ITC222 and the ATC221 chassis was used, But the chassis number will be on the tag on the rear panel. Please reply to this same post and I will help you locate the power supply board.

Aug 13, 2008 | RCA R52WM24 52" HDTV Projection Television

2 Answers

Looking for convergence part number


yes they are the same Convergence ICs number STK392-110 you need to replace both ICs. You can get replacement ICs at the following link and they provide free instalation instructions with pics so you can do the job yourself. Heres the link.
http://servicemanuals.vstore.ca/

May 12, 2008 | Hitachi 43UWX10B 43" Rear Projection...

2 Answers

Rca model p52721lv


whats the chassis number Rca has to be cross referenced by chassis number

Mar 19, 2008 | RCA P46924 46" Rear Projection Television

1 Answer

Screen all green


Your set is definatly Toshiba 43A9UE has Chassis A9PJ the parts may be hard to find give Toshiba the Chassis number that should be waht they need. Hope this helps. If you need some part in paticular such as a Green CRT let me know I will try to locate one for you, just would need the tube type and number off the tag on the tube.

Jan 25, 2008 | Projection Televisions

1 Answer

Toshiba projection tv problem


Hi, you have a failed convergence circuit, you didn`t list model & chassis number so I can`t tell you which IC`s your set uses. this is not an easy job for a layperson that has never done this before, (requires removal of main board and un-soldering two large IC`s and replacing them) If you want more info ask away but be sure to give model/chassis so I know which set were dealing with, good luck, BMW Rider

Dec 07, 2007 | Projection Televisions

Not finding what you are looking for?
Projection Televisions Logo

Related Topics:

48 people viewed this question

Ask a Question

Usually answered in minutes!

Top Projection Televisions Experts

Jaime Hernandez

Level 3 Expert

2267 Answers

matt martin
matt martin

Level 3 Expert

1191 Answers

yadayada
yadayada

Level 3 Expert

60792 Answers

Are you a Projection Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...