Question about Marshall MXL2003 Professional Microphone

1 Answer

Switch on MXL 2003

Forgive my ignorance but I am just getting started in VO work and bought he MXL 2003. There is a switch that apparently is a ba cut off and a -10db setting.

Since it didn't come with a manual, what is this switch for and when would I use it?

Thank You

Brian Wolf

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

- bass cuttoff does not allow bass frequencies to pass. This is useful to block unnecessary sounds from being recorded, since there is not much intelligible human voice content in the bass range. Cutting off the bass will minimize the sound of thuds, bumps, breath pops, etc.

- -10dB lowers the signal output of the mic by 10 decibels. This is useful when recording very loud instruments that would otherwise clip some gain stages

Posted on Jan 03, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Does an MXL 990 microphone only work with an inbox?


By "inbox" do you mean a transformer that powers it?
Condenser mics need 48 volts (phantom power) to run, so you normally switch the phantom power button on for the channel you have the condensor mic. plugged into.

May 29, 2014 | MXL 990s Professional Microphone

1 Answer

Wire cut


yes it won't start if no lights are on upon pre cranking, especially the headlights. if you fix that wire and still no start and all lights are on try checking the kick stand switch and if all that don't work wire harness fried. I been there. 2003 R1

Jul 27, 2013 | Yamaha YZF-R6 Motorcycles

1 Answer

2003 ford explorer sport trac blower motor and switch not getting any power, it was working fine a while ago and i had to start flipping the switch to head then off then back to head, what is wrong?


The selector switch on the dash controls the blower motor relay, then the fan switch controls the speed. The fan switch gets power from a 40amp fuse and the control panel gets power from two other fuses.
If you are working the control switch to get the fan to work, the control switch may be failing.

May 28, 2013 | 2003 Ford Explorer Sport Trac

1 Answer

Not getting spark when starting stihl ts 400cut off saw plug is wet.


fromsnor38@gmail.com HI GRYDERT your problem could be your on, off switch. This might sound funny, but switch the on off switch real fast several times, then see if you havee fire. If not check your spark plug. If you have a n
ew one try it. If that don't work check the connection at the plug to be sure it is makiong contact with the plug. If all this does't work you will have to go inside to the coil. They don't usually go ba d but it could. But first check to be sure it isn't grounded at the small wire from the switch. Good Luck.

Jun 07, 2011 | Stihl Concrete Cutoff Chop Saw Clutch...

1 Answer

I bought a MXL 990 USB, and I cannot connect it to my PC. I followed all the instructions, but couldn't get a sound from it. Can somebody help me? I have Windows Vista


Make sure you've switched your sound input from the default (internal mic/input) to the MXL 990. This should be somewhere in the sound options.

If you're sure it's not getting power, you need to send it back.

Jul 23, 2009 | Portacom Porta-Com COM-60FC 6 Headset...

2 Answers

Car runs rough and stalls. 03 ford focus code p1299


You have a cooling problem with this vehicle, what happens is that as soon as the engine is running too hot the PCM starts by switching some of the cylinders off to try and control the temperature but if you ignore this the PCM will start cutting out two cylinders at a time and restricting the RPM to 3000rpm only, called limp mode. This trouble code will be registered in the PCM under the code P2199
If you still ignore this the PCM will switch the engine off completely to avoid serious damage to the engine
Have a look at the coolant level, Radiator leaks, Water pump, thermostat, blocked radiator
Hope this will help you

Apr 19, 2009 | 2003 Ford Focus

1 Answer

Help me please


Their website is apparently now in someone else's control as they are apparently out of business. You might want to go to htpp://www.belarc.com and get the free Belarc Advisor which will tell what components are on the motherboard, from which you can search Google for drivers.

Jan 17, 2009 | Computers & Internet

1 Answer

Pls help


The MXL 990s requires 48 volts to operate. If your mixer does not have a phantom power option, you will need to purchase a microphone pre-amplifier with phantom power to interface the microphone to your mixer.

Nov 19, 2008 | MXL 990s Professional Microphone

Not finding what you are looking for?
Marshall MXL2003 Professional Microphone Logo

Related Topics:

114 people viewed this question

Ask a Question

Usually answered in minutes!

Top Marshall Audio Players & Recorders Experts

Tom Chichester

Level 3 Expert

30577 Answers

James Kovacs
James Kovacs

Level 2 Expert

148 Answers

Are you a Marshall Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...