Question about AEG 24 in. Favorit 50730W Free-standing Dishwasher

Open Question

AEG 50700 Sensorlogic with a C3 warning



Hiya. Pump is growling after wash cycle. It won't switch off except at mains. When turned on again it says 8 mins left, then C3 alert appears.

I had a new heating element put in before Xmas. The Dish Washer is 7 years old, in pristine condition internally, and last repair cost £114.

Maybe it's time for a new one unless a simple logical answer above problems?

Any suggestions? & Thanks


Posted by on

  • Anonymous Dec 28, 2008

    My problem is the same

×

1 Suggested Answer

  • 3247 Answers

SOURCE: aeg sensorlogic 50700 first showed c2 message; we

Error message C3 is most likely indicating the flood switch is triggered. This means water is leaking from under the sump. The C2 error is linked to drain problems which you cleared.

Posted on Dec 29, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why my AEG F55080vi stops after drain cycle (program beginning) and then it stops and I hear 2 beeps and 2 flash continuously?


Definitely, water drain time-out. Error code i20.
The pressure switch doesn't return to EMPTY (1-2) after two drain phases lasting 120 seconds.
Possible causes:
Drain circuit obstructed/blocked; drain pump
interrupted or jammed (foreign bodies); level
pressure switch blocked on FULL (1-3); hydraulic
circuit of pressure switch obstructed; wiring faulty;
circuit board faulty.

Thanks to your detailed description of failure I conclude that in drain phase (after starts drain pump) leaks water and causing a short circuit. I would thoroughly reviewed drain hydraulic circuit. If is alarm displayed and there is no water inside dishwasher then check heater and anti-interference suppressor.

Dado

Jul 12, 2014 | AEG Dishwashers

1 Answer

Aeg favorit 40010vi dishwasher won't fill with water


I have a similar issue on oko favorit 50700. I have checked the flow from the inlet hose into a bucket and it really seems ok, so I think maybe a problem at the inlet to the machine? Plea update if you get a fix!

Mar 24, 2013 | AEG Dishwashers

1 Answer

Lg ldf7932ss growling noise at wash cycle


The LG is known for the main motor bearings (2 small cheap) bearings that are of poor quality and become noisy (growls) after a period of time. I pulled the motor and replaced the Korean bearings with quality German equivalents. This is cheap and solves the problem. (the front bearing closest to the plastic pump is the culprit.

Mar 15, 2013 | LG LDF7932ST Builtin Dishwasher

1 Answer

Aeg electrolux dishwasher wont wash just keeps beeping


well there are several possibility's. What was the washer doing? Rinse or cleaning? If there is standing water in the tub, then the pump went out or is clogged.

Dec 04, 2012 | Dishwashers

1 Answer

Aeg sensorlogic 50700 first showed c2 message; we drained & cleaned filters 3 times; worked half cycle and now showing error message c3?


Error message C3 is most likely indicating the flood switch is triggered. This means water is leaking from under the sump. The C2 error is linked to drain problems which you cleared.

Dec 29, 2010 | AEG Dishwashers

1 Answer

AEG Dishwasher 60820 Sensorlogic Delay timer stuck on 1Hr


This does sound like a problem with the "anti-flood" device that does detect water (leak / spill) at the base of the washer. This device is a protection device that consists of a polystirene float and a micro swithch. Once a water leak od spill is detected it automatically puts the washer in pump out mode. You need to determine if a leak exists that has caused the float to trigger the micro switch and clear the water / leak. This should put the washer back to normal.
However if the senslogic (pc board) has a program fault, the cost of this board = half the cost of a new washer ......

Apr 13, 2010 | AEG 24 in. Favorit 80860iW Built-in...

2 Answers

Powder solenoid


probably the main module ie the pcb you were looking at

Sep 01, 2008 | AEG 24 in. Favorit 50730W Free-standing...

1 Answer

Dishwasher fail on C3 (leak prevention system)


http://www.kunnig-elektro.de/reparatur/spuelen/aeg/zulauf2.html

in German ... anyway a couple of pictures :)

Dec 15, 2007 | AEG 24 in. Favorit 50730W Free-standing...

1 Answer

I have a dishwasher that only works intermitently...


most fault codes are 10, 20,30.........90 not familar with c2. ther is a fault earky on in a prog where if the pressure switch does not retun to empty the prog stops and displays 10 or 30. the pipe leading from the front of the sump to the pressure switch can sag. tieing it up to stop the sag can cure this..

Feb 27, 2007 | AEG 24 in. Favorit 60870M Free-standing...

Not finding what you are looking for?
AEG 24 in. Favorit 50730W Free-standing Dishwasher Logo

Related Topics:

810 people viewed this question

Ask a Question

Usually answered in minutes!

Top AEG Dishwashers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

paul
paul

Level 3 Expert

750 Answers

sonic boom...
sonic boom...

Level 3 Expert

1557 Answers

Are you an AEG Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...